Goldmund PH3.8 Manual de usuario
USER MANUAL
Goldmund PH3.8
Phono Preamplifier
Goldmiund PH3.8 – Phono Preamplifier - 2
Congratulations.
Thank you for purchasing the Goldmund PH3.8 Phono Preamplifier.
You have acquired the best Phono Preamplifier ever made for professional and domestic uses. It
will share its qualities of cleanliness, liveliness and detailed sound reproduction with its illustrious
predecessor the Mimesis PH3. Please take some time to read this manual. It may provide you with
useful information to make your pleasure of listening to the PH3.8 even higher.
INTRO UCTION
GOL MUN PH3.8 – Phono Preamplifier
Goldmund was founded in 1978 and has ever since been dedicated to the accurate reproduction
of sound and image.
At Goldmund, we strive to lead in the creation, development and manufacture of the industry’s
most advanced technologies, including audio and video systems, home-networking and music
distribution.
The guiding principle at Goldmund is to produce a precise sound with the least possible loss of
quality through the different stages. Goldmund will never adopt a technology before it is sufficiently
developed to satisfy the high quality standards we set. This is why Goldmund has often rejected
mainstream technologies and developed its own.
Goldmiund PH3.8 – Phono Preamplifier - 3
Table of Contents
1UNPACKING 5
2 CHOICE LOCATION AN COOLING 5
3 LINE VOLTAGE A JUSTMENT 6
4CONNECTIONS 6
5 REAR PANEL CONTROLS 7
6 FRONT PANEL CONTROLS 10
7 SOUN QUALITY OPTIMIZATION 10
8MAINTENANCE 10
9TECHNICAL ATA 11
10 REAR PANEL 13
Goldmiund PH3.8 – Phono Preamplifier - 4
W A R N I N G !
This extremely high quality phono preamplifier
possesses new technical features which are
necessary for accurate sound reproduction in
the best audio systems.
Only careful installation and use can
provide the satisfaction you are expecting.
The installation instructions must be carried
out in full and the mentioned precautions
taken to get the expected result and to avoid
impairing performance.
Goldmiund PH3.8 – Phono Preamplifier - 5
1 UNPACKING
You will find in the GOLDMUND PH3.8 box:
- The Phono Preamplifier.
- The power cord.
- This manual.
ATTENTION
Please keep the packaging in case you need to transport the PH3.8 at a later date or if you
have to send it for maintenance.
This packaging has been designed specifically to protect the PH3.8 in transit. Use of
alternative packaging is likely to result in damage, invalidating warranty cover.
2 CHOICE LOCATION AN COOLING
The Goldmund PH3.8 phono preamplifier does not generate a significant amount of heat.
The performance of the phono preamplifier is however directly related to its thermal
stability. The PH3.8 must therefore be located to allow adequate cooling of the heatsink
without over-ventilation.
Avoid stacking the PH3.8 with equipment generating heat.
Avoid locating the PH3.8 in direct proximity to any power amplifier, as the field generated
by some units can be detrimental to performance of phono preamplifiers.
Goldmiund PH3.8 – Phono Preamplifier - 6
3 LINE VOLTAGE A JUSTMENT
A voltage selector is provided on the back plate of the preamplifier. Adjust it with a
screwdriver if the line voltage provided is not appropriate.
ATTENTION: On the 220V position, PH3.8 preamplifier will function properly for main line
voltage in between 200V and 250V. On the 110V position, the main line must deliver
between 105 and 125V. If your main line is usually out of these tolerances, please consult
your GOLDMUND dealer.
Note:
Please check the value of the main line fuse. This fuse is located on the power cord
receptacle. The lid can be removed with a small screwdriver when the cord is removed.
Use a 1A slow-blow fuse for 220V and 110V.
4 CONNECTIONS
Connect the power cord to the back of the PH3.8 and plug it into the nearest wall socket.
Use a 3 lug grounded plug for safety.
To get the best sound from the PH3.8, avoid any multiple plugs or extension cords.
Connect the input interconnects between the phono preamplifier and the turntable.
If you are using a moving-coil cartridge select the inputs marked MC-L and MC-R. To
connect a moving-magnet cartridge use the inputs marked MM-L and MM-R.
Note:
Both inputs can be connected simultaneously if no hum is generated. In that case, the front
panel selecting the inputs acts a source selector between the two cartridges or tone-arms.
Plug the output interconnects from the RCA female sockets (labeled “output”) to the
preamplifier.
Goldmiund PH3.8 – Phono Preamplifier - 7
5 REAR PANEL CONTROLS
POWER ON
When first powered on, the preamp will become operative only after approximately twenty
seconds of warm up. This ensures proper stabilization of the circuitry and avoids any
unwanted noise, this delay will also be applied every time a change is done on the front
switches. After this delay, the output of the preamplifier is connected to the output
connectors.
Note:
The GOLDMUND PH3.8 phono preamplifier should remain connected at all times.
If the power cord is accidentally disconnected, a special safety circuit switches the preamp
to muting, to avoid any disturbance to reach the power amplifier and the speakers, even in
case of a power failure in the building.
It is normal for a slight sound to be heard from the speakers when the Phono Preamplifier
is turned ON or OFF. The PH3.8 is self-protected and the sound heard is corresponding to
the charging and discharging of the capacitors.
INPUT MM/MC SELECTOR
This front panel switch controls which input is used: the Moving Magnet or the Moving Coil
input.
GAIN
Level adjustment acting simultaneously on both channels for both the moving coil and the
moving magnet sources.
Goldmiund PH3.8 – Phono Preamplifier - 8
5 REAR PANEL CONTROLS (Ctd.)
BACK PANEL IMPE ANCE SWITCHES
Six switches are located around the preamplifier input connectors. These switches
individually adjust the loading of each input separately for each channel. For Moving
Magnet inputs, both resistive and capacitive load can be adjusted. For Moving Coil inputs,
only resistive load can be adjusted.
Each switch has nine positions, numbered 1 to 9. The table below indicates the values
applied for each selector position:
Selector MC R-Load
(Moving Coil Resistance)
The following values are parallel resistance load applied to the MC inputs.
One selector controls the right input, the other one the left input.
Switch position Load applied on the input
1 - 10 Ohms
2 - 20 Ohms
3 - 50 Ohms
4 - 100 Ohms
5 - 470 Ohms
6 - 1.5 kOhms
7 - 4.7 kOhms
8 - 15 kOhms
9 - 47 kOhms
Goldmiund PH3.8 – Phono Preamplifier - 9
5 REAR PANEL CONTROLS (Ctd.)
Selector MM R-Load
(Moving Magnet Resistance)
The following values are parallel resistance load applied to the MM inputs. One selector
controls the right input, the other the left one.
Switch position Load applied on the input
1 - 50 Ohms
2 - 220 Ohms
3 - 1 kOhms
4 - 5 kOhms
5 - 10 kOhms
6 - 20 kOhms
7 - 33 kOhms
8 - 47 kOhms
9 - 100 kOhms
Selector MM C-Load
(Moving Magnet Capacitance)
The following values are parallel capacitors load applied to the MM inputs. One selector
controls the right input, the other the left one.
Switch position Load applied on the input
1 - 20 pF
2 - 50 pF
3 - 100 pF
4 - 220 pF
5 - 470 pF
6 - 1 nF
7 - 2.2 nF
8 - 4.7 nF
9 - Off
Goldmiund PH3.8 – Phono Preamplifier - 10
6 FRONT PANEL CONTROLS
On the front panel of the GOLDMUND PH3.8 Phono Preamplifier you will find two switches.
The left switch selects the global gain (low or hi) of the preamplifier, the right switch selects
the MM or MC cartridge.
To start playing the Phono Preamplifier, turn the power switch ON located on the back
panel of the preamplifier. The Phono Preamplifier is operative immediately after its self-
test.
7 SOUN QUALITY OPTIMIZATION
If the preamplifier has been left unpowered for a few days, the optimum sound quality is
only reached after a few hours. This is why GOLDMUND recommends leaving the PH3.8
powered on.
8 MAINTENANCE
The GOLDMUND PH3.8 Phono Preamplifier usually requires no maintenance.
Always turn the power off before cleaning your Phono Preamplifier. Use only a clean, soft,
damp cloth. Dampen with water or a mild detergent solution. Avoid abrasive or harsh
cleansers (eg. products containing sodium carbonate).
Tabla de contenidos
Otros manuales de Amplificador de Goldmund
Goldmund
Goldmund TELOS 250 Manual de usuario
Goldmund
Goldmund TELOS 352 Manual de usuario
Goldmund
Goldmund TELOS 1000 NextGen Manual de usuario
Goldmund
Goldmund Amplifiers Manual de usuario
Goldmund
Goldmund MIMESIS 18.4 Manual de usuario
Goldmund
Goldmund Metis 5 Manual de usuario
Goldmund
Goldmund MIMESIS 32 Manual de usuario
Goldmund
Goldmund TELOS 590 NextGen Manual de usuario
Goldmund
Goldmund MIMESIS 22 Manual de usuario
Goldmund
Goldmund METIS 2 Manual de usuario
Goldmund
Goldmund TELOS 280 Manual de usuario
Goldmund
Goldmund MIMESIS 27.5 Manual de usuario
Goldmund
Goldmund PH7.3 Manual de usuario
Goldmund
Goldmund Metis 7 Manual de usuario
Goldmund
Goldmund SR2.3 Manual de usuario
Goldmund
Goldmund MIMESIS 37S Manual de usuario
Goldmund
Goldmund SRI2 Manual de usuario
Goldmund
Goldmund MIMESIS 16 Manual de usuario
Goldmund
Goldmund MIMESIS 28 Manual de usuario
Goldmund
Goldmund MIMESIS 29M Millennium Edition Manual de usuario
