Goldair GSCV280 Manual de usuario

Operating Instructions

2000W Convector Heater

Model: GSCV280

This page has been intentionally left blank.

CAUTION: In order to avoid a hazard due to inadvertent resetting of the

thermal cut-out, this appliance must not be supplied through an external

switching device, such as a timer, or connected to a circuit that is regularly

switched on and off by the utility.

•This appliance is not intended for use by persons (including children) with

reduced physical, sensory or mental capabilities or lack of experience and

knowledge, unless they are supervised or have been given instruction

concerning the use of the appliance by a person responsible for their safety.

•Children should be supervised to ensure that they do not play with the

appliance.

•If the supply cord is damaged, it must be replaced by the manufacturer, its

service agent or similarly qualified persons in order to avoid a hazard.

WARNING: You must not cover this appliance. Covering this appliance

presents fire risk and will activate the safety fuse; permanently disabling the

unit.

WARNING: Do not use this appliance in small rooms when they are

occupied by persons not capable of leaving the room on their own, unless

constant supervision is provided.

WARNING: To reduce the risk of fire, keep textiles, curtains, or any

flammable material a minimum distance of 1 metre from the air outlet.

General Care and Safety Guide

•Use only the voltage specified on the rating label of the appliance.

•Keep all objects at least 1 metre from the front, sides and rear of the

appliance.

•This appliance is intended for household use only and not for commercial or

industrial use.

•Indoor use only.

•Use this appliance only as described in this manual. Any other use is not

recommended by the manufacturer and may cause fire, electric shock or

injury.

•Do not use the appliance if it has been dropped or damaged.

•The common cause of overheating is deposits of dust or fluff in the appliance.

Ensure these deposits are removed regularly by unplugging the appliance and

vacuum cleaning the air vents and grills.

YOUR SAFETY IS IMPORTANT TO US. PLEASE ENSURE YOU TAKE NOTE OF THE

INSTRUCTIONS AND WARNINGS OUTLINED IN THIS MANUAL.

•Never use the appliance to dry clothes.

•Always unplug appliance when not in use.

•When the appliance has been unpacked, check it for transport damage and

ensure all parts have been delivered. If parts are missing or the appliance has

been damaged, contact the Customer Services Team.

•Do not use if there are visible signs of damage to the appliance.

•Do not connect the appliance to mains supply until completely assembled and

adjusted.

•Ensure hands are dry before handling the plug or main unit.

•Ensure appliance is on a flat, stable, heat-resistant surface.

•Do not operate with cord set coiled up as a heat build up is likely, which could

be sufficient to become a hazard.

•Carry out regular checks of the supply cord to ensure no damage is evident

•Do not operate this appliance with a damaged cord, plug or after the appliance

malfunctions or has been dropped or damaged in any manner. Take to a

qualified electrical person for examination, electrical service or repair.

•Do not twist, kink or wrap the cord around the appliance, as this may cause the

insulation to weaken and split. Always ensure that all cord has been removed

from any cord storage area and is unrolled before use.

•It is recommended that this appliance is plugged directly into the wall socket.

Power boards are not rated to supply power to high wattage appliances.

•A correctly specified, undamaged extension cord may be used with this

appliance provided it is used in a safe manner.

•Do not remove plug from power socket until the appliance has been switched

off.

•Do not remove plug from power socket by pulling cord; always grip plug.

•Do not place cord under carpet or cover with rugs or furniture. Arrange the cord

so it cannot be tripped over.

•Don’t place appliance on bedding or on thick & long carpet where the openings

may get blocked.

•Switch off and use handle provided when moving

•Do not place appliance close to radiant heat source.

•Do not insert or allow foreign objects to enter any ventilation or exhaust

opening, as this may cause an electric shock, fire or damage to the appliance.

•Do not sit on the appliance.

•Do not use abrasive cleaning products on this appliance. Clean with a damp

cloth (not wet) rinsed in hot soapy water only. Always remove plug from the

mains supply before cleaning.

•Do not operate in areas where petrol, paint or other flammable liquids are used

or stored.

•Do not use this appliance in the immediate surrounds of a bath, a shower, or a

swimming pool or other liquids.

General Care and Safety Guide

•The appliance must not be immersed in any liquids.

•There are no user serviceable parts installed in the unit.

•Do not place the unit in wardrobes or other enclosed spaces as this may cause

fire hazards.

•This unit is not supposed to be used in or around locations where foodstuffs,

works of art or delicate articles of science, etc. are stored.

•If your appliance does not work, or is not working properly, contact the place of

purchase or the Customer Services Team.

General Care and Safety Guide

Assembly Instructions

WARNING: Heater must not be used without the feet fitted.

This appliance has been supplied with ‘1 way screws’ for permanent installation of the

feet. This is a safety requirement for the New Zealand and Australian market.

ASSEMBLY OF HEATER

Carefully turn the Main Body upside-down on a scratch-free and stable surface. Be careful to

prevent damage to the cosmetic finish or your floor surfacing.

Attach the feet to the base of the heater by aligning the built-in position pins with the position

holes on the base of the heater and fixing a screw into the hole between the two position holes.

Use one screw for each foot.

Main Body x 1

Feet x 2

Screws x 4

Operating Your Heater

Always choose a safe location for the heater, keeping in mind the safety precautions

outlined. Ensure all packaging has been removed from the unit before use. Please

follow the below instructions.

WARNING: In order to avoid overheating or fire, do not cover the heater.

WARNING: Keep all objects at least 1 metre from the front, sides and rear

of the appliance.

WARNING: Do not use this heater with a programmer, separate timer,

remote-control system or any other device that switches the heater on

automatically, since a fire risk exists if the heater is covered or positioned

incorrectly.

WARNING:Never leave this heater unattended when in use.

Ensure heater is on a flat, stable, heat-resistant surface.

Once the heater is in a safe operating position and all switches are in the off

position, insert the power plug into the mains outlet and switch on.

CAUTION: Ensure the power cord is not tight because if pulled it may

partially pull the plug from the socket. A partially inserted plug will overheat

the plug and socket and could result in fire.

Note: When the appliance is turned on for the first time, it may release a

slight odour or smoke. This odour or smoke is a normal occurrence caused by

the initial heating of the internal heating elements and should not occur

again.

HEAT CONTROL SWITCH

The control switch positions are:

0 Off

ILow Heat

II Medium Heat (Turn Low Heat Off first)

I+II High Heat (Low and Medium together)

Check that the Heat Control Switch is set to Off position before plugging the heater

into the mains supply. For greater economy, use the High Heat setting initially and

then switch to the Low Heat setting.

Operating your Convector Heater

THERMOSTATIC CONTROL

1. Rotate thermostat knob clockwise until you reach the

maximum position.

2. When the room reaches a temperature that is

comfortable for you, slowly turn the knob anti-clockwise

until the heater just turns off (you will hear a click).

3. The heater will now cycle on and off to maintain the

comfort level you have set.

4. Take note of this setting position for future use.

Mode switch positions

OFF

TIMER ON

OVERRIDE

Indicates actual time

Riders pushed to the

outside rim to turn ON

TIMER

The heater will always be on when the Mode switch is in the “I” position.

The heater will always be off when the Mode switch is in the “O” position.

To set the Timer; set the MODE switch to the Timer position.

(This function can only be used once a heat level has been selected; see thermostat section).

You must set the time prior to programming the Timer.To do this; turn the outer dial of the

timer in a clockwise direction until the time of the day (24-hour clock) corresponds with the

triangular marking. Example if it is 2pm (1400 hours) then set the triangular mark in line with

14.One complete turn of the dial corresponds to 24 hours.

There are 96 “riders”, positioned around the dial, each rider represents 15 minutes.

Where all the “riders” are pushed to the outside of the timer the heater will be ON

continuously.

To set a specific time for example:

If you want the heater to be on from 6pm to 10pm, then set all the riders from 18 to 22 (1800

hours to 2200 hours) to the outside of the rim and all other riders to the inside of the timer.

The unit will then turn on automatically at 6pm and off again at 10pm.

Operating Your Heater

SAFETY DEVICES

This appliance has two protection devices:

•Resettable Thermal Link - this will automatically disconnect the power to the

appliance at a pre-set overheat temperature. After cooling down it will reset and

power on again. If this occurs, investigate what is causing the appliance to overheat.

•Thermal Fuse - this disconnects the appliance permanently in case of overheating. (It

is non resettable).

CAUTION: The heater generates heat during use. Proper precautions must

be taken to prevent the risk of burns, scalds, fires or other damage to persons.

CARE AND CLEANING

•The heater requires regular cleaning to ensure trouble free operation:

•Unplug the heater from the mains supply before cleaning.

•Ensure that the heater has been allowed to cool down completely before cleaning.

•The common cause of overheating is deposits of dust or fluff in the appliance. Ensure

these deposits are removed regularly by unplugging the appliance and vacuum

cleaning the air vents and grills.

•Use a damp cloth (not wet) to wipe the exterior of the heater to remove dust and

dirt.

•Never use solutions such as petrol, thinners or polishing agents.

•Ensure the heater is dry before plugging back into the mains supply.

•Do not attempt to dismantle the heater. There are no user serviceable parts. For

service or repair, contact an authorised electrical service technician.

This appliance is filled with a precise quantity of special oil. Repairs requiring opening

of the oil container are only to be made by the manufacturer or his service agent who

should be contacted if there is an oil leak. When scrapping the appliance, follow the

regulations concerning disposal of oil.

PROOF OF PURCHASE

To receive warranty retain receipt as proof of purchase.

SUPPORT AND TECHNICAL ADVICE

Goldair –New Zealand

Monday –Friday 8am-5pm

Phone +64 (0)9 917 4000

Phone 0800 232 633

[email protected]

Goldair –Australia

Monday –Friday 8am-5pm

Phone +61 (0)3 9365 5100

Phone 1300 465 324

[email protected]u

Tabla de contenidos

Otros manuales de Calentador de Goldair

Goldair

Goldair GPH150 Manual de usuario

Goldair

Goldair Platinum Series Manual de usuario

Goldair

Goldair GHOR100RS Manual de usuario

Goldair

Goldair Platinum GPPH220 Manual de usuario

Goldair

Goldair GPCV360B Manual de usuario

Goldair

Goldair GBFH200 Manual de usuario

Goldair

Goldair GMH280 Manual de usuario

Goldair

Goldair GCT360 Manual de usuario

Goldair

Goldair GCV370 Manual de usuario

Goldair

Goldair SFH7000 Manual

Goldair

Goldair Platinum GPPH610 Manual de usuario

Goldair

Goldair GCV100 Manual de usuario

Goldair

Goldair PLATINUM GPCV330 Manual de usuario

Goldair

Goldair Platinum GPOC4310 Manual de usuario

Goldair

Goldair GCW220 Manual de usuario

Goldair

Goldair GSOC100 Manual de usuario

Goldair

Goldair GCT325 Manual de usuario

Goldair

Goldair GCW220 Manual de usuario

Goldair

Goldair GCT250 Manual de usuario

Goldair

Goldair GCV280 Manual de usuario

Goldair

Goldair ecopanel GEPH215 Manual de usuario

Goldair

Goldair GFH350 Manual de usuario

Goldair

Goldair GEOH400 Manual de usuario

Goldair

Goldair GFH267 Manual de usuario

Manuales populares de Calentador de otras marcas

oventrop

oventrop Regucor Series Manual de usuario

Blaze King

Blaze King CLARITY CL2118.IPI.1 Manual de usuario

ELMEKO

ELMEKO ML 150 Manual de usuario

BN Thermic

BN Thermic 830T Manual de usuario

KING

KING K Series Guía

Empire Comfort Systems

Empire Comfort Systems RH-50-5 Guía de inicio rápido

Well Straler

Well Straler RC-16B Manual de usuario

EUROM

EUROM 333299 Manual de usuario

Heylo

Heylo K 170 Manual de usuario

Eterna

Eterna TR70W Manual de usuario

Clarke

Clarke GRH15 Manual de instrucciones

IRSAP

IRSAP The Radiator Company Ovali Manual de usuario

Empire Heating Systems

Empire Heating Systems WCC65 Manual de usuario

Wetekom

Wetekom 92 86 43 Manual de usuario

Desa

Desa SPC170-F Manual de usuario

Watlow

Watlow Watrod Electric Tubular Heaters Manual de usuario

Haverland

Haverland ECO-DRY GPS Series Manual de lista de piezas

Stelpro

Stelpro ASILVC2060 Series Manual de usuario