GeoVision GV-APOE0400 Manual de usuario

September 10, 2021

GV-APOE0400 6-Port 10/100 Mbps Unmanaged PoE Switch

with 4-Port PoE

1. Packing List

1. GV-APOE0400

2. AC Power Cord

3. Rubber Feet x 4

Note: If any of these items is found missing or damaged, please contact your local

supplier for replacement.

September 10, 2021

2. Front Panel

The front panel consists of 6 10/100 Mbps ports, 4 PoE and 2 uplink, LED indicators and the

DIP switch.

2.1 LED Indicator

LED Color/Status Description

Off No power supply

Power Orange System powered on

Off No devices connected to the corresponding port

Green Network through the corresponding port has been

successfully established

DATA

Blinking Green Data currently being sent through the

corresponding port

Off No PoE powered devices (PD) connected

Orange At least one device successfully powered through

PoE

Blinking Orange Abnormal power supply

2.2 DIP Switch

The DIP switch can switch on/off the CCTV mode of the system.

[Default Mode] The CCTV mode is switched off by default, in which power is supplied

through the 4 PoE ports over cables of up to 100 m (328 ft) with a network bandwidth of 100

Mbps per port.

[CCTV Mode] Allow power supply over cables of up to 250 m (820 ft) in length, but at the

expense of reducing the network bandwidth of the 4 PoE ports to 10 Mbps per port.

Note: After changing the CCTV mode, it is required to restart the system for the change to

take effect.

September 10, 2021

3. Rear Panel

The AC power socket for powering the system is located at the rear panel and accepts power

input from 100 to 240 V at 50/60 Hz.

4. Installation

Prior to installing the PoE switch, please note the following:

Only clean the switch when it is unplugged and with a dry cloth without involving any

liquids.

Do not place the switch near water or any damp area and prevent moisture from

entering the switch chassis.

Do not place the switch on an unstable surface where it may be severely damaged due

to a fall.

Ensure there is proper ventilation at the installation site and keep the ventilation of the

switch free of obstruction.

Make sure the operating voltage is consistent with as labeled on the switch.

Do not open the chassis during operation or when there are electrical hazards in

avoiding electric shocks.

4.1 Leveled Installation

Attach the four supplied rubber feet at the bottom of the switch and place it on a leveled

surface.

Note: Make sure to leave at least 10 cm of space around the switch for adequate

ventilation.

September 10, 2021

4.2 Wall Mount Installation

For wall mount, make sure to prepare 2 screws of 4 mm in length and 5.5 ~ 7 mm in

diameter and prepare 2 screw anchors of matching size.

1. Drill two evenly-leveled holes on the desired wall that are 122 mm apart.

2. Hammer the two self-prepared screw anchors into the holes on the wall.

3. Insert the two-self prepared screws into the screw anchors and tighten to the point where

there are about 1.5 mm left hanging out.

4. Hang the switch onto the screws with all of its ports pointing downward.

4.3 Powering On the Switch

To power on the switch, connect it to a power source using the supplied AC power cord. The

switch will respond as following upon turning on:

The Power LED is lit.

The DATA LED flashes momentarily, signaling system initiation.

Note: Make sure to leave at least 10 cm of space around the switch for adequate

ventilation.

September 10, 2021

5. Connecting to GV-IP Camera

The switch can be connected to up to 4 GV-IP Camera and 1 GV-VMS / NVR / DVR System.

You can also extend the connection by connecting to another switch.

6. Specifications

For details, please see Datasheet.

Tabla de contenidos

Otros manuales de Cambiar de GeoVision

GeoVision

GeoVision GV-POE0801 Manual de usuario

GeoVision

GeoVision GV-POE2401-V2 Manual de usuario

GeoVision

GeoVision GV-POE0410-E-V2 Manual de usuario

GeoVision

GeoVision GV-POE0800 Manual de usuario

GeoVision

GeoVision GV-APOE0810 Manual de usuario

GeoVision

GeoVision GV-POE2411-V2 Manual de usuario

GeoVision

GeoVision GV-POE0410-E Manual de usuario

GeoVision

GeoVision GV-APOE1611 Manual de usuario

GeoVision

GeoVision GV-POE2411 Manual de usuario

GeoVision

GeoVision GV-APOE4813 Manual de usuario

GeoVision

GeoVision GV-PoE Manual de usuario

GeoVision

GeoVision GV-POE0812 Manual de usuario

GeoVision

GeoVision GV-APOE4813 Manual de usuario

GeoVision

GeoVision GV-POE1601 Manual de usuario

GeoVision

GeoVision GV-POE2411 Manual de usuario

GeoVision

GeoVision GV-POE1611 Manual de usuario

GeoVision

GeoVision GV-APOE0410-E Manual de usuario

GeoVision

GeoVision GV-APOE0400 Manual de usuario

GeoVision

GeoVision GV-POE2411 Manual de usuario

GeoVision

GeoVision GV-POE0811 Manual de usuario

GeoVision

GeoVision GV-POE1611-V2 Manual de usuario

GeoVision

GeoVision GV-POE0811-V2 Manual de usuario

GeoVision

GeoVision GV-APOE0811 Manual de usuario

GeoVision

GeoVision GV-APOE4813 Manual de usuario

Manuales populares de Cambiar de otras marcas

URC

URC Total Control MFS-8 Manual de usuario

Azbil

Azbil HPQ-D11 Manual de usuario

Sony

Sony DFS-900M Manual de usuario

SICK

SICK i17S Manual de usuario

F&F

F&F SZR-277 Manual de usuario

Shure

Shure UAMS/BK Manual de usuario

Dräger

Dräger X-zone Switch Off Manual de usuario

Asco

Asco Joucomatic 349 Series Manual de usuario

BT Mini Hub Manual de usuario

D-Link

D-Link DES-1226G Manual de usuario

Johnson Controls

Johnson Controls FS80-C Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manual de usuario

MicroNet

MicroNet SP1200A Manual de usuario

Ruijie

Ruijie RG-PF2920 Series Manual de instalación y funcionamiento

Altinex

Altinex DA1914SX Manual de usuario

MiLAN

MiLAN MIL-SM2401M Manual de usuario

RJM

RJM MASTERMIND PBC/6X Manual de usuario

Atlas

Atlas MMK-KVM8 Manual de usuario