Generac Power Systems 09227-0 Manual de usuario

POWER SYSTEMS, INC.

Owner’s Manual

100 and 200 Amp

“V” Type and “Y” Type

Transfer Switch

Models: 09227-0, 09228-0,

09229-0, and 09230-0

This manual should remain with the unit.

Generac®Power Systems, Inc.

Generac cannot possibly anticipate every possible cir

cumstance that might involve a hazard. The warn-

ings in this manual, and on tags and decals

affixed to the unit are, therefore, not all-inclusive. If

you use a procedure, work method or operating tech-

nique Generac does not specifically recommend, you

must satisfy yourself that it is safe for you and others.

You also must make sure the procedure, work

method or operating technique that you choose does

not render the transfer switch unsafe.

Throughout this publication, and on tags and

decals affixed to the generator, DANGER, WARNING,

CAUTION and NOTE blocks are used to alert you to

special instruction about a particular operation that

may be hazardous if performed incorrectly or care-

lessly. Observe them carefully. Their definitions are

as follows:

After this heading, you can read instructions that,

if not strictly complied with, will result in personal

injury or property damage.

After this heading, you can read instructions that,

if not strictly complied with, may result in personal

injury or property damage.

After this heading, you can read instructions that, if

not strictly complied with, could result in damage to

equipment and/or property.

NOTE:

After this heading, you can read explanatory

statements that require special emphasis.

These safety warnings cannot eliminate the hazards

that they indicate. Common sense and strict compli-

ance with the special instructions while performing the

service are essential to preventing accidents.

Four commonly used safety symbols accompany the

DANGER, WARNING and CAUTION blocks. The type

of information each indicates follows:

This symbol points out important safety informa-

tion that, if not followed, could endanger personal

safety and/or property of you and others.

This symbol points out potential explosion hazard.

This symbol points out potential fire hazard.

This symbol points out potential electrical shock

hazard.

GENERAL HAZARDS

• Any AC generator that is used for backup power if

a NORMAL (utility) power source failure occurs,

must be isolated from the NORMAL (utility) power

source by means of an approved transfer switch.

Failure to properly isolate the NORMAL and

STANDBY power sources from each other may

result in injury or death to electric utility workers,

due to backfeed of electrical energy.

• Improper or unauthorized installation, operation,

service or repair of the equipment is extremely

dangerous and may result in death, serious per-

sonal injury, or damage to equipment and/or per-

sonal property.

• Extremely high and dangerous power voltages are

present inside an installed transfer switch. Any

contact with high voltage terminals, contacts or

wires will result in extremely hazardous, and pos-

sibly LETHAL, electric shock. DO NOT WORK ON

THE TRANSFER SWITCH UNTIL ALL POWER

VOLTAGE SUPPLIES TO THE SWITCH HAVE

BEEN POSITIVELY TURNED OFF.

• Competent, qualified personnel should install,

operate and service this equipment. Adhere strict-

ly to local, state and national electrical and build-

ing codes. When using this equipment, comply

with regulations the National Electrical Code

(NEC), CSA Standard; C22.1 Canadian Electric

Code and Occupational Safety and Health

Administration (OSHA) have established.

• Never handle any kind of electrical device while

standing in water, while barefoot, or while hands

or feet are wet. DANGEROUS ELECTRICAL

SHOCK MAY RESULT.

DANGER

Important Safety Instructions

Read the following information carefully before attempting to install, operate or service this equip-

ment. Also read the instructions and information on tags, decals, and labels that may be affixed to

the transfer switch. Replace any decal or label that is no longer legible.

DANGER! Connection of a generator to an electrical system normally supplied by an electric utility

shall be by means of suitable transfer equipment so as to isolate the electric system from utility dis-

tribution system when the generator is operating (Article 701 Legally Required Standby Systems or

Article 702 Optional Standby Systems, as applicable). Failure to isolate electric system by these

means may result in damage to generator and may result in injury or death to utility workers due to

backfeed of electrical energy.

Table of Contents

Generac®Power Systems, Inc. 1

Safety Rules..........................................Inside Front Cover

Section 1 — General Information ..................................2

1.1 Introduction ............................................................2

1.2 Equipment Description ..........................................2

1.3 Transfer Switch Data Plate......................................2

1.4 Transfer Switch Enclosure......................................2

1.5 Safe Use Of Transfer Switch....................................2

Section2—Installation ....................................................3

2.1 Introduction to Installation......................................3

2.2 Unpacking ..............................................................3

2.3 Mounting ................................................................3

2.4 Connecting Power Source and Load Lines ..............3

2.4.1 2-Pole Mechanisms ......................................4

2.4.2 3-Pole Mechanisms ......................................4

2.5 Connecting Start Circuit Wires ................................5

2.6 Auxiliary Contacts ..................................................5

2.7 Optional Accessories ..............................................5

Section 3 — Operation..................................................................5

3.1 Functional Tests and Adjustments ..........................6

3.2 Functional Tests ......................................................6

3.3 Manual Operation....................................................6

3.3.1 “V” Type Transfer Switches ..........................6

3.3.2 “Y” Type Transfer Switches ..........................7

3.4 Voltage Checks ........................................................7

3.5 Generator Tests Under Load ..................................8

Section 4 – Notes ..........................................................................9

Section 5 – Wiring Diagrams & Electrical

Schematics ..............................................................10

Section 6 – Exploded Views & Parts Lists ............................14

Section7–Warranty..................................................Back Cover

• Because jewelry conducts electricity, wearing it

may cause dangerous electrical shock. Remove all

jewelry (such as rings, watches, bracelets, etc.)

before working on this equipment.

• If you must work on this equipment while standing

on metal or concrete, place insulative mats over a

dry wood platform. Work on this equipment only

while standing on such insulative mats.

• Never work on this equipment while physically or

mentally fatigued.

• Keep the transfer switch enclosure door closed and

bolted at all times. Only qualified personnel

should be permitted access to the switch interior.

• In case of an accident caused by electric shock,

immediately shut down the source of electrical

power. If this is not possible, attempt to free the

victim from the live conductor but AVOID DIRECT

CONTACT WITH THE VICTIM. Use a nonconduct-

ing implement, such as a rope or board, to free the

victim from the live conductor. If the victim is

unconscious, apply first aid and get immediate

medical help.

• When an automatic transfer switch is installed for

a standby generator set, the generator engine may

crank and start at any time without warning. To

avoid possible injury that might be caused by such

sudden start-ups, the system’s automatic start cir-

cuit must be disabled before working on or around

the generator or transfer switch. For that purpose,

a SAFETY DISCONNECT is provided inside the

transfer switch. Always set that switch to its MAN-

UAL position before working on the equipment.

Then place a “DO NOT OPERATE” tag on the

transfer switch and on the generator.

2 Generac®Power Systems, Inc.

Section 1 — General Information

Generac “V” Type and “Y” Type Transfer Switch

1.1 INTRODUCTION

This manual has been prepared especially for the

purpose of familiarizing personnel with the design,

application, installation, operation and servicing of

the applicable equipment. Read the manual carefully

and comply with all instructions. This will help to

prevent accidents or damage to equipment that might

otherwise be caused by carelessness, incorrect appli-

cation, or improper procedures.

Every effort has been expended to make sure that the

contents of this manual are both accurate and cur-

rent. Generac, however, reserves the right to change,

alter or otherwise improve the product at any time

without prior notice.

1.2 EQUIPMENT DESCRIPTION

The pre-packaged transfer switch is designed to use

with pre-packaged standby generator control panels.

It is used for transferring critical electrical loads from

a NORMAL (utility) power source to a STANDBY

(emergency generator) power source. Such a transfer

of loads occurs automatically when the NORMAL

power source fails or is subsequently reduced and

the STANDBY source voltage and frequency have

reached an acceptable level. The transfer switch pre-

vents electrical feedback between two different power

sources (such as the NORMAL and STANDBY

sources) and, for that reason, codes require it in all

standby electric system installations.

Once the transfer is completed, the STANDBY power

source then powers electrical loads connected to the

transfer switch. When NORMAL source voltage above

an acceptable (preset) level has been restored, circuit

board action in the pre-packaged control panel initi-

ates re-transfer back to NORMAL power source. After

this re-transfer, the circuit board signals to open the

start circuit to the generator, which shuts down the

engine. The circuit board is then "armed" and ready

for the next drop in NORMAL source voltage.

NOTE:

Keep in mind the pre-packaged transfer switch is

without any kind of electronic controls. It receives

signals solely from circuit boards contained in the

prepackaged control panel.

1.3 TRANSFER SWITCH DATA PLATE

Affixed permanently to the transfer switch door is a

DATA PLATE. Use the transfer switch only within the

specific limits shown on the DATA PLATE and on

other decals and labels that may be affixed to the

switch. This prevents damage to equipment, possible

injury to personnel, and provides long and trouble-

free life for the equipment.

When requesting information or ordering parts for

this equipment, make sure to include all information

from the DATA PLATE.

When requesting information or ordering parts for this

equipment, make sure to include all information from

the DATA PLATE.

Record your Model and Serial numbers in the space

provided below for future reference.

1.4 TRANSFER SWITCH ENCLOSURE

The standard switch enclosure is a National

Electrical Manufacturer's Association (NEMA) 1 type.

NEMA 1 type enclosures primarily provide protection

against contact with the enclosed equipment and

against a limited amount of falling dirt.

1.5 SAFE USE OF TRANSFER SWITCH

Before installing, operating or servicing this equip-

ment, read the SAFETY RULES (inside front cover)

carefully. Comply strictly with all SAFETY RULES to

prevent accidents and/or damage to the equipment.

Generac recommends you make a copy of the SAFE-

TY RULES and post them near the transfer switch.

Also, be sure to read all instructions and information

you may find on tags, labels and decals affixed to the

equipment.

Two publications that outline the safe use of transfer

switches are the following:

• National Electrical Code

• UL 1008, STANDARD FOR SAFETY-AUTOMATIC

TRANSFER SWITCHES

MODEL #

SERIAL #

Generac®Power Systems, Inc. 3

2.1 INTRODUCTION TO INSTALLATION

This equipment has been wired and tested at the fac-

tory. Installing the switch includes the following pro-

cedures:

• Mounting the enclosure.

• Connecting power source and load leads.

• Connecting the generator start circuit.

• Installing/connecting any options and accessories.

• Testing functions.

2.2 UNPACKING

Carefully unpack the transfer switch. Inspect closely

for any damage that might have occurred during

shipment. The purchaser must file with the carrier

any claims for loss or damage incurred while in tran-

sit.

Check that all packing material is completely

removed from the switch prior to installation.

Attach any lifting device to the transfer switch mount-

ing holes or brackets only. DO NOT LIFT THE

SWITCH AT ANY OTHER POINT.

2.3 MOUNTING

Transfer switch components are generally mounted

in a standard NEMA 1 type enclosure (Figure 2.1).

Other options are available such as NEMA 34 and

NEMA 12.

Handle transfer switches carefully when

installing. Do not drop the switch. Protect the

switch against impact at all times, and against

construction grit and metal chips. Never install

a transfer switch that has been damaged.

Install the transfer switch as close as possible to the

electrical loads that are to be connected to it. To pre-

vent switch distortion, level all mounting points. If

necessary, use washers behind mounting holes to

level the unit.

2.4 CONNECTING POWER SOURCE

AND LOAD LINES

Make sure to turn OFF both the normal (Utility)

and standby (generator) power supplies before

trying to connect power source and load lines

to the transfer switch. Supply voltages are

extremely high and dangerous. Contact with

such high voltage power supply lines causes

extremely hazardous, possibly lethal, electrical

shock.

Wiring diagrams and electrical schematics are pro-

vided in this manual. Power source and load connec-

tions are made at a transfer mechanism, inside the

switch enclosure.

DANGER

Section2—Installation

Generac “V” Type and “Y” Type Transfer Switch

14.

1.1

MOUNTING DIMENSIONS - 100 AMP

2-POLE UNI

Figure 2.1 — Mounting Dimensions for Enclosures

24.

2.12

NTIN

DIMEN

- 2

& 4

AMP

NIT

4 Generac®Power Systems, Inc.

2.4.1 2-POLE MECHANISMS

These switches (Figures 2.2 and 2.3) are used with a

single phase system, when the single phase NEU-

TRAL line is to be connected to a Neutral Lug and is

not to be switched.

Figure 2.2 — 100 Amp 2-pole Transfer

Mechanism

Figure 2.3 — 200 Amp 2-pole Transfer

Mechanism

2.4.2 3-POLE MECHANISMS

This switch (Figure 2.4) is also used with a single

phase system, when the single phase NEUTRAL line

is to be connected to a Neutral Lug and is not to be

switched.

Figure 2.4 — 3-Pole Transfer Mechanism

Solderless, screw-type terminal lugs are standard.

Conductor sizes must be adequate to handle the max-

imum current to which they will be subjected; based

on the 75°C column of tables, charts, etc. used to size

conductors. The installation must comply fully with

all applicable codes, standards and regulations.

Before connecting wiring cables to terminals, remove

any surface oxides from the cable ends with a wire

brush. If ALUMINUM conductors are used, apply cor-

rosion inhibitor to conductors. After tightening ter-

minal lugs, carefully wipe away any excess corrosion

inhibitor.

All power cables should enter the switch next to

transfer mechanism terminals. Standard terminal

lugs on the transfer mechanism are solderless,

screw-type.

Connect power source load conductors to clearly

marked transfer mechanism terminal lugs as follows

(Figure 2.5 on page 5):

1. Connect NORMAL (utility) power source cables to

switch terminals N1, N2, N3, etc.

2. Connect STANDBY source power cables to trans-

fer switch terminals E1, E2, E3, etc.

3. Connect customer LOAD leads to switch termi-

nals T1, T2, T3, etc.

Conductors must be properly supported, of approved

insulative qualities, protected by approved conduit,

and of the correct wire gauge size in accordance with

applicable codes.

Tighten terminal lugs to the following torques:

100 Amp Switch: 50 INCH-POUNDS

200 Amp Switch: 250 INCH-POUNDS

Make sure to maintain proper electrical 1/2-inch

clearance between live metal parts and grounded

metal.

◆



Section2—Installation

Generac “V” Type and “Y” Type Transfer Switch

Generac®Power Systems, Inc. 5

Section2—Installation

Generac “V” Type and “Y” Type Transfer Switch

2.5 CONNECTING START CIRCUIT

WIRES

Control system interconnections (Figure 2.5) consist

of UTILITY 1 and 2, LOAD 1 and 2; and leads 23 and

194. Control system interconnection leads must be

run in a conduit that is separate from the AC power

lead. Recommended wire gauge sizes for this wiring

depends on the length of the wire, as recommended

below:

NOTE:

The preceding start circuit connections apply to

the standard 2-wire start system only Your transfer

switch may be equipped with a 3-wire connection

system.

2.6 AUXILIARY CONTACTS

If desired, you can access a set of Auxiliary Contacts

on the Transfer Switch to operate customer acces-

sories, remote advisory lights, or remote annunciator

devices. A suitable power source must be connected

to the COMMON (C) terminal. The contacts labeled 1,

2 and 3 (Figure 2.6) are connected at the factory for

operation of transfer switch advisory lights. Contacts

4, 5 and 6 are available for customer use.

Figure 2.6 — Auxiliary Contact Schematic

Auxiliary contacts are rated 15 amperes at 125, 250 or

480 volts AC; 0.5 ampere at 125 volts DC; 0.25 ampere

at 250 volts DC. DO NOT EXCEED THE RATED

VOLTAGE AND CURRENT OF THE CONTACTS.

Contact operation is shown in the following chart:

2.7 OPTIONAL ACCESSORIES

Note any optional accessories that may be installed

on the transfer switch or are to be installed in the

standby electric system in conjunction with the

switch. Complete the necessary connections for these

accessories.

MAXIMUM WIRE LENGTH RECOMMENDED WIRE

SIZE

460 feet (140m) No. 18 AWG.

461 to 730 feet (223m) No. 16 AWG.

731 to 1,160 feet (354m) No. 14 AWG.

1,161 to 1,850 feet (565m) No. 12 AWG.

PEN

WIT

H T

Vac MIN

SWITCH TYPE

SPS

ELECTRICAL RATINGS

TILITY

TRA

NNE

N1 N2 N3

E1 E2 E3

TRA

TRAN

WIT

TILIT

PPL

CUS

AD 2

TILITY 2

TILITY 1

ENERAT

NTR

L PANE

WER LEAD

AND

TRAN

FER

WIT

LEAD

T B

N IN TW

DIFFERENT

E3 AND T3 NO

LE PHA

TEM

AD 1

REMOTE TES

SWITCH

(

OPTIONAL

)

Figure 2.5 — Transfer Switch Interconnections (Drawing #79963-B)

Switch Position

Utility Standby

Common (4) to Normally Closed (6) Closed Open

Common (4) to Normally Closed (5) Open Closed

6 Generac®Power Systems, Inc.

3.1 FUNCTIONAL TESTS AND

ADJUSTMENTS

Following transfer switch installation and intercon-

nection, inspect the entire installation carefully. A

competent, qualified electrician should make the

inspection.

The installation should comply strictly with all appli-

cable codes, standards, laws and regulations. All

electrical connections must be correct and in compli-

ance with applicable codes and standards.

Make sure the standby generator is ready. This

includes checking engine oil level, coolant level, fuel

supply, batteries and other items specified in the

OWNER'S MANUAL for specific generators.

Complete all functional tests as outlined in the FUNC-

TIONAL TESTS section. Do this before placing the

transfer switch into service.

3.2 FUNCTIONAL TESTS

Following transfer switch installation, the entire

standby electric system should be inspected and test-

ed. Have all necessary adjustments completed at this

time. Functional tests of the transfer switch include

these tests: (a) Manual Operation, (b) Voltage Checks

and (c) Electric Operation.

To avoid damaging the transfer switch, perform

functional tests In the exact order given.

Before proceeding with functional tests, read and be

sure you understand all instructions in this section.

Also, read the instructions and information on tags

and decals affixed to the transfer switch. Note any

options and accessories that might be installed or

provided with the switch and review their operation.

DO NOT ATTEMPT MANUAL OPERATION OF THE

TRANSFER SWITCH UNTIL AFTER ALL POWER

VOLTAGE SUPPLIES TO THE SWITCH HAVE BEEN

TURNED OFF. FAILURE TO TURN OFF POWER

VOLTAGE SUPPLIES MAY RESULT IN DANGER-

OUS AND POSSIBLE FATAL ELECTRICAL SHOCK.

3.3 MANUAL OPERATION

The pre-packaged transfer switch has a choice of two

transfer mechanisms - the "V" type (Model 9227-0)

and the "Y" type (Models 9228, 9229 and 9230).

3.3.1 “V” TYPE TRANSFER SWITCHES

Test manual operation for “V” type transfer switches

as follows:

1. Check that the generator's Auto/Off/Manual

switch has been set to OFF position.

2. Turn OFF the UTILITY power supply to the trans-

fer switch, using whatever means provided (such

as the UTILITY source main line circuit breaker).

3. Set the generator's main circuit breaker to its

OFF or OPEN position.

FAILURE TO TURN OFF ALL A POWER VOLTAGE

SUPPLIES TO THE TRANSFER SWITCH BEFORE

ATTEMPTING MANUAL OPERATION RESULTS IN

EXTREMELY HAZARDOUS AND POSSIBLY FATAL

ELECTRICAL SHOCK.

4. Remove the manual transfer handle from the

enclosure.

5. Place open slot of the manual transfer handle on

the small tab of the transfer switch operating

lever (Figure 3.1).

6. Pull manual transfer handle downward, then

move it back to original position. If handle is

down, LOAD is connected to UTILITY power

source. If handle is up, LOAD is connected to

STANDBY power.

7. Move the transfer switch main contacts to both

positions several times. Leave the transfer switch

in the UTILITY position and connect LOAD to the

UTILITY power source (manual operation lever is

up).

Figure 3.1 — Transfer Switch Operation

(“V” Type)

DANGER

◆

DANGER

Section 3 — Operation

Generac “V” Type and “Y” Type Transfer Switch

Generac®Power Systems, Inc. 7

3.3.1 “Y” TYPE TRANSFER SWITCHES

A manual handle was shipped with the transfer

switch. Test manual operation for “Y” type transfer

switches as follows (Figure 3.2):

1. Check that the generator's Auto/Off/Manual

switch has been set to OFF position.

2. Attach the square opening of the manual handle

over the square shaft at lower right corner of

transfer mechanism.

3. Move the manual handle UP. When movement

stops at NEUTRAL, return handle to its original

position and actuate again.

4. Observe the changeover display on transfer

mechanism as follows:

• If utility arrow is aligned with GREEN band, load

is connected to UTILITY (normal) power source.

• If STANDBY arrow is aligned with GREEN band,

LOAD is connected to STANDBY (emergency)

source.

5. Repeat steps 3 and 4 several times, being sure the

switch main contacts actuate normally to all posi-

tions.

6. When certain that switch operates normally, actu-

ate the main contacts to their UTILITY (normal)

source.

NOTE:

LOAD must be connected to UTILITY source

before proceeding. That is, the GREEN BAND

must be next to the UTILITY arrow and the RED

band must be next to the STANDBY arrow.

Figure 3.2 — Manual Operation of “Y” Type

Transfer Switch

3.4 VOLTAGE CHECKS

1. Turn ON the UTILITY power supply to the trans-

fer switch with whatever means provided (such as

the UTILITY maim line circuit breaker).

PROCEED WITH CAUTION. THE TRANSFER

SWITCH IS NOW ELECTRICALLY HOT. CONTACT

WITH LIVE TERMINALS RESULTS IN EXTREMELY

HAZARDOUS AND POSSIBLY FATAL ELECTRICAL

SHOCK.

2. With an accurate AC voltmeter, check for correct

voltage across terminal lugs N1 and N2; N1 to

NEUTRAL; and finally N2 to NEUTRAL (Figure

2.5 on Page 5).

3. When certain that UTILITY supply voltage is correct

and compatible with transfer switch ratings, turn

OFF the UTILITY supply to the transfer switch.

4. On the generator panel, set the Auto/Off/Manual

switch to MANUAL position. The generator

should crank and start.

5. Let the generator stabilize and warm up at no-

load for at least five minutes.

6. Set the generator's main circuit breaker (CBI ) to

its ON or CLOSED position.

PROCEED WITH CAUTION. A GENERATOR OUT-

PUT VOLTAGE IS NOW BEING DELIVERED TO

TRANSFER SWITCH TERMINALS. CONTACT WITH

LIVE TERMINALS RESULTS IN EXTREMELY DAN-

GEROUS AND POSSIBLY FATAL ELECTRICAL

SHOCK.

7. With an accurate AC voltmeter and frequency

meter, check the no-load, voltage and frequency

meter at transfer switch terminal lugs E1, E2 and

NEUTRAL. Readings should be as follows:

a. Frequency ........................61-63 Hz

b. Terminals E1 and E2 ......242-253 volts

c. Terminal E1 to Neutral ....121-126 volts

d. Terminal E2 to Neutral ....121-126 volts

8. Set the generator's main circuit breaker (CBI ) to

its OFF or OPEN position.

9. To shut down the generator, set its

Auto/Off/Manual switch to OFF position.

NOTE:

Do NOT proceed until generator AC output voltage

and frequency are correct and within stated limits.

If the no-load voltage is correct but no-load fre-

quency is incorrect, the engine governed speed

probably requires adjustment. If no-load frequen-

cy is correct but voltage is not, the voltage regula-

tor may require adjustment.

DANGER

◆

Section 3 — Operation

Generac “V” Type and “Y” Type Transfer Switch

8 Generac®Power Systems, Inc.

3.5 GENERATOR TESTS UNDER LOAD

1. Set the generator's main circuit breaker to its

OFF or OPEN position.

2. Manually actuate the transfer switch main con-

tacts to their STANDBY position.

3. To start the generator, set the Auto/Off/Manual

switch to MANUAL. When engine starts, let it sta-

bilize for a few minutes.

4. Turn the generator's main circuit breaker to its

ON or CLOSED position. The generator now pow-

ers all LOAD circuits. Check generator operation

under load as follows:

• Turn ON electrical loads to the full rated

wattage/amperage capacity of the generator. DO

NOT OVERLOAD.

• With maximum rated load applied, check voltage

and frequency across transfer switch terminals

E1 and E2. Voltage should be greater than 230

volts; frequency should be greater than 58 Hz.

• Let the generator run under rated load for at

least 30 minutes. With unit running, listen for

unusual noises, vibration, overheating, etc., that

might indicate a problem.

5. When checkout under load is complete, set main

circuit breaker of the generator to its OFF or

OPEN position.

6. Let the generator run at no-load for several min-

utes. Then, shut down by setting the

Auto/Off/Manual switch to its OFF position.

7. With the manual transfer handle, move the

switch's main contacts back to their utility posi-

tion, i.e., load connected to utility power supply.

Handle and operating lever of transfer switch

should be in down position.

8. Turn on the utility power supply to transfer

switch, using whatever means provided (such as

a utility main line circuit breaker). The utility

power source now powers the loads.

9. Set the generator's Auto/Off/Manual switch to its

AUTO position. The system is now set for fully

automatic operation.

Section 3 — Operation

Generac “V” Type and “Y” Type Transfer Switch

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Cambiar de Generac Power Systems

Generac Power Systems

Generac Power Systems 5464 Manual de usuario

Generac Power Systems

Generac Power Systems RXSW100A3 Manual de usuario

Generac Power Systems

Generac Power Systems RXSW200A3F Manual de usuario

Generac Power Systems

Generac Power Systems RTSN100J3S Manual de usuario

Generac Power Systems

Generac Power Systems GTS "W" Manual de usuario

Generac Power Systems

Generac Power Systems GenTran 6333 Hoja de instrucciones

Generac Power Systems

Generac Power Systems GenTran 6295 Manual de usuario

Generac Power Systems

Generac Power Systems HTS Manual de usuario

Generac Power Systems

Generac Power Systems RTSX100A3 Manual de usuario

Generac Power Systems

Generac Power Systems GenTran 6375 Manual de usuario

Generac Power Systems

Generac Power Systems EZ Switch RTS16EZA1 Manual de usuario

Generac Power Systems

Generac Power Systems PWRview RXEMW200A3 Manual de usuario

Generac Power Systems

Generac Power Systems 004945-1 Manual de usuario

Generac Power Systems

Generac Power Systems TTS Series Manual de usuario

Generac Power Systems

Generac Power Systems RXGW20SHA3 Manual de usuario

Generac Power Systems

Generac Power Systems GenTran 6294 Manual de usuario

Generac Power Systems

Generac Power Systems rtg16eza1 Manual de usuario

Generac Power Systems

Generac Power Systems rtsy100a3 Manual de usuario

Generac Power Systems

Generac Power Systems RXUW200A3 Manual de usuario

Generac Power Systems

Generac Power Systems OG 2697 Hoja de instrucciones

Generac Power Systems

Generac Power Systems Automatic Transfer Switch Manual de usuario

Generac Power Systems

Generac Power Systems GenTran 6294 Manual de usuario

Generac Power Systems

Generac Power Systems RTS Manual de usuario

Generac Power Systems

Generac Power Systems EZ Switch RTS16EZA1 Manual de usuario

Manuales populares de Cambiar de otras marcas

URC

URC Total Control MFS-8 Manual de usuario

Azbil

Azbil HPQ-D11 Manual de usuario

Sony

Sony DFS-900M Manual de usuario

SICK

SICK i17S Manual de usuario

F&F

F&F SZR-277 Manual de usuario

Shure

Shure UAMS/BK Manual de usuario

Dräger

Dräger X-zone Switch Off Manual de usuario

Asco

Asco Joucomatic 349 Series Manual de usuario

BT Mini Hub Manual de usuario

D-Link

D-Link DES-1226G Manual de usuario

Johnson Controls

Johnson Controls FS80-C Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manual de usuario

MicroNet

MicroNet SP1200A Manual de usuario

Ruijie

Ruijie RG-PF2920 Series Manual de instalación y funcionamiento

Altinex

Altinex DA1914SX Manual de usuario

MiLAN

MiLAN MIL-SM2401M Manual de usuario

RJM

RJM MASTERMIND PBC/6X Manual de usuario

Atlas

Atlas MMK-KVM8 Manual de usuario