Generac Power Systems 004635-3 Manual de usuario

Automatic Transfer Switch

Owner’s Manual

ATS “HS” Type

Models: 004635-3

(200 Amp, 250 Volts)

and 004678-2

(100 Amp, 250 Volts)

This manual should remain with the unit.

Generac Power Systems, Inc., hereafter referred to as

the “manufacturer”, cannot anticipate every possible

circumstance that might involve a hazard. The warn-

ings in this manual, and on tags and decals affixed to

the unit are, therefore, not all-inclusive. If using a

procedure, work method or operating technique the

manufacturer does not specifically recommend,

ensure that it is safe for others. Also make sure the

procedure, work method or operating technique cho-

sen does not render the transfer switch unsafe.

Throughout this publication, and on tags and

decals affixed to the generator, DANGER, WARNING,

CAUTION and NOTE blocks are used to alert per-

sonnel to special instructions about a particular

operation that may be hazardous if performed incor-

rectly or carelessly. Observe them carefully. Their def-

initions are as follows:

After this heading, read instructions that, if not

strictly complied with, will result in personal

injury, including death, or property damage.

After this heading, read instructions that, if not

strictly complied with, may result in personal injury

or property damage.

After this heading, read instructions that, if not

strictly complied with, could result in damage to

equipment and/or property.

NOTE:

After this heading, read explanatory statements

that require special emphasis.

These safety warnings cannot eliminate the hazards

that they indicate. Common sense and strict compli-

ance with the special instructions while performing the

service are essential to preventing accidents.

Four commonly used safety symbols accompany the

DANGER, WARNING and CAUTION blocks. The type

of information each indicates follows:

This symbol points out important safety informa-

tion that, if not followed, could endanger personal

safety and/or property.

This symbol points out potential explosion hazard.

This symbol points out potential fire hazard.

This symbol points out potential electrical shock

hazard.

GENERAL HAZARDS

• Any AC generator that is used for backup power if

a NORMAL (UTILITY) power source failure occurs,

must be isolated from the NORMAL (UTILITY)

power source by means of an approved transfer

switch. Failure to properly isolate the NORMAL

and STANDBY power sources from each other may

result in injury or death to electric utility workers,

due to backfeed of electrical energy.

• Improper or unauthorized installation, operation,

service or repair of the equipment is extremely

dangerous and may result in death, serious per-

sonal injury, or damage to equipment and/or per-

sonal property.

• Extremely high and dangerous power voltages are

present inside an installed transfer switch. Any

contact with high voltage terminals, contacts or

wires will result in extremely hazardous, and pos-

sibly LETHAL, electric shock. DO NOT WORK ON

THE TRANSFER SWITCH UNTIL ALL POWER

VOLTAGE SUPPLIES TO THE SWITCH HAVE

BEEN POSITIVELY TURNED OFF.

• Competent, qualified personnel should install,

operate and service this equipment. Adhere strict-

ly to local, state and national electrical and build-

ing codes. When using this equipment, comply

with regulations the National Electrical Code

(NEC), CSA Standard; C22.1 Canadian Electric

Code and Occupational Safety and Health

Administration (OSHA) have established.

• Never handle any kind of electrical device while

standing in water, while barefoot, or while hands

or feet are wet. DANGEROUS ELECTRICAL

SHOCK MAY RESULT.

DANGER

IMPORTANT SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS! Read the following information carefully before attempting to

install, operate or service this equipment. Also read the instructions and information on tags,

decals, and labels that may be affixed to the transfer switch. Replace any decal or label that

is no longer legible.

DANGER! Connection of a generator to an electrical system normally supplied by an electric

utility shall be by means of suitable transfer equipment so as to isolate the electric system

from utility distribution system when the generator is operating (Article 701 Legally Required

Standby Systems or Article 702 Optional Standby Systems, as applicable). Failure to isolate

electric system by these means may result in damage to generator and may result in injury

or death to utility workers due to backfeed of electrical energy.

Table of Contents

Safety Rules..........................................Inside Front Cover

Section 1 — General Information ..................................2

1.1 Introduction ............................................................2

1.2 Equipment Description ............................................2

1.3 Transfer Switch Data Decal......................................2

1.4 Transfer Switch Enclosure ......................................2

1.5 Safe Use Of Transfer Switch ....................................2

Section 2 — Installation ....................................................3

2.1 Introduction to Installation ......................................3

2.2 Unpacking ................................................................3

2.3 Mounting ..................................................................3

2.4 Connecting Power Source and Load Lines................3

2.4.1 2-Pole Mechanism ..........................................3

2.5 Connecting Start Circuit Wires ................................4

Section 3 — Operation ......................................................4

3.1 Functional Tests & Adjustments ..............................4

3.2 Manual Operation ....................................................4

3.2.1 Close to Normal Source Side ........................4

3.2.2 Close to Emergency Source Side....................5

3.2.3 Return to Normal Source Side ......................5

3.3 Voltage Checks..........................................................5

3.4 Generator Tests Under Load ....................................6

Section 4 – Notes................................................................7

Section 5 – Installation Diagram..................................10

Section 6 – Electrical Data ............................................11

Section 7 – Exploded Views & Parts Lists ..................14

Section 8 – Warranty/Service........................Back Cover

• Remove all jewelry (such as rings, watches,

bracelets, etc.) before working on this equipment.

• If work must be done on this equipment while

standing on metal or concrete, place insulative

mats over a dry wood platform. Work on this

equipment only while standing on such insulative

mats.

• Never work on this equipment while physically or

mentally fatigued.

• Keep the transfer switch enclosure door closed and

bolted at all times. Only qualified personnel

should be permitted access to the switch interior.

• In case of an accident caused by electric shock,

immediately shut down the source of electrical

power. If this is not possible, attempt to free the

victim from the live conductor but AVOID DIRECT

CONTACT WITH THE VICTIM. Use a nonconduct-

ing implement, such as a dry rope or board, to free

the victim from the live conductor. If the victim is

unconscious, apply first aid and get immediate

medical help.

• When an automatic transfer switch is installed for

a standby generator set, the generator engine may

crank and start at any time without warning. To

avoid possible injury that might be caused by such

sudden start-ups, the system’s automatic start cir-

cuit must be disabled before working on or around

the generator or transfer switch. Then place a “DO

NOT OPERATE” tag on the transfer switch and on

the generator. Remove the Negative (Neg) or (–) bat-

tery cable.

For authorized service,

reference the dealer locator

number found inside the

generator owner’s manual.

Section 1 — General Information

ATS “HS” Type Transfer Switch

1.1 INTRODUCTION

This manual has been prepared especially for the

purpose of familiarizing personnel with the design,

application, installation, operation and servicing of

the applicable equipment. Read the manual carefully

and comply with all instructions. This will help to

prevent accidents or damage to equipment that might

otherwise be caused by carelessness, incorrect appli-

cation, or improper procedures.

Every effort has been expended to make sure that the

contents of this manual are both accurate and cur-

rent. The manufacturer, however, reserves the right

to change, alter or otherwise improve the product at

any time without prior notice.

1.2 EQUIPMENT DESCRIPTION

The automatic transfer switch is used for transfer-

ring electrical load from a UTILITY (NORMAL) power

source to a EMERGENCY ( STANDBY) power source.

Such a transfer of electrical loads occurs automati-

cally when the UTILITY power source has failed or is

substantially reduced and the EMERGENCY source

voltage and frequency have reached an acceptable

level. The transfer switch prevents electrical feedback

between two different power sources (such as the

UTILITY and EMERGENCY sources) and, for that

reason, codes require it in all standby electric system

installations.

The transfer switch consists of a transfer mecha-

nism, a relay control, and a terminal strip for con-

nection of sensing wires.

This switch is suitable for control of motors, electric

discharge lamps, tungsten filament and electric heat-

ing equipment and the tungsten load does the switch

rating.

The transfer switch is for use in optional standby sys-

tems only.

The transfer switch is suitable for use on a circuit

capable of 10,000 rms symmetrical amperes, 240

VAC when protected by a circuit breaker without an

adjustable short time response or by fuses.

1.3 TRANSFER SWITCH DATA DECAL

A DATA DECAL is permanently affixed to the transfer

switch enclosure. Use this transfer switch only with

the specific limits shown on the DATA DECAL and on

other decals and labels that may be affixed to the

switch. This will prevent damage to equipment and

property.

When requesting information or ordering parts for this

equipment, make sure to include all information from

the DATA DECAL.

Record the Model and Serial numbers in the space pro-

vided below for future reference.

1.4 TRANSFER SWITCH ENCLOSURE

The standard switch enclosure is a National

Electrical Manufacturer’s Association (NEMA) 3R

type. NEMA 3R type enclosures primarily provide a

degree of protection against falling rain and sleet and

is not damaged by the formation of ice on the

enclosure.

1.5 SAFE USE OF TRANSFER SWITCH

Before installing, operating or servicing this equip-

ment, read the SAFETY RULES (inside front cover)

carefully. Comply strictly with all SAFETY RULES to

prevent accidents and/or damage to the equipment.

The manufacturer recommends that a copy of the

SAFETY RULES are posted near the transfer switch.

Also, be sure to read all instructions and information

found on tags, labels and decals affixed to the equip-

ment.

Two publications that outline the safe use of transfer

switches are the following:

• NFPA 70; National Electrical Code

• UL 1008, STANDARD FOR SAFETY-AUTOMATIC

TRANSFER SWITCHES

MODEL #

SERIAL #

2.1 INTRODUCTION TO INSTALLATION

This equipment has been wired and tested at the fac-

tory. Installing the switch includes the following pro-

cedures:

• Mounting the enclosure.

• Connecting power source and load leads.

• Connecting the generator start circuit.

• Connecting any auxiliary contact (if needed)

• Testing functions.

2.2 UNPACKING

Carefully unpack the transfer switch. Inspect closely

for any damage that might have occurred during ship-

ment. The purchaser must file with the carrier any

claims for loss or damage incurred while in transit.

Check that all packing material is completely

removed from the switch prior to installation.

2.3 MOUNTING

Mounting dimensions for the transfer switch enclo-

sure are in this manual. Enclosures are typically

wall-mounted. See “Installation Diagram”, Section 5.

Handle transfer switches carefully when

installing. Do not drop the switch. Protect the

switch against impact at all times, and against

construction grit and metal chips. Never

install a transfer switch that has been dam-

aged.

Install the transfer switch as close as possible to the

electrical loads that are to be connected to it. Mount

the switch vertically to a rigid supporting structure.

To prevent switch distortion, level all mounting

points. If necessary, use washers behind mounting

holes to level the unit.

2.4 CONNECTING POWER SOURCE

AND LOAD LINES

Make sure to turn OFF both the UTILITY

(NORMAL) and EMERGENCY (STANDBY)

power supplies before trying to connect

power source and load lines to the transfer

switch. Supply voltages are extremely high

and dangerous. Contact with such high volt-

age power supply lines will result in an

extremely hazardous, possibly lethal, electri-

cal shock.

Wiring diagrams and electrical schematics are pro-

vided in this manual. Power source and load connec-

tions are made at a transfer mechanism, inside the

switch enclosure.

2.4.1 2-POLE MECHANISM

These switches (Figure 2.1) are used with a single-

phase system, when the single-phase NEUTRAL line

is to be connected to a Neutral Lug and is not to be

switched.

Figure 2.1 — Typical 2-Pole Transfer Mechanism

(200 Amp Shown)

Solderless, screw-type terminal lugs are standard.

Conductor sizes must be adequate to handle the max-

imum current to which they will be subjected to,

based on the 75°C column of tables, charts, etc. used

to size conductors. The installation must comply fully

with all applicable codes, standards and regulations.

Before connecting wiring cables to terminals, remove

any surface oxides from the cable ends with a wire

brush. All power cables should enter the switch next

to transfer mechanism terminals. If ALUMINUM con-

ductors are used, apply corrosion inhibitor to con-

ductors. Tighten terminal lugs to the torque values as

noted on the decal located on the inside of the door.

After tightening terminal lugs, carefully wipe away

any excess corrosion inhibitor.

All power cables should enter the switch next to the

transfer mechanism terminals.

Use a torque wrench to tighten the conduc-

tors, being sure not to over tighten, or dam-

age to the switch base could occur. If not

tightened enough, a loose connection would

result, causing excess heat which could dam-

age the switch base.

UTILITY

CLOSING

COIL

GENERATOR

CLOSING

COIL

UTILITY LUGS

GENERATOR

LUGS (E1 & E2)

LOAD LUGS (T1 & T2)



DANGER

Section 2 — Installation

GTS “HS” Type Transfer Switch

Switch Wire Conductor Tightening

Rating Range Torque

100A #14-1/0 AWG 50 in-lbs.

200A #6-250 MCM 275 in-lbs.

Section 3 — Operation

ATS “HS” Type Transfer Switch

Connect power source load conductors to clearly

marked transfer mechanism terminal lugs as follows

1. Connect UTILITY (NORMAL) power source cables

to switch terminals N1, N2.

2. Connect EMERGENCY (STANDBY) source power

cables to transfer switch terminals E1, E2.

3. Connect customer LOAD leads to switch termi-

nals T1, T2.

Conductors must be properly supported, of approved

insulative qualities, protected by approved conduit,

and of the correct wire gauge size in accordance with

applicable codes.

Be sure to maintain proper electrical clearance

between live metal parts and grounded metal. Allow

at least 1/2 inch for 100-400 amp circuits.

2.5 CONNECTING START CIRCUIT

WIRES

Control system interconnections (Section 6) consist

of UTILITY 1 (N1) and UTILITY 2 (N2), LOAD 1 (T1)

and LOAD 2 (T2), and leads 23 and 194 when used

in conjunction with some water-cooled generators.

Recommended wire gauge sizes for this wiring

depends on the length of the wire, as recommended

below:

NOTE:

If there are no matching terminal connections for

LOAD 1 (T1) and LOAD 2 (T2) in the generator

control panel, do not connect these wires. Failure

of the control board will occur if connected.

3.1 FUNCTIONAL TESTS AND

ADJUSTMENTS

Following transfer switch installation and inter-

connection, inspect the entire installation careful-

ly. A competent, qualified electrician should

inspect it. The installation should comply strictly

with all applicable codes, standards, and regula-

tions. When absolutely certain the installation is

proper and correct, complete a functional test of

the system.

Perform functional tests in the exact order

presented in this manual, or damage could be

done to the switch.

IMPORTANT: Before proceeding with functional

tests, read and make sure all instructions and infor-

mation in this section are understood. Also read the

information and instructions of labels and decals

affixed to the switch. Note any options or accessories

that might be installed and review their operation.

3.2 MANUAL OPERATION

Do NOT manually transfer under load.

Disconnect transfer switch from all power

sources by approved means, such as a main

circuit breaker(s).

A manual HANDLE is shipped with the transfer

switch. Manual operation must be checked BEFORE

the transfer switch is operated electrically. To check

manual operation, proceed as follows:

1. Turn the generator’s AUTO-OFF-MANUAL switch

to OFF.

2. Turn OFF both UTILITY and EMERGENCY

power supplies to the transfer switch, with what-

ever means provided (such as the main line cir-

cuit breakers).

3. Note position of transfer mechanism main con-

tacts by observing the moveable contact carrier

arm.

• Manual operation handle towards the top of

switch mechanism - LOAD terminals (T1, T2) are

connected to UTILITY terminals (N1, N2).

• Manual operation handle towards the bottom of

switch mechanism - LOAD terminals (T1, T2) are

connected to EMERGENCY terminals (E1, E2).

Do not use excessive force when operating

the transfer switch manually or damage could

be done to the manual handle.

3.2.1 CLOSE TO NORMAL SOURCE SIDE

Before proceeding, verify the position of the switch by

observing the position of manual operation handle in

Figure 3.1. If the handle is UP, the contacts are closed

in the NORMAL position, no further action is

required. If the handle is DOWN, proceed with Step

Step 1: With the handle inserted into the actuating

shaft, move handle UP. Be sure to hold on to

the handle as it will move quickly after the

center of travel.

◆

DANGER

MAXIMUM WIRE LENGTH RECOMMENDED WIRE

SIZE

460 feet (140m) No. 18 AWG.

461 to 730 feet (223m) No. 16 AWG.

731 to 1,160 feet (354m) No. 14 AWG.

1,161 to 1,850 feet (565m) No. 12 AWG.

3.2.2 CLOSE TO EMERGENCY SOURCE SIDE

Before proceeding, verify the position of the switch by

observing the position of the manual operation han-

dle in Figure 3.1. If the handle is DOWN, the contacts

are closed in the EMERGENCY (STANDBY) position.

No further action is required. If the handle is UP, pro-

ceed with Step 1.

Step 1: With the handle inserted into the actuating

shaft, move the handle DOWN. Be sure to

hold on to the handle as it will move quickly

after the center of travel.

3.2.3 RETURN TO NORMAL SOURCE SIDE

Manually actuate switch to return manual operating

handle to the UP position.

3.3 VOLTAGE CHECKS

1. Turn ON the UTILITY power supply to the trans-

fer switch with whatever means provided (such as

the UTILITY main line circuit breaker).

PROCEED WITH CAUTION. THE TRANSFER

SWITCH IS NOW ELECTRICALLY HOT. CONTACT

WITH LIVE TERMINALS RESULTS IN EXTREMELY

HAZARDOUS AND POSSIBLY FATAL ELECTRI-

CAL SHOCK.

2. With an accurate AC voltmeter, check for correct

voltage.

Single-phase utility supply:

Measure across ATS terminal lugs N1 and N2.

Also check N1 to NEUTRAL and N2 to NEUTRAL.

3. When certain that UTILITY supply voltage is cor-

rect and compatible with transfer switch ratings,

turn OFF the UTILITY supply to the transfer

switch.

4. On the generator panel, set the AUTO-OFF-

MANUAL switch to MANUAL position. The gener-

ator should crank and start.

5. Let the generator stabilize and warm up at no-

load for at least five minutes.

6. Set the generator's main circuit breaker (CB1) to

its ON or CLOSED position.

DANGER

◆

Section 3 — Operation

ATS “HS” Type Transfer Switch

Attach handle to actuating shaft.

Move handle

UP for the

NORMAL

(UTILITY)

position.

Move handle

DOWN for the

EMERGENCY

(STANDBY)

position.

NOTE: Return handle to

storage position in enclosure

when finished with manual transfer.

Figure 3.1 — Actuating Transfer Switch

PROCEED WITH CAUTION. GENERATOR OUT-

PUT VOLTAGE IS NOW BEING DELIVERED TO

TRANSFER SWITCH TERMINALS. CONTACT

WITH LIVE TERMINALS RESULTS IN EXTREMELY

DANGEROUS AND POSSIBLY FATAL ELECTRI-

CAL SHOCK.

7. With an accurate AC voltmeter and frequency

meter, check the no-load, voltage and frequency.

Single-phase generator supply:

Measure across ATS terminal lugs E1 to E2. Also

check E1 to NEUTRAL and E2 to NEUTRAL.

a. Frequency ......................................60-62 Hertz

b. Terminals E1 to E2 ........................240-246 VAC

c. Terminals E1 to NEUTRAL ............120-123 VAC

d. Terminals E2 to NEUTRAL ............120-123 VAC

8. Set the generator’s main circuit breaker (CB1) to

its OFF or OPEN position.

9. Set the AUTO/OFF/MANUAL switch to the OFF

position to shut down the generator.

NOTE:

Do NOT proceed until generator AC output voltage

and frequency are correct and within stated limits.

If the no-load voltage is correct but no-load fre-

quency is incorrect, the engine governed speed

probably requires adjustment. If no-load frequen-

cy is correct but voltage is not, the voltage regula-

tor may require adjustment.

3.4 GENERATOR TESTS UNDER LOAD

1. Set the generator's main circuit breaker to its

OFF or OPEN position.

2. Manually actuate the transfer switch main con-

tacts to their EMERGENCY (STANDBY) position.

Refer to Manual Operation (Section 3.2).

3. To start the generator, set the AUTO-OFF-

MANUAL switch to MANUAL. When engine starts,

let it stabilize for a few minutes.

4. Turn the generator's main circuit breaker to its

ON or CLOSED position. The generator now pow-

ers all LOAD circuits. Check generator operation

under load as follows:

• Turn ON electrical loads to the full rated

wattage/amperage capacity of the generator.

DO NOT OVERLOAD.

• With maximum rated load applied, check

voltage and frequency across transfer switch

terminals E1 and E2. Voltage should be

greater than 230 volts and frequency should

be greater than 59 Hertz.

• Let the generator run under rated load for at

least 30 minutes. With unit running, listen for

unusual noises, vibration, overheating, etc.,

that might indicate a problem.

5. When checkout under load is complete, set main

circuit breaker of the generator to its OFF or

OPEN position.

6. Let the generator run at no-load for several

minutes. Then, shut down by setting the AUTO-

OFF-MANUAL switch to its OFF position.

7. Move the switch's main contacts back to their

UTILITY position. For example, load connected to

UTILITY power supply. Refer to Manual

Operation (Section 3.2). Handle and operating

lever of transfer switch should be in UP position.

8. Turn on the UTILITY power supply to transfer

switch, using whatever means provided (such as

a UTILITY main line circuit breaker). The UTILI-

TY power source now powers the loads.

9. Set the generator's AUTO-OFF-MANUAL switch to

its AUTO position. The system is now set for fully

automatic operation.

DANGER

Section 3 — Operation

ATS “HS” Type Transfer Switch

Section 4 — Notes

ATS “HS” Type Transfer Switch

Section 4 — Notes

ATS “HS” Type Transfer Switch

Otros manuales para 004635-3

Tabla de contenidos

Otros manuales de Cambiar de Generac Power Systems

Generac Power Systems

Generac Power Systems EZ Switch RTS16EZA1 Manual de usuario

Generac Power Systems

Generac Power Systems 4678-1 Manual de usuario

Generac Power Systems

Generac Power Systems GenTran 6333 Hoja de instrucciones

Generac Power Systems

Generac Power Systems GenTran 6375 Hoja de instrucciones

Generac Power Systems

Generac Power Systems 09227-0 Manual de usuario

Generac Power Systems

Generac Power Systems GenTran 6294 Manual de usuario

Generac Power Systems

Generac Power Systems ILC Manual de usuario

Generac Power Systems

Generac Power Systems CTTS Series Manual de usuario

Generac Power Systems

Generac Power Systems OG 2697 Hoja de instrucciones

Generac Power Systems

Generac Power Systems PWRview RXEMW200A3 Manual de usuario

Generac Power Systems

Generac Power Systems 004635-3 Manual de usuario

Generac Power Systems

Generac Power Systems rtsy100a3 Manual de usuario

Generac Power Systems

Generac Power Systems GenTran 6375 Manual de usuario

Generac Power Systems

Generac Power Systems 5464 Manual de usuario

Generac Power Systems

Generac Power Systems RXSW100A3 Manual de usuario

Generac Power Systems

Generac Power Systems RTSR600A3 Manual de usuario

Generac Power Systems

Generac Power Systems GTS Series Manual de usuario

Generac Power Systems

Generac Power Systems GenTran 6294 Manual de usuario

Generac Power Systems

Generac Power Systems RTSX100A3 Manual de usuario

Generac Power Systems

Generac Power Systems TMS200 Manual de usuario

Generac Power Systems

Generac Power Systems HTS Wn Manual de usuario

Generac Power Systems

Generac Power Systems GenTran 6295 Manual de usuario

Generac Power Systems

Generac Power Systems TRANSFER SWITCH Manual de instrucciones

Generac Power Systems

Generac Power Systems EZ Switch RTS16EZA1 Manual de usuario

Manuales populares de Cambiar de otras marcas

URC

URC Total Control MFS-8 Manual de usuario

Azbil

Azbil HPQ-D11 Manual de usuario

Sony

Sony DFS-900M Manual de usuario

SICK

SICK i17S Manual de usuario

F&F

F&F SZR-277 Manual de usuario

Shure

Shure UAMS/BK Manual de usuario

Dräger

Dräger X-zone Switch Off Manual de usuario

Asco

Asco Joucomatic 349 Series Manual de usuario

BT Mini Hub Manual de usuario

D-Link

D-Link DES-1226G Manual de usuario

Johnson Controls

Johnson Controls FS80-C Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manual de usuario

MicroNet

MicroNet SP1200A Manual de usuario

Ruijie

Ruijie RG-PF2920 Series Manual de instalación y funcionamiento

Altinex

Altinex DA1914SX Manual de usuario

MiLAN

MiLAN MIL-SM2401M Manual de usuario

RJM

RJM MASTERMIND PBC/6X Manual de usuario

Atlas

Atlas MMK-KVM8 Manual de usuario