Generac Power Systems 1300PSI Manual de usuario
1300PSI
The Reliable Ones
High Pressure Washer
Owner’s Manual
Problems?
Questions?
Before taking your unit
back to the store,
call the pressure washer
helpline at
1-800-2 0-1408
M-F 8-5 CST
GENERAC
This symbol points out important safety instructions, which, if not followed, could endan-
ger the personal safety and/or property of yourself and others. Read and follow all
instructions in the manual before attempting to operate this unit.
Model No. 0 (1300 PSI High Pressure Washer) Manual No. B2351 Revision 0 (12/16/9 )
CAUTION! Read all instructions
before using this product to reduce
the risk of injury.
DANGER! Risk of electrocution!
Inspect cord before every use. Do not use if cord is
damaged.
Keep all connections dry and off the ground.
Do not touch plug with wet hands.
Double-insulated When servicing, use only iden-
tical replacement parts.
his product shall only be connected to a power
supply receptacle protected by a Ground Fault Cir-
cuit Interrupter (GFCI).
Read instruction manual before using.
WARNING! To reduce the risk of
injury, close supervision is neces-
sary when product is used near
children.
Know how to stop the product and bleed the pres-
sure quickly. Be thoroughly familiar with controls.
Stay alert. Watch what you are doing.
Do not operate the product when fatigued or under
the influence of alcohol or drugs.
Keep operating area clear of all persons.
WARNING! Risk of injury or injection
to persons Do not discharge
stream at persons or animals.
High pressure hose can develop leaks from wear,
kinking, abuse, etc. Water spraying from a leak is
capable of injecting material into skin. Do not point
the pressure washer spray at people or animals.
Do not overreach or stand on unstable support.
Keep good footing and balance at all times.
Follow the maintenance instructions specified in the
manual.
his product shall only be connected to a power
supply receptacle protected by a Ground Fault Cir-
cuit Interrupter (GFCI). his is done to comply with
National Electrical Code (NFPA 70) and to provide
additional protection from risk of electrical shock.
Save these instructions.
Operate this pressure washer only in areas away
from combustible materials, combustible fumes or
dust.
Some chemicals or detergents may be harmful if
inhaled or ingested, causing severe nausea, faint-
ing or poisoning. he harmful elements may cause
property damage or severe injury.
Do not allow CHILDREN to operate the Pressure
Washer at any time.
Before starting the Pressure Washer in cold
weather, check all parts of the equipment and be
sure ice has not formed.
Units with broken or missing parts, or without pro-
tective housing or covers should NEVER be
operated.
DANGER! Risk of Explosion Do
not spray flammable liquids.
Never aim the gun at people, animals or plants.
For household use. For indoor or outdoor use.
High pressure stream of fluid that this equipment
can produce may pierce skin and its underlying tis-
sues, leading to serious injury and possible
amputation.
High pressure spray can cause paint chips or other
particles to become airborne and fly at high speeds.
Always wear eye protection when you use this
equipment or when you are in vicinity where the
equipment is in use.
2
High Pressure Washer
GENERAC
Generac 1300PSI Electric High Pressure Washer
Save these instructions
IMPORTANT! SAFETY INSTRUCTIONS IMPORTANT!
3
High Pressure Washer
GENERAC
Generac 1300PSI Electric High Pressure Washer
Never move the machine by pulling on high pres-
sure hose. Use the handle provided on the top of
the unit.
Use a respirator or mask whenever there is a
chance that vapors may be inhaled. Read all
instructions with the mask so you are certain the
mask will provide the necessary protection against
inhaling harmful vapors.
High pressure spray may damage fragile items
including glass. Do not point spray gun at glass
when in the high pressure mode.
Keep the hose connected to machine or the spray
gun while the system is pressurized. Disconnecting
the hose while the unit is pressurized is dangerous.
Hold the spray gun firmly in your hand before you
start the unit. Do not leave the pressure washer
unattended while the machine is turned on.
Cleaning area should have adequate slopes and
drainage to reduce possibility of a fall due to slip-
pery surfaces.
Keep water spray away from electric wiring or fatal
electric shock may result.
Do not by-pass any safety device on this machine.
Operate and store this unit on a stable surface.
Inspect hose each time before using it. Check all
hoses for cuts, leaks, abrasions, bulging of cover,
damage or movement of couplings. If any of these
conditions exist, replace hose immediately. Never
repair high pressure hose. Replace it with another
hose that meets minimum pressure rating of your
pressure washer.
Store in a clean, dry area. Ideally, the unit should be
stored in a frost-free room.
Servicing of a Double Insulated Product.
In a double-insulated product, two systems of insula-
tion are provided instead of grounding. No means of
grounding is provided on a double-insulated product,
nor should a means for grounding be added.
Servicing a double-insulated product requires extreme
care and knowledge of the system and should be
done only by qualified service personnel. Replace-
ment parts for a double-insulated product must be
identical to the parts they replace. Use only genuine
replacement parts. A double-insulated product is
marked with the words DOUBLE INSULA ION or
DOUBLE INSULA ED.
he symbol may also be marked on the product.
Extension Cords
Use only extension cords that are approved for out-
side use. hese extension cords are identified by a
marking ACCEP ABLE FOR USE WI H OU DOOR
APPLIANCES; S ORE INDOORS WHILE NO IN
USE. Use only extension cords having an electrical
rating greater than the rating of the product. Do not
use damaged extension cords. Examine extension
cord before using and replace if damaged. Do not
abuse extension cord and do not yank on any cord to
disconnect it. Keep cord away from heat and sharp
edges. Always disconnect the extension cord from the
receptacle before disconnecting the pressure washer
from the extension cord.
Save these instructions
IMPORTANT! SAFETY INSTRUCTIONS IMPORTANT!
4
High Pressure Washer
CONGRATULATIONS on your purchase of a GEN-
ERAC electric high pressure washer. It has been
designed, engineered and manufactured to give you
the best possible dependability and performance.
Should you experience any problem you cannot easily
remedy, please contact your nearest GENERAC
Authorized Service facility, or call the
18002 01408 number listed on the front of this
manual. We have competent, well-trained technicians
and the proper tools to service or repair this unit.
Please read and retain this manual. he instructions
will enable you to assemble and maintain your high
pressure washer properly. Always observe the
SAFE Y RULES.
CUSTOMER RESPONSIBILITIES
Read and observe the safety rules.
Follow regular schedule in maintaining, caring for
and using your high pressure washer.
Follow the instructions under Maintenance and
Storage sections of this Owner's Manual.
PRODUCT SPECIFICATIONS
Pressure Washer Specifications
Pressure 1300 pounds per square inch
(PSI)
Flow Rate 1.5 gallons per minute (GPM)
Detergent Mix Use Undiluted Detergent
Water Supply Inlet water not to exceed
Temperature 104°F
Motor Brush ype (Universal)
Rated Voltage 120 Volts
Current 14 Amperes
Read these instructions and Operators Manual in its
entirety before you attempt to assemble or operate
your new high pressure washer. Your high pressure
washer has, for the most part, been assembled at the
factory. Before you can operate your new high pres-
sure washer, you must properly connect the high
pressure hose and the water supply.
If you have any problems with the assembly of your
pressure washer, please call the pressure washer
helpline at 1-800-2 0-1408.
GENERAC
Generac 1300PSI Electric High Pressure Washer
Model
Number 07770
Serial
Number_________________________________
Date of
Purchase________________________________
he model and serial numbers will be found on a
decal attached to the pressure washer. You
should record both serial number and date of pur-
chase and keep in a safe place for future
reference
GENERAC
Generac 1300PSI High Pressure Washer
5
High Pressure Washer
Spray Gun Controls the application of water onto
cleaning surface with trigger device. Includes safety
latch.
High Pressure Outlet Connection for high pres-
sure hose.
Master On/Off Switch his switch ONLY enables
the Grip Start system to function.
Grip Start System Pressing and releasing the
spray gun trigger starts and stops the electric motor in
the pressure washer.
Safety Flow System Electric motor will not start
unless water is supplied to the pump.
Foamer Used to apply detergent. Mixes water
and detergent in outlet water flow.
Bayonet Adapter (Not Shown) Connector accom-
modates the connection of a utility and rotating brush
to the spray gun.
Water Inlet Connection for garden hose. (Note:
You need to use the quickconnect to attach the
garden hose to the pressure washer)
Nozzle Lance Attaches to spray gun and accom-
modates the adjustable and turbo nozzles.
Rotating Brush Attaches to the spray gun with the
bayonet adapter. Automatically scrubs surfaces when
trigger is engaged.
Utility Brush Attaches to the spray gun with the
bayonet adapter. Use this brush to scrub a variety of
surfaces.
Turbo Nozzle Attaches to the nozzle lance.
Expands the high pressure stream to allow for high
pressure cleaning of larger areas.
Adjustable Nozzle urn nozzle clockwise for
narrow spray and counterclockwise for fan spray.
Read this owners manual before operating your high pressure washer. Compare the illustrations with your
high pressure washer to familiarize yourself with the locations of various controls and adjustments. Save this
manual for future reference.
Spray Gun
Master On/Off Switch
High Pressure Outlet
High Pressure Hose
Adjustable Nozzle
Extension
Nozzle Lance
Water Inlet
Grip Start System
Rotating Brush Utility Brush
Turbo Nozzle
Safety Flow System
Foamer
6
High Pressure Washer
GENERAC
Generac 1300PSI Electric High Pressure Washer
CARTON CONTENTS
Items in the carton include:
Main Unit
Cart Box (which includes instructions and hardware
to assemble the cart)
Parts Box (which includes the following):
Goggles
Owners Manual
Spray Gun
Nozzle Lance
Foamer
Rotary Brush
urbo Nozzle
Utility Brush
High Pressure Hose
Parts Bag (which includes the following):
Nozzle Cleaning Kit
Bayonet adapter, must be used to attach the
brushes to the gun.
Quick Connect (male and female ends)
Refer to the above list for an illustrated listing of all
items included with your pressure washer. Become
familiar with each piece before assembling the pres-
sure washer. Check all contents against list. If any
parts are missing, call the pressure washer helpline at
1-800-2 0-1408.
HOW TO SET UP YOUR PRES-
SURE WASHER
Follow the instructions in the cart box to assemble
the cart and install it onto the main unit.
Unwind the high pressure hose and attach it to
spray gun (Figure 1).
Attach the high pressure hose to the high pressure
outlet and tighten by hand (Figure 2).
Included with this unit is a quick-connect fitting that
you must attach to the water inlet and your garden
hose. You can install the grey male connector by
hand but you may need to use an adjustable
wrench to tighten it (Figure 3).
Check the screen on the female connector. Make
sure it is clean and check for damage. If you see
any damage in the screen, do not use that female
connector.
Attach the female quick connect to your garden
hose.
Attach garden hose to the water inlet using the
quickconnect. he quickconnect should lock in
place. (Figure 4 on page 7).
AASSSSEEMMBBLLYY
Figure 1 — Attach High Pressure Hose to Spray
Gun.
Figure 2 — Attach High Pressure Hose to Main
Unit.
Figure 3 — Install Quick–Connect
Connect high pressure
hose here
Male QuickConnect
Female QuickConnect
Generac 1300PSI Electric High Pressure Washer
7
High Pressure Washer
GENERAC
DANGER: When connecting the unit to a
power supply receptacle, use ONLY a
receptacle protected by a Ground Fault Cir-
cuit Interrupter (GFCI). This will help
protect against electrical shock.
CAUTION: Before starting you should be
sure the electrical supply is rated at 120
volts, 15 amps.
WARNING: To reduce the risk of electrocu-
tion, keep ALL connections dry and off the
ground. DO NOT touch plug with wet
hands.
We do not recommend that you use extension
cords with this pressure washer. If, however, your
application requires that you need an extension
cord, use only extension cords that are approved for
outside use. hese extension cords are identified by
a marking ACCEP ABLE FOR USE WI H OU -
DOOR APPLIANCES; S ORE INDOORS WHILE
NO IN USE. Use only extension cords having an
electrical rating not less than the rating of the prod-
uct. Do not use damaged extension cords.
urn on the water.
NOTE: Inlet water temperature should not exceed
104°F.
DANGER: You must attach the spray gun
and all hoses before you start the motor.
DANGER: You must be careful at this point.
Anytime you squeeze the trigger, the motor
will start and water will spray out of the
gun.
Squeeze trigger to purge pump of system air and
impurities.
Attach nozzle extension to spray gun by aligning the
locking tabs on the extension with the grooves in
the gun. Push extension inward and twist clockwise
to lock in place (Figure 5).
Press the master On/Off Switch to the On position
(Figure 6).
CAUTION: Before starting the pressure
washer, be sure you are wearing adequate
eye protection. Goggles are included with
this unit.
WARNING: Gun kicks back. Use both
hands.
DANGER: Risk of injury or injection to
people and animals. DO NOT discharge
stream at people or animals.
AASSSSEEMMBBLLYY
Figure 4 — Connect Garden Hose to Water
Inlet Opening
Figure 6 — Press the Master On/Off Switch to
the “On” Position
Figure 5 — Connect the nozzle extension to
spray gun
8
High Pressure Washer
GENERAC
Generac 1300PSI Electric High Pressure Washer
Squeeze trigger to produce spray.
NOTE: Behind the trigger to the gun is a SAFE Y
LA CH. You can place this latch as shown in Figure 7
to keep the washer from accidentally spraying while
you are changing the nozzle head or foamer or per-
forming other tasks.
STOPPING YOUR PRESSURE
WASHER
If the pressure washer is running, release the trig-
ger.
DANGER: Releasing the trigger will shut
off the motor but does not shut off the
unit. You must also place the Master
On/Off Switch to the OFF position.
Place Master On/Off switch in Off position.
Simply shutting OFF motor will not release pres-
sure in the system. Squeeze the trigger on the gun
to relieve the pressure in the hose.
DANGER: Never leave your pressure
washer unattended even when turned off.
HOW TO USE YOUR WASHER
You now should know how to S AR your pressure
washer and how to S OP it. he information in this
section will tell you how to adjust the spray pattern
and apply detergent or any other cleaning chemicals.
HOW TO USE ADJUSTABLE NOZZLE
DANGER: Never adjust spray pattern when
spraying. Never put hands in front of spray
nozzle to adjust spray pattern. You could
be injured.
On the end of your spray gun is a nozzle that you can
twist from side to side. With the adjustable nozzle you
can adjust the spray configuration to be either concen-
trated in a stream or expanded into a fan pattern.
wist nozzle counterclockwise when you wish to
produce an expanded stream. wist nozzle clock-
wise to produce a narrow, concentrated stream
(Figure 8).
Figure 7 — Apply the Safety Latch.
Figure 8 — Using the Adjustable Nozzle.
Twist Nozzle
Counterclockwise
for Fan Spray
Twist Nozzle
Clockwise for
Narrow Spray.
9
High Pressure Washer
GENERAC
Generac 1300PSI Electric High Pressure Washer
Point the nozzle toward the ground and press the
trigger to test the pattern.
For most effective cleaning, keep spray nozzle
between 8 to 24 inches of cleaning surface.
If you get the spray nozzle too close, especially
using high pressure mode, you may damage the
cleaning surface.
Do not get closer than 6 inches when cleaning auto-
mobile tires.
Applying Detergent With Foamer
IMPORTANT: Use soaps designed specifically for
pressure washers. Household detergents could
damage the pump.
NOTE: Never use garden hose inlet to siphon deter-
gent or wax.
DANGER: You MUST attach all hoses and the spray
gun before you start the motor.
WARNING: Before removing any spray gun
extension, be sure to turn off the pressure
washer and relieve pressure by pressing
the trigger. You could be injured if you try
to remove an extension if the pressure
washer is running and there is pressure in
the system.
Pressure washers are useful cleaning tools designed
to clean almost any surface in two easy steps.
he first step involves applying an appropriate
detergent/solvent solution to penetrate and loosen
grime. he detergent is applied at low pressure to
avoid splashing, overspraying and waste. Leave the
solution on surface for 3 to 5 minutes to allow solu-
tion to work.
he second step involves cleaning the surface you
have prepared with the pressure washer and then
rinsing it clean.
To apply detergent follow these steps:
Detach the nozzle extension by pushing in and
unlocking it counterclockwise.
Remove the bottle from the foamer.
Align the locking tabs on the foamer with the groves
in the gun. Push inward and twist clockwise to lock
in place. (Note: make sure that the when you lock
the foamer into place you have the hose that con-
nects to the foamer bottle hanging downward.)
Prepare your detergent solution as required by your
job and fill bottle with the solution.
Attach bottle back onto foamer making sure the
bottle hangs down.
Start washer and apply detergent to a dry surface,
starting from the bottom and working up.
o rinse, YOU MUST, stop the pressure washer,
remove the foamer and connect the adjustable
nozzle extension.
NOTE: Detergents are most effective applied to a dry
surface.
To Clean
Start at lower portion of area to be washed and work
upward, using long, even overlapping strokes. Deter-
gent or degreaser works best when you apply it to a
dry surface first. Let it set for 3-5 minutes before
washing and rinsing.
Figure 10 Connecting the Foamer
10
High Pressure Washer
GENERAC
Generac 1300PSI Electric High Pressure Washer
GENERAC
Rinse
Start at the top of area to be rinsed, working down
with the same action as for cleaning.
How to Use the Rotating and Utility
Brushes
he rotating and utility brushes allow you to scrub
surfaces with water filtering through the bristles.
To attach a brush to the gun:
Attach the bayonet adapter to the base of the
brush. ighten.
Remove the adjustable nozzle lance from the gun if
attached.
Attach the brush with the bayonet adapter to the
spray gun by aligning the locking tabs on the
adapter with the grooves in the gun. Push the brush
inward and twist clockwise to lock in place.
Note: You must use the bayonet adapter to attach the
brush to the gun.
How to Use the Turbo Nozzle
he turbo nozzle, in essence, expands the area of the
high pressure stream. Use this nozzle when a large
area needs to be cleaned with the high pressure
stream.
To attach the turbo nozzle:
Remove the adjustable nozzle from the lance.
Attach the turbo nozzle to the lance.
CUSTOMER RESPONSIBILITIES
AND MAINTENANCE
he warranty of the high pressure washer does not
cover items that have been subjected to operator
abuse or negligence. o receive full value from the
warranty, operator must maintain high pressure
washer as instructed in this manual.
BEFORE EACH USE
Check and Clean Quick-Connect
Screen
Remove quick-connect and examine the inlet screen
on the female connector. Clean if clogged or replace
the quick-connect inlet screen if damaged.
Check High Pressure Hose
DANGER: Water spraying from a leak is
capable of injecting material into skin.
Inspect hose each time before using it.
Never repair high pressure hose. Replace it
with another hose that meets minimum
pressure rating of your pressure washer.
High pressure hose can develop leaks from wear,
kinking, and abuse. Check all hoses for cuts, leaks,
abrasions or bulging of cover, or damage or move-
ment of couplings. If any of these conditions exist,
replace hose immediately.
Check Gun and Wand
Examine hose connection and make sure it is secure.
est trigger by pressing it and making sure it springs
back into place when released. Put safety latch in ON
position and test trigger. You should not be able to
press trigger.
PURGE PUMP OF AIR AND
CONTAMINANTS
To remove the air from the pump, follow these
steps:
Set up the pressure washer as described in the
ASSEMBLY section and connect the water supply.
Remove the nozzle lance from the gun.
Pull the trigger on the gun and hold.
To remove the contaminant from the pump, follow
these steps:
Set up the pressure washer as described in the
ASSEMBLY section, connect the water supply and
start the pressure washer according to instructions
in the OPERA ION section.
Remove the nozzle lance from the gun.
Pull the trigger on the gun and hold.
When the water supply is steady and constant, you
may refasten the nozzle attachment and start the
pump.
Otros manuales para 1300PSI
1
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Hidrolavadora de Generac Power Systems
Generac Power Systems
Generac Power Systems DPW3101DEN Manual de usuario
Generac Power Systems
Generac Power Systems 2500PSI Manual de usuario
Generac Power Systems
Generac Power Systems 1420-0 Manual de usuario
Generac Power Systems
Generac Power Systems 3000CP Manual de usuario
Generac Power Systems
Generac Power Systems The Reliable Ones Manual de usuario
Generac Power Systems
Generac Power Systems Power Washer Manual de usuario
Generac Power Systems
Generac Power Systems 2700PSI 1676-0 Manual de usuario
Generac Power Systems
Generac Power Systems 1043-2 Manual de usuario
Generac Power Systems
Generac Power Systems 1300PSI Manual de usuario
Generac Power Systems
Generac Power Systems 2600 PSI Manual de usuario
Generac Power Systems
Generac Power Systems 1455-0 Manual de usuario
Generac Power Systems
Generac Power Systems 1044-1 Manual de usuario
Generac Power Systems
Generac Power Systems 2000PSI Manual de usuario
Generac Power Systems
Generac Power Systems 1455-0 Manual de usuario
Generac Power Systems
Generac Power Systems 2000PSI Manual de usuario
Generac Power Systems
Generac Power Systems 2100PSI 1536-0 Manual de usuario
Generac Power Systems
Generac Power Systems 1750PSI Manual de usuario
Generac Power Systems
Generac Power Systems BELT DRIVEN POWER WASHER Manual de usuario
Generac Power Systems
Generac Power Systems 1293-1 Manual de usuario
Generac Power Systems
Generac Power Systems Power Washer Manual de usuario
