Generac Power Systems 2000PSI Manual de usuario

This pressure

washer is

equipped with an

Automatic Cool

Down System.

See page 12 for

details

This symbol points out important safety instructions, which, if not followed, could endan

ger the personal safety and/or property of yourself and others. Read and follow all

instructions in the manual before attempting to operate this unit.

Model No. 10402 (2000 PSI High Pressure Washer) Manual No. B3408 Revision 0 (12/28/98)

2000PSI

Owner’s Manual

Problems?

Questions?

Before taking your unit

back to the store,

call the pressure washer

helpline at

1 800 270 1408

M F 8 5 CST

GENERAC

The Reliable Ones

Generac 2000PSI High Pressure Washer

GENERAC

The Reliable Ones

SAFETY RULES

DANGER! Always disconnect spark plug

wire and place wire where it cannot

contact spark plug to prevent accidental

starting when setting up, transporting,

adjusting or aking repairs to your high

pressure washer.

 Engine exhaust gases contain DEADLY carbon

onoxide gas. This dangerous gas, if breathed

in sufficient concentrations, can cause

unconsciousness or even death. Operate this

equip ent only in the open air where adequate

ventilation is available.

 Gasoline is highly FLAMMABLE and its vapors

are EXPLOSIVE. Do not per it s oking, open

fla es, sparks or heat in the vicinity while

handling gasoline. Avoid spilling gasoline on a

hot engine. Allow unit to cool for 2 inutes

before refueling. Co ply with all laws

regulating storage and handling of gasoline.

 Locate this pressure washer in areas away

fro co bustible aterials, co bustible fu es

or dust.

 The high pressure equip ent is designed to be

used with Generac authorized parts only. If you

use this equip ent with parts that do not

co ply with ini u specifications, the user

assu es all risks and liabilities.

 So e che icals or detergents ay be har ful

if inhaled or ingested, causing severe nausea,

fainting or poisoning. The har ful ele ents

ay cause property da age or severe injury.

 Do not allow CHILDREN to operate the

Pressure Washer at any ti e.

 Operate engine only at governed speed.

Running the engine at excessive speeds

increases the hazard of personal injury. Do not

ta per with parts which ay increase or

decrease the governed speed.

 Do not wear loose clothing, jewelry or anything

that ay be caught in the starter or other

rotating parts.

 Before starting the Pressure Washer in cold

weather, check all parts of the equip ent and

be sure ice has not for ed there.

 Units with broken or issing parts, or without

protective housing or covers should NEVER be

operated.

 The uffler and air cleaner ust be installed

and in good condition before operating the

Pressure Washer. These co ponents act as

spark arrestors if the engine backfires.

 Check the fuel syste for leaks or signs of

deterioration such as chafed or spongy hose,

loose or issing cla ps or da aged tank or

cap. Correct all defects before operating the

Pressure Washer.

 Do not spray fla able liquids.

 Never ai the gun at people, ani als or

plants.

 High pressure spray can cause paint chips or

other particles to beco e airborne and fly at

high speeds.

The engine exhaust from this product

contains chemicals known to the State

of California to cause cancer, birth

defects, or other reproductive harm.

WARNING:

IMPORTANT!  SAFETY RULES  IMPORTANT!

Generac 2000PSI High Pressure Washer

GENERAC

The Reliable Ones

 Never allow any part of the body to co e in

contact with the fluid strea . DO NOT co e in

contact with a fluid strea created by a leak in

the high pressure hose.

 The high pressure strea of water that this

equip ent produces can pierce skin and its

underlying tissues, leading to serious injury

and possible a putation.

 Always wear eye protection when you use this

equip ent or when you are in the vicinity

where the equip ent is in use.

 Never ove the achine by pulling on the high

pressure hose. Use the handle provided on the

top of the unit.

 Always be certain the spray gun, nozzles and

accessories are correctly attached.

 Never use a spray gun which does not have a

trigger lock or trigger guard in place and in

working order.

 Use a respirator or ask whenever there is a

chance that vapors ay be inhaled. Read all

instructions with ask so you are certain the

ask will provide the necessary protection

against inhaling har ful vapors.

 High pressure spray ay da age fragile ite s

including glass. Do not point spray gun at glass

when in the jet spray ode.

 Keep the hose connected to achine or the

spray gun while the syste is pressurized.

Disconnecting the hose while the unit is

pressurized is dangerous.

 Hold the spray gun fir ly in your hand before

you start the unit. Failure to do so could result

in an injury fro a whipping spray gun. Do not

leave the spray gun unattended while the

achine is running.

 The cleaning area should have adequate

slopes and drainage to reduce the possibility of

a fall due to slippery surfaces.

 Keep water spray away fro electric wiring or

fatal electric shock ay result.

 Do not secure trigger gun in the pullback

(open) position.

 Do not bypass any safety device on this

achine.

 The uffler and engine heat up during

operation and re ain hot i ediately after

shutting it down. Avoid contact with a hot

uffler or engine or you could be severely

burned.

 Operate and store this unit on a stable surface.

 High pressure hose can develop leaks fro

wear, kinking, abuse, etc. Water spraying fro

a leak is capable of injecting aterial into

skin. Inspect hose each ti e before using it.

Check all hoses for cuts, leaks, abrasions or

bulging of cover, or da age or ove ent of

couplings. If any of these conditions exist,

replace hose i ediately. Never repair high

pressure hose. Replace it with another hose

that eets ini u pressure rating of your

pressure washer.

IMPORTANT!  SAFETY RULES  IMPORTANT!

Generac 2000PSI High Pressure Washer

GENERAC

The Reliable Ones

ASSEMBLY

CONGRATULATIONS on your purchase of a

GENERAC high pressure washer. It has been

designed, engineered and anufactured to give you

the best possible dependability and perfor ance.

Should you experience any proble you cannot

easily re edy, please contact your nearest

GENERAC Authorized Service facility, or call the

1800 nu ber listed on the front of this anual. We

have co petent, welltrained technicians and the

proper tools to service or repair this unit.

Please read and retain this anual. The instructions

will enable you to asse ble and aintain your high

pressure washer properly.

CUSTOMER

RESPONSIBILITIES

 Read and observe the safety rules.

 Follow regular schedule in aintaining, caring for

and using your high pressure washer.

 Follow the instructions under Custo er

Responsibilities and Storage sections of this

Owner's Manual.

PRODUCT

SPECIFICATIONS

Pressure Washer Specifications

Outlet Pressure . . . . 2000 psi

Flow Rate . . . . . . . . . 2.0 gallons per inute (gp )

Detergent Mix . . . . . . Use undiluted detergent

approved for pressure

washers

Water Supply . . . . . . Not to Exceed 140°F

Temperature

Automatic Cool . . . . Will cycle when water

Down System reaches 140°-145°F

Engine Specifications

Engine Model . . . . . . Briggs & Stratton Quantu

Rated Horsepower . . 6.0

Displacement . . . . . . 190cc

Spark Plug

Type . . . . . . . . RJ19LM

Set Gap To: . . 0.030 inch (0.76 )

Gasoline Capacity . . 1.6 U.S. quarts

Oil . . . . . . . . . . . . . . . SAE 30

In the State of California a spark arrestor is required

by law (Section 4442 of the California Public

Resources Code). Other states ay have si ilar

laws. Federal laws apply on federal lands.

NOTE: If you equip the engine of your pressure

washer with a spark arrestor uffler, the spark

arrestor ust be aintained in effective working order

by the owner/operator.

You can order a spark arrestor through your

authorized Briggs & Stratton service facility. See

Engine Owners Manual for part nu ber.

Model Number 10402

Serial Number

Date of Purchase

The odel and serial nu bers will be found on a

decal attached to the pressure washer. Record

both serial nu ber and date of purchase and

keep in a safe place for future reference.

Generac 2000PSI High Pressure Washer

GENERAC

The Reliable Ones

ASSEMBLY

KNOW YOUR PRESSURE WASHER

Read this owners manual and safety rules before operating your high pressure washer.

Co pare the illustrations with your high pressure washer to fa iliarize yourself with the locations of various

controls and adjust ents. Save this anual for future reference.

Adjustable Nozzle Extension  You ust attach this

to the spray gun to provide high pressure strea . The

adjustable nozzle allows you to adjust the spray pattern

which, in turn, adjusts the force of spray.

Air Cleaner  Dry type filter ele ent li its the a ount

of dirt and dust that gets in the engine.

Automatic Cool Down System  Cycles water

through pu p when water reaches 140°-145°F. Warm

water will discharge from pump onto ground. This

system prevents internal pump damage.

Gas Tank  Fill with regular unleaded gasoline only.

Goggles  Always use the enclosed goggles or other

eye protection when running your pressure washer.

High Pressure Hose  Connect one end to water

pu p and the other end to spray wand.

High Pressure Outlet  Connection for high pressure

hose.

Oil Fill Tube  Fill engine with oil here. See page 7 for

oil reco endations.

Pump  Develops high pressure.

Recoil Starter  Used for starting the engine

anually.

Spray Gun  Controls the application of water onto

cleaning surface with trigger device. Includes safety

latch.

Water Inlet  Connection for garden hose.

Spray Gun

Adjustable Nozzle

Extension

High Pressure Hose

Goggles

Air Cleaner

Gas Tank

Water Inlet

Pump equipped with

Automatic Cool Down System

Recoil Starter

High Pressure Outlet

Oil Fill Tube

Generac 2000PSI High Pressure Washer

GENERAC

The Reliable Ones

ASSEMBLY

Read entire owners anual before you atte pt to

asse ble or operate your new pressure washer.

Your new pressure washer has been asse bled at

the factory with the exception of those parts left

unasse bled for shipping purposes.

REMOVE PRESSURE

WASHER FROM CARTON

 Re ove parts box included with pressure washer.

 Slice two corners at guide handle end of carton

fro top to botto so the panel can be folded down

flat, then re ove all packing aterial.

 Roll pressure washer out of carton.

CARTON CONTENTS

Ite s in the carton include:

 Main Unit

 Parts Box (which includes the following):

 Wirefor

 ORing Maintenance Kit.

 Video

 Goggles

 Nozzle Cleaning Kit

 Owners Manual

 Engine Manual

 Spray Gun

 Nozzle Extension

 High Pressure Hose

 Handle

 Parts Bag (which includes the following):

 1 carriage bolt

 1 carriage hook

 2 knobs

If any of the above parts are issing or da aged, call

the pressure washer helpline at 18002701408.

PREPARING THE

PRESSURE WASHER

FOR USE

If you have any proble s with the asse bly of your

pressure washer or if parts are issing or da aged,

call the Pressure Washer Helpline at 1 800 270 1408.

To prepare your pressure washer for operation you

will need to perfor these tasks:

 Attach the handle and attach the wire for that

holds high pressure hose and spray gun.

 Connect high pressure hose to the spray gun and

the pu p and connect water supply to the pu p.

 Add oil to engine crankcase.

 Add fuel to fuel tank.

Attach the Handle

 Place the top of the handle onto the botto of the

handle already connected to the ain unit aking

sure the holes in the top align with the holes on the

botto (Figure 1).

Figure 1  Attach the top of the handle to

the botto of the handle.

Make sure the

holes on the

top of the

handle are

aligned with the

holes in the

bottom of the

handle

 Insert the carriage bolt through the right hole

(looking at the front of the pressure washer) and

attach a plastic knob. Tighten the knob by hand

(Figure 2).

 Insert the carriage hook through the left hole

(looking at the front of the pressure washer). Pull

the recoil handle out slowly. Place the recoil string

through the hook and attach the plastic knob.

Tighten the knob by hand (Figure 2).



Insert the wire for with the longer ar positioned on

the left. Fro this view (fro rear of unit) the hook

should rese ble a J

(Figure 3)

Add Engine Oil

IMPORTANT: Any atte pt to crank or start the

engine before it has been properly serviced with the

reco ended oil ay result in an engine failure.

Note: When adding oil to the engine crankcase, use

only high quality detergent oil rated with API service

classification SF,SG, SH or SH/CD rated SAE 30

weight. Select the oils viscosity grade according to

your expected operating te perature:

Do Not Use SAE 10W40 Oil.

Although ultiviscosity oils (5W30, 10W30, etc.)

i prove starting in cold weather, these ultiviscosity

oils will result in increased oil consu ption when used

above 32°F. Check your engine oil level ore

frequently to avoid possible da age fro running

low on oil.

 Place pressure washer on a level surface.

 Clean area around oil fill and re ove oil dipstick

(Figure 4).

 Wipe dipstick clean. Pour oil into oil fill opening until

oil reaches FULL ark on the dipstick. Stop

occasionally to check oil level. DO NOT OVERFILL.

 Install oil dipstick, hand tighten securely.

Note: Check Oil Often During Engine Breakin.

Add Gasoline

DANGER! Never fill fuel tank indoors. Never

fill fuel tank when engine is running or hot. Do

not s oke when filling fuel tank.

WARNING! Never fill fuel tank co pletely full.

Fill tank to about 1/2" below the botto of the

filler neck to provide space for fuel expansion.

Wipe away any fuel spillage fro engine and

equip ent before starting.

Generac 2000PSI High Pressure Washer

GENERAC

The Reliable Ones

ASSEMBLY

Figure 3  Fit wire for on handle.

Figure 4  Add oil to engine crankcase. Do not

atte pt to start engine without adding

oil.

Oil Fill Cap

Figure 2  Insert the carriage bolt and hook and

attach the knobs.

colder 32°F war er

5W30 SAE 30

Generac 2000PSI High Pressure Washer

GENERAC

The Reliable Ones

ASSEMBLY

The anufacturer reco ends fresh, clean unleaded

auto otive gasoline.

 Use clean fuel and store in approved, clean,

covered containers. Use clean fill funnels. Never

use stale gasoline left over fro last season or

gasoline stored for long periods.

 Clean area around fuel fill cap, re ove cap.

(Figure 5).

 Add UNLEADED regular gasoline, slowly, to fuel

tank. Use a funnel to prevent spillage.

 Install fuel cap and wipe up any spilled gasoline.

Connect Hose and Water

Supply to Pump

IMPORTANT: You ust asse ble wand and attach

all hoses before you start engine. Starting engine

without all hoses connected and water supplied will

da age pu p.

 Uncoil high pressure hose and attach one end of

hose to the base of the spray gun (Figure 6).

Tighten by hand.

 Attach other end of high pressure hose to the high

pressure outlet on the pu p (Figure 7). Tighten by

hand.

 Before you connect your garden hose to the water

inlet, inspect the Inlet Screen (Figure 8). Clean the

screen if it contains debris or have it replaced if

da aged. Do not run the pressure washer if the

inlet screen is damaged.

 Connect garden hose to water inlet. Tighten by

hand (Figure 8).

 Turn ON the water (open valve co pletely).

 Squeeze trigger on gun to purge pu p syste of

air and i purities.

CAUTION! Before starting the pressure

washer, be sure you are wearing adequate

eye protection.

Figure 7  Connect high pressure hose to pu p.

Figure 6  Connect high pressure hose

to spray gun.

Figure 8  Connect the garden hose to water inlet

and turn ON the water.

Figure 5  Add gasoline to fuel tank.

Fuel Cap

Connect High Pressure

Hose Here

Check Screen for Damage

Generac 2000PSI High Pressure Washer

GENERAC

The Reliable Ones

ASSEMBLY

 Attach nozzle extension to spray gun. Tighten by

hand (Figure 9). CHECKLIST BEFORE

STARTING ENGINE

If you have reached this point, look back over the

asse bly to see if you have perfor ed all of the

following.

 Check for properly tightened hose connections

(high pressure and water supply) and for tight

connections and that there are no kinks, cuts, or

da age to the high pressure hose.

 Check that oil has been added to proper level in

engine crankcase before trying to start the pressure

washer.

 Add proper gasoline to fuel tank.

 Provide proper water supply (not to exceed 140°F).

 Be sure to read Safety Rules and Operation

sections before using the pressure washer.

Figure 9  Connect nozzle extension to spray gun.

Generac 2000PSI High Pressure Washer

GENERAC

The Reliable Ones

HOW TO USE YOUR

PRESSURE WASHER

If you have any proble s operating your pressure

washer, please call the pressure washer helpline at

18002701408.

You have asse bled your high pressure washer and

have prepared the engine for starting. You are now

ready to clean your car, boat or the outside of a

building or whatever you plan to clean.

How to Start Your Engine

The best way to start your enginepowered pressure

washer for the first ti e is to follow these instructions

stepbystep. This starting infor ation also applies

whenever you start the engine after you have let the

pressure washer sit idle for at least a day.

 This pressure washer requires a water source that

flows at least 2 gallons per inute. Do not attempt

to siphon water from a nonpressurized

container. Place the pressure washer close

enough to an outside water source so that no ore

than 50' of garden hose is needed.

 Check that the high pressure hose is tightly

connected to the spray gun and to the pu p. See

ASSEMBLY section for illustrations.

 Connect the garden hose to water inlet on the

pressure washer pu p and turn the water on all

the way.

IMPORTANT: Do not run pu p without the water

supply connected and turned on. You ust follow this

caution or the pu p will be da aged.

 Move the Throttle Control Lever to the Fast

position

 Set Choke Lever to Choke position.

Note: This is a ultiposition choke.

Note: For a war engine, be sure the Throttle

Control Lever is in the Fast position and the Choke

Lever is in the Run position.

 Squeeze the trigger on the spray gun to relieve air

pressure caused by turning ON the water. Water

will spew out the gun in a thin strea . Continue to

hold trigger until you have a steady strea of water

and no air re ains.This will ake it easier to pull

start the engine. Release the trigger.

 Apply the safety latch to the spray gun trigger

(Figure 10).

 Grasp rope handle and pull slowly until you feel

so e resistance. Then pull cord rapidly to

overco e co pression, prevent kickback and start

the engine. Let rope return to starter slowly.

Note: Always keep the Throttle Control Lever in the

Fast position when operating the pressure washer.

 When the engine starts, gradually ove the Choke

Lever fro one position to the next until it is in the

Run position.

If after 3 pulls the engine fails to start, disengage the

spray gun safety latch, squeeze the trigger to relive

water pressure, reengage the spray gun safety latch,

ove the Choke Lever to the Run position and pull

the recoil starter handle rapidly (Max. 3 pulls).

How to Stop Your Pressure

Washer

 Move the Throttle Control Lever to the Slow position.

 Wait for the engine to idle down.

 Move the Throttle Lever Lever to the Stop position.

 Si ply shutting off the engine will not release

pressure in the syste . Squeeze trigger on the

spray gun to relieve pressure in the hose.

Note: A s all a ount of water will squirt out when

you release the pressure.

Figure 10  Squeeze trigger to relieve water

pressure, release trigger and turn

the safety latch ON.

Safety Latch ON

Otros manuales para 2000PSI

Este manual sirve para los siguientes modelos

Otros manuales de Hidrolavadora de Generac Power Systems

Generac Power Systems

Generac Power Systems 1540-0 Manual de usuario

Generac Power Systems

Generac Power Systems The Reliable Ones Manual de usuario

Generac Power Systems

Generac Power Systems OneWASH 6412 Manual de usuario

Generac Power Systems

Generac Power Systems DPW3101DEN Manual de usuario

Generac Power Systems

Generac Power Systems 4040 PRO GAS PW 49ST Manual de usuario

Generac Power Systems

Generac Power Systems 2100PSI 1974-0 Manual de usuario

Generac Power Systems

Generac Power Systems 1014-0 Manual de usuario

Generac Power Systems

Generac Power Systems 6020-2 Manual de usuario

Generac Power Systems

Generac Power Systems 1418-1 Manual de usuario

Generac Power Systems

Generac Power Systems 7132 Manual de usuario

Generac Power Systems

Generac Power Systems 1037-0 Manual de usuario

Generac Power Systems

Generac Power Systems 1173-1 Manual de usuario

Generac Power Systems

Generac Power Systems 3000PSI Manual de usuario

Generac Power Systems

Generac Power Systems Power Washer Manual de usuario

Generac Power Systems

Generac Power Systems 3000CP Manual de usuario

Generac Power Systems

Generac Power Systems 006022-0 Manual de usuario

Generac Power Systems

Generac Power Systems 2000PSI Manual de usuario

Generac Power Systems

Generac Power Systems 2700PSI 1676-0 Manual de usuario

Generac Power Systems

Generac Power Systems BELT DRIVEN POWER WASHER Manual de usuario

Generac Power Systems

Generac Power Systems 1293-1 Manual de usuario

Generac Power Systems

Generac Power Systems Power Washer Manual de usuario

Generac Power Systems

Generac Power Systems 1700PSI Manual de usuario

Generac Power Systems

Generac Power Systems 1044-1 Manual de usuario

Generac Power Systems

Generac Power Systems Power Washer Manual de usuario

Manuales populares de Hidrolavadora de otras marcas

Shark

Shark RG-232637 Manual de usuario

Shakti Technology

Shakti Technology S3 Manual de usuario

Kärcher

Kärcher K 4 Pure Manual de usuario

Porter-Cable

Porter-Cable D25806-025-2 Manual de usuario

REM POWER

REM POWER HDEm 662 Manual de usuario

Landa

Landa HS-3000 Manual de usuario

Craftsman

Craftsman 580.752270 Manual de usuario

HIKOKI

HIKOKI AW 100 Manual de usuario

Delco

Delco DC 1302 Manual de usuario

Kärcher

Kärcher K 3 Full Control Manual de usuario

BIEMMEDUE

BIEMMEDUE 120/10 - 170/13 Manual de usuario

ARKSEN

ARKSEN 014-HG-14141-HR Manual de usuario

Black & Decker

Black & Decker PW1700SPX Manual de usuario

Kärcher

Kärcher 595 - SPARE Guía

Kranzle

Kranzle B 10 200 Manual de usuario

Stihl

Stihl RE 90 Manual de usuario

Husky

Husky HU80911 Manual de usuario

PowR-Quip

PowR-Quip PQ-2600 Manual de usuario