Generac Power Systems 1300PSI Manual de usuario

1300PSI

Owner’s Manual Problems?

Questions?

Before taking your unit

back to the store,

call the pressure washer

helpline at

1-800-2 0-1408

M-F 8-5 CST

GENERAC

The Reliable Ones

This symbol points out important safety instructions, which, if not followed, could

endanger the personal safety and/or property of yourself and others. Read and follow all

instructions in the manual before attempting to operate this unit.

Model No. 12800 (1300 PSI High Pressure Washer) Manual No. B3 19 Revision 0 (1/2 /99)

Generac 1300PSI High Pressure Washer

GENERAC

The Reliable Ones

CAUTION! Read all instructions before using

this product to reduce the risk of injur .

DANGER! Risk of electrocution!

 Inspect cord before ever use. Do not use if cord is

damaged.

 Keep all connections dr and off the ground.

 Do not touch plug with wet hands.

 Doubleinsulated  When servicing, use onl

identical replacement parts.

 This product shall onl be connected to a power

suppl receptacle protected b a Ground Fault

Circuit Interrupter (GFCI).

 Read instruction manual before using.

WARNING! To reduce the risk of injur , close

supervision is necessar when product is used

near children.

 Know how to stop the product and bleed the

pressure quickl . Be thoroughl familiar with

controls.

 Sta alert. Watch what ou are doing.

 Do not operate the product when fatigued or under

the influence of alcohol or drugs.

 Keep operating area clear of all persons.

WARNING! Risk of injur or injection to

persons  Do not discharge stream at persons

or animals.

 High pressure hose can develop leaks from wear,

kinking, abuse, etc. Water spra ing from a leak is

capable of injecting material into skin. Do not point

the pressure washer spra at people or animals.

 Do not overreach or stand on unstable support.

Keep good footing and balance at all times.

 Follow the maintenance instructions specified in the

manual.

 This product shall onl be connected to a power

suppl receptacle protected b a Ground Fault

Circuit Interrupter (GFCI). This is done to compl

with National Electrical Code (NFPA 70) and to

provide additional protection from risk of electrical

shock.

 Save these instructions.

 Operate this pressure washer onl in areas awa

from combustible materials, combustible fumes or

dust.

 Some chemicals or detergents ma be harmful if

inhaled or ingested, causing severe nausea,

fainting or poisoning. The harmful elements ma

cause propert damage or severe injur .

 Do not allow CHILDREN to operate the Pressure

Washer at an time.

 Before starting the Pressure Washer in cold

weather, check all parts of the equipment and be

sure ice has not formed.

 Units with broken or missing parts, or without

protective housing or covers should NEVER be

operated.

DANGER! Risk of Explosion  Do not spra

flammable liquids.

 Never aim the gun at people, animals or plants.

 For household use. For indoor or outdoor use.

 High pressure stream of fluid that this equipment

can produce ma pierce skin and its underl ing

tissues, leading to serious injur and possible

amputation.

 High pressure spra can cause paint chips or other

particles to become airborne and fl at high speeds.

Save these instructions

Important!  Safety Instructions  Important!

Generac 1300PSI High Pressure Washer

GENERAC

The Reliable Ones

 Alwa s wear e e protection when ou use this

equipment or when ou are in vicinit where the

equipment is in use.

 Never move the machine b pulling on high

pressure hose. Use the handle provided on the top

of the unit.

 Use a respirator or mask whenever there is a

chance that vapors ma be inhaled. Read all

instructions with the mask so ou are certain the

mask will provide the necessar protection against

inhaling harmful vapors.

 High pressure spra ma damage fragile items

including glass. Do not point spra gun at glass

when in the high pressure mode.

 Keep the hose connected to machine or the spra

gun while the s stem is pressurized. Disconnecting

the hose while the unit is pressurized is dangerous.

 Hold the spra gun firml in our hand before ou

start the unit. Do not leave the pressure washer

unattended while the machine is turned on.

 Cleaning area should have adequate slopes and

drainage to reduce possibilit of a fall due to

slipper surfaces.

 Keep water spra awa from electric wiring or fatal

electric shock ma result.

 Do not b pass an safet device on this machine.

 Operate and store this unit on a stable surface.

 Inspect hose each time before using it. Check all

hoses for cuts, leaks, abrasions, bulging of cover,

damage or movement of couplings. If an of these

conditions exist, replace hose immediatel . Never

repair high pressure hose. Replace it with another

hose that meets minimum pressure rating of our

pressure washer.

 Store in a clean, dr area. Ideall , the unit should be

stored in a frostfree room.

Servicing of a Double Insulated Product.

In a doubleinsulated product, two s stems of

insulation are provided instead of grounding. No

means of grounding is provided on a

doubleinsulated product, nor should a means for

grounding be added.

Servicing a doubleinsulated product requires

extreme care and knowledge of the s stem and

should be done onl b qualified service personnel.

Replacement parts for a doubleinsulated product

must be identical to the parts the replace. Use onl

genuine replacement parts. A doubleinsulated

product is marked with the words DOUBLE

INSULATION or DOUBLE INSULATED.

The s mbol ma also be marked on the product.

Extension Cords

Use onl extension cords that are approved for

outside use. These extension cords are identified b

a marking ACCEPTABLE FOR USE WITH

OUTDOOR APPLIANCES; STORE INDOORS

WHILE NOT IN USE. Use onl extension cords

having an electrical rating greater than the rating of

the product. Do not use damaged extension cords.

Examine extension cord before using and replace if

damaged. Do not abuse extension cord and do not

ank on an cord to disconnect it. Keep cord awa

from heat and sharp edges. Alwa s disconnect the

extension cord from the receptacle before

disconnecting the pressure washer from the

extension cord.

Save these instructions

Important!  Safety Instructions  Important!

Generac 1300PSI High Pressure Washer

GENERAC

The Reliable Ones

CONGRATULATIONS on our purchase of a

GENERAC electric high pressure washer. It has been

designed, engineered and manufactured to give ou

the best possible dependabilit and performance.

Should ou experience an problem ou cannot easil

remed , please contact our nearest GENERAC

Authorized Service facilit , or call 18002 01408.

We have competent, welltrained technicians and the

proper tools to service or repair this unit.

Please read and retain this manual. The instructions

will enable ou to assemble and maintain our high

pressure washer properl . Alwa s observe the

SAFETY INSTRUCTIONS.

CUSTOMER

RESPONSIBILITIES

 Read and observe the safet rules.

 Follow regular schedule in maintaining, caring for

and using our high pressure washer.

 Follow the instructions under Maintenance and

Storage sections of this Owner's Manual.

PRODUCT

SPECIFICATIONS

Pressure Washer Specifications

Pressure 1300 pounds per square inch

(PSI)

Flow Rate 1.5 gallons per minute (GPM)

Detergent Mix Use Undiluted Detergent

Water Supply Inlet water not to exceed

Temperature 104°F

Motor Brush T pe (Universal)

Rated Voltage 120 Volts

Current 14 Amperes

Read these instructions and Operators Manual in its

entiret before ou attempt to assemble or operate

our new high pressure washer. Your high pressure

washer has, for the most part, been assembled at the

factor . Before ou can operate our new high

pressure washer, ou must properl connect the high

pressure hose and the water suppl .

If ou have an problems with the assembl of our

pressure washer, please call the pressure washer

helpline at 18002 01408.

Model

Number 12800

Serial

Number_________________________________

Date of

Purchase________________________________

The model and serial numbers will be found on a

decal attached to the pressure washer. Record

both serial number and date of purchase and keep

in a safe place for future reference

KNOW YOUR PRESSURE WASHER

Read this owners manual and safety rules before operating your high pressure washer. Compare the

illustrations with our high pressure washer to familiarize ourself with the locations of various controls and

adjustments. Save this manual for future reference.

Generac 1300PSI High Pressure Washer

GENERAC

The Reliable Ones

Foamer  Used to appl detergent. Mixes water

and detergent in outlet water flow.

Garden Hose Connector (Not Shown)  Allows

rapid connection of our garden hose to the water

inlet.

Goggles  Alwa s wear e e protection when

operating our pressure washer.

Grip Start System  Pressing and releasing the

spra gun trigger starts and stops the electric motor in

the pressure washer.

High Pressure Hose  Connect ends to spra gun

and high pressure outlet.

High Pressure Outlet  Connection for high

pressure hose.

Master On/Off Switch  This switch ONLY enables

the Grip Start s stem to function.

Spray Gun  Controls the application of water onto

cleaning surface with trigger device. Includes safet

latch.

Turbo Nozzle and Extension  Attaches to the

spra gun and allows ou to clean or rinse surfaces at

high pressure. You cannot appl detergent using the

turbo nozzle.

Water Inlet  Connection for garden hose.

Spray Gun

Master On/Off Switch

High Pressure Outlet

High Pressure

Hose Turbo Nozzle and

Extension

Water Inlet

Grip Start

System

Foamer

Goggles

Generac 1300PSI High Pressure Washer

GENERAC

The Reliable Ones

CARTON CONTENTS

Items in the carton include:

 Main Unit

 Parts Box (which includes the following):

 Goggles

 Owners Manual

 Spra Gun

 Turbo Nozzle and Extension

 Foamer

 High Pressure Hose

 Garden Hose Connector

Refer to the above list for an illustrated listing of all

items included with our pressure washer. Become

familiar with each piece before assembling the

pressure washer. Check all contents against list. If

an parts are missing, call the pressure washer

helpline at 18002 01408.

HOW TO SET UP YOUR

PRESSURE WASHER

 Unwind the high pressure hose and attach it to

spra gun (Figure 1).

 Attach the high pressure hose to the high pressure

outlet and tighten b hand (Figure 2).

 Check the screen on the garden hose connector.

Make sure it is clean and check for damage. If ou

see an damage in the screen, do not use

(Figure 3).

 Attach the garden hose connector to the pressure

washer.

 Attach garden hose to the pressure washer.

DANGER! When connecting the unit to a

power suppl receptacle, use ONLY a

receptacle protected b a Ground Fault Circuit

Interrupter (GFCI). This will help protect

against electrical shock.

Figure 2  Attach High Pressure Hose to Main

Unit.

Figure 1  Attach High Pressure Hose to Spra

Gun.

Connect high pressure

hose here

Figure 3  Install Garden Hose Connector and

Attach Garden Hose.

Check inlet screen.

Connect garden hose

here.

Generac 1300PSI High Pressure Washer

GENERAC

The Reliable Ones

CAUTION! Before starting ou should be

sure the electrical suppl is rated at 120 volts,

15 amps.

WARNING! To reduce the risk of

electrocution, keep ALL connections dr and

off the ground. DO NOT touch plug with wet

hands.

Note: We do not recommend that ou use extension

cords with this pressure washer. If, however, our

application requires that ou need an extension cord,

use onl extension cords that are approved for

outside use. These extension cords are identified b a

marking ACCEPTABLE FOR USE WITH OUTDOOR

APPLIANCES; STORE INDOORS WHILE NOT IN

USE. Use onl extension cords having an electrical

rating not less than the rating of the product. Do not

use damaged extension cords.

DANGER! You must attach the spra gun

and all hoses before ou start the motor.

 Turn on the water.

NOTE: Inlet water temperature should not exceed

104°F.

DANGER! You must be careful at this point.

An time ou squeeze the trigger, the motor will

start and water will spra out of the gun.

 Squeeze trigger to purge pump of s stem air and

impurities.

 Attach the turbo nozzle extension to spra gun b

aligning the locking tabs on the extension with the

grooves in the gun. Push extension inward and twist

clockwise to lock in place (Figure 4).

 Press the master On/Off Switch to the On position

(Figure 5).

WARNING! Before starting the pressure

washer, be sure ou are wearing adequate e e

protection. Goggles are included with this unit.

WARNING! Gun kicks back. Use both

hands.

DANGER! Risk of injur or injection to

people and animals. DO NOT discharge

stream at people or animals.

 Squeeze trigger to produce spra .

NOTE: Behind the trigger to the gun is a SAFETY

LATCH. You can place this latch as shown (Figure 6)

to keep the washer from accidentall spra ing while

ou are changing the nozzle head or foamer or

performing other tasks.

Figure 5  Press the Master On/Off Switch to

the On Position.

Figure 4  Connect the Turbo Nozzle Extension

to the Spra Gun.

Figure 6  Appl the Safet Latch.

Generac 1300PSI High Pressure Washer

GENERAC

The Reliable Ones

STOPPING YOUR

PRESSURE WASHER

 If the pressure washer is running, release the

trigger.

DANGER! Releasing the trigger will shut off

the motor but does not shut off the unit. You

must also place the Master On/Off Switch to

the OFF position.

 Place Master On/Off switch in Off position.

Simpl shutting OFF motor will not release

pressure in the s stem. Squeeze the trigger on the

gun to relieve the pressure in the hose.

DANGER: Never leave our pressure

washer unattended even when turned off.

HOW TO USE YOUR

WASHER

You now should know how to START our pressure

washer and how to STOP it. The information in this

section will tell ou how to adjust the spra pattern

and appl detergent or an other cleaning chemicals.

How to Use the Turbo Nozzle

The turbo nozzle rotates the high pressure stream in

a rapid circular pattern. The high pressure spra is

most effective when the tip of the wand is held

between 8 to 24 inches from the surface being

cleaned.

Alwa s start the turbo nozzle at a distance, graduall

getting closer to the surface until ou get the cleaning

force ou want.

CAUTION! The turbo nozzle produces an

extremel high pressure spra which is

capable of removing paint and cutting holes

through surfaces if held too close. Alwa s

make sure the surface ou will clean will not

be damaged b the high pressure spra b

testing in a hidden area.

Note: You cannot appl detergent with the turbo

nozzle.

Applying Detergent With Foamer

IMPORTANT: Use soaps designed specificall for

pressure washers. Household detergents could

damage the pump.

NOTE: Never use garden hose inlet to siphon

detergent or wax.

DANGER: You MUST attach all hoses and the spra

gun before ou start the motor.

WARNING! Before removing an spra gun

extension, be sure to turn off the pressure

washer and relieve pressure b pressing the

trigger. You could be injured if ou tr to

remove an extension if the pressure washer is

running and there is pressure in the s stem.

Pressure washers are useful cleaning tools designed

to clean almost an surface in two eas steps.

 First, appl an appropriate detergent/solvent

solution to penetrate and loosen grime. Apply

detergent at low pressure to avoid splashing,

overspraying and waste. Leave the solution on

surface for 3 to 5 minutes to allow solution to work.

Reappl as necessar to keep solution from dr ing.

 The second step involves cleaning the surface ou

have prepared with the pressure washer and then

rinsing it clean.

Generac 1300PSI High Pressure Washer

GENERAC

The Reliable Ones

To apply detergent follow these steps:

 Detach the turbo nozzle extension from the spra

gun.

 Remove the bottle from the foamer.

 Align the locking tabs on the foamer with the groves

in the gun. Push inward and twist clockwise to lock

in place. (Note: make sure that when ou lock the

foamer into place ou have the hose that connects

to the foamer bottle hanging downward.)

 Prepare our detergent solution as required b the

manufacturer and fill bottle with the solution.

 Attach bottle back onto foamer making sure the

bottle hangs down.

 Start washer and appl detergent to a dr surface,

starting from the bottom and working up.

 To rinse, YOU MUST, stop the pressure washer,

remove the foamer and connect the adjustable

nozzle extension.

Note Detergents are most effective applied to a dr

surface.

To Clean

Start at lower portion of area to be washed and work

upward, using long, even overlapping strokes.

Detergent or degreaser works best when ou appl it

to a dr surface first. Let it set for 35 minutes before

washing and rinsing.

Rinse

Start at the top of area to be rinsed, working down

with the same action as for cleaning.

Figure 9  Connecting the Foamer.

Generac 1300PSI High Pressure Washer

GENERAC

The Reliable Ones

CUSTOMER

RESPONSIBILITIES AND

MAINTENANCE

The warrant of the high pressure washer does not

cover items that have been subjected to operator

abuse or negligence. To receive full value from the

warrant , operator must maintain high pressure

washer as instructed in this manual.

BEFORE EACH USE

Check and Clean Inlet Screen

Remove garden hose connector and examine the

inlet screen. Clean if clogged or replace the inlet

screen if damaged.

Check High Pressure Hose

DANGER: Water spra ing from a leak is

capable of injecting material into skin. Inspect

hose each time before using it. Never repair

high pressure hose. Replace it with another

hose that meets minimum pressure rating of

our pressure washer.

High pressure hose can develop leaks from wear,

kinking, and abuse. Check all hoses for cuts, leaks,

abrasions or bulging of cover, or damage or

movement of couplings. If an of these conditions

exist, replace hose immediatel .

Check Gun and Wand

Examine hose connection and make sure it is secure.

Test trigger b pressing it and making sure it springs

back into place when released. Put safet latch in ON

position and test trigger. You should not be able to

press trigger.

PURGE PUMP OF AIR AND

CONTAMINANTS

To remove the air from the pump, follow these

steps:

 Set up the pressure washer as described in the

ASSEMBLY section and connect the water suppl .

 Remove the turbo nozzle extension from the gun.

 Pull the trigger on the gun and hold.

To remove the contaminant from the pump, follow

these steps:

 Set up the pressure washer as described in the

ASSEMBLY section, connect the water suppl and

start the pressure washer according to instructions

in the OPERATION section.

 Remove the turbo nozzle extension from the gun.

 Pull the trigger on the gun and hold.

 When the water suppl is stead and constant, ou

ma refasten the turbo nozzle extension and use

pressure washer normall .

PREPARING THE UNIT FOR

STORAGE

Water should not remain in the unit for long periods of

time. Sediments of minerals can deposit on pump

parts and freeze pump action. If ou do not plan to

use the Pressure Washer for more than 30 da s,

follow this procedure:

1. Shut off the pressure washer, unplug it and let it

cool, then remove all hoses.

2. Store the pressure washer and its components in

such a wa as to protect it from freezing.

5. Store in a clean, dr area. Ideall , the unit should

be stored in a frostfree room.

6. Coil the high pressure hose and inspect it for

damage. Cuts in the hose or fra ing of it could result

in leaks and loss of pressure. Should an damage be

found, replace the hose. DO NOT attempt to repair a

damaged hose. Replace the hose with the genuine

Generac part.

7. Drain water from hose and properl store it to

prevent cuts and general wear.

Otros manuales para 1300PSI

Este manual sirve para los siguientes modelos

Otros manuales de Hidrolavadora de Generac Power Systems

Generac Power Systems

Generac Power Systems 1292-1 Manual de usuario

Generac Power Systems

Generac Power Systems 6000CP Manual de usuario

Generac Power Systems

Generac Power Systems 1300PSI Manual de usuario

Generac Power Systems

Generac Power Systems 1046-0 Manual de usuario

Generac Power Systems

Generac Power Systems 1460-0 Manual de usuario

Generac Power Systems

Generac Power Systems 3000CP Manual de usuario

Generac Power Systems

Generac Power Systems 1296-0 Manual de usuario

Generac Power Systems

Generac Power Systems 1455-0 Manual de usuario

Generac Power Systems

Generac Power Systems The Reliable Ones 1800PSI Manual de usuario

Generac Power Systems

Generac Power Systems 1044-1 Manual de usuario

Generac Power Systems

Generac Power Systems Power Washer Manual de usuario

Generac Power Systems

Generac Power Systems OneWASH Manual de usuario

Generac Power Systems

Generac Power Systems BELT DRIVEN POWER WASHER Manual de usuario

Generac Power Systems

Generac Power Systems Power Washer Manual de usuario

Generac Power Systems

Generac Power Systems 1067-0 Manual de usuario

Generac Power Systems

Generac Power Systems 1700PSI Manual de usuario

Generac Power Systems

Generac Power Systems The Reliable Ones Manual de usuario

Generac Power Systems

Generac Power Systems Pro 6712 Manual de usuario

Generac Power Systems

Generac Power Systems 1293-2 Manual de usuario

Generac Power Systems

Generac Power Systems Power Washer Manual de usuario

Generac Power Systems

Generac Power Systems 2000PSI Manual de usuario

Generac Power Systems

Generac Power Systems 1455-0 Manual de usuario

Generac Power Systems

Generac Power Systems 10000025895 Manual de usuario

Generac Power Systems

Generac Power Systems 1043-1 Manual de usuario

Manuales populares de Hidrolavadora de otras marcas

Shark

Shark RG-232637 Manual de usuario

Shakti Technology

Shakti Technology S3 Manual de usuario

Kärcher

Kärcher K 4 Pure Manual de usuario

Porter-Cable

Porter-Cable D25806-025-2 Manual de usuario

REM POWER

REM POWER HDEm 662 Manual de usuario

Landa

Landa HS-3000 Manual de usuario

Craftsman

Craftsman 580.752270 Manual de usuario

HIKOKI

HIKOKI AW 100 Manual de usuario

Delco

Delco DC 1302 Manual de usuario

Kärcher

Kärcher K 3 Full Control Manual de usuario

BIEMMEDUE

BIEMMEDUE 120/10 - 170/13 Manual de usuario

ARKSEN

ARKSEN 014-HG-14141-HR Manual de usuario

Black & Decker

Black & Decker PW1700SPX Manual de usuario

Kärcher

Kärcher 595 - SPARE Guía

Kranzle

Kranzle B 10 200 Manual de usuario

Stihl

Stihl RE 90 Manual de usuario

Husky

Husky HU80911 Manual de usuario

PowR-Quip

PowR-Quip PQ-2600 Manual de usuario