7
After use instructions
The machine should be stored in a frost-free room!
Pump, hose and accessories should always be emptied of
water prior to storing as follows:
Stop the machine (press the start/stop switch“O” and detach
water hose, high pressure hose and nozzle
Restart the machine and activate the trigger of the trigger
gun Let the machine run until no more water runs through
the trigger gun Stop the machine, unplug and wind up hose
and cable.
Place trigger gun, lance, nozzles and other accessories in the
holders of the machine. The hook can be used for storage
of the hose and cord 5, All accessories can be stored in the
washer after using.
!WARNING: Never start up a frozen machine. Frost
damages are not covered by the guarantee!
Environmental protection
Old appliances contain valuable materials that can be
recycled. Please arrange for the proper recycling of old
appliances. Please dispose your old appliances using
appropriate collection systems.
Maintenance, cleaner and repair
!WARNING! Always disconnect the electrical plug from the
socket prior to maintenance or cleaning.
To ensure a long and problem free working life, please take
the following advice: Wash out water hose, high pressure
hose, spray lance and accessories before mounting.
Clean the connectors of dust and sand. Rinse the detergent
spraying attachment after use.
Clean the nozzles.
Any repair should always be made in an authorized workshop
with original spare parts.
Cleaning of inlet lter
Clean the water inlet lter regularly once a month or more
frequently according to use. Carefully loosen the lter with
a screwdriver and clean it . Check that it is intact before re-
mounting it.
The inlet lter must always be tted inside the water inlet
pipe to lter out sand, limestone and other impurities, as they
will damage the pump valves.
CAUTION: Failure to t the lter will invalidate the warranty
Cleaning of air vents
The machine should be kept clean so as to let cooling air pass
freely through the machine vents.
6.3 Greasing of couplings
To ensure an easy connection and that o- rings do not dry up;
the couplings should be greased regularly.
Quick Connecting nozzles
• The 0º intense-jet nozzle (red) is an extremely
powerful nozzle that delivers a high-pressure, pencil point
jet stream. It is used to cut heavy dirt deposits
in a small, concentrated area. It is ideal for dissolving
stubborn substances, like tar and grease spots on
concrete, or for removing caked mud from equipment.
Use this nozzle to clean hard-to-reach areas including
the facades of 2-story buildings or the undersides of
lawn mowers and tractors.
NOTE: Care should be used when choosing the
right nozzle to avoid permanently gouging wood or
damaging fragile surfaces.
•Use the 15º fan-tip nozzle (yellow) for intense cleaning
jobs on hard surfaces. Applications include stripping
paint, removing oil stains, grease, heavy mildew stains,
and rust from steel. This nozzle should only be used in
areas that can withstand the high-pressure from this
nozzle.
•Use the 25º fan-tip nozzle (green) to clean home siding,
brick patios, wood decks, driveways, or sidewalks.
When using this nozzle, test a small area rst to avoid
surface damage.
• Use the 40º wide-spray tip nozzle (white) to clean items
such as cars, trucks, boats, patio furniture, or lawn
equipment.
• Use the Soap nozzle (black) for low-pressure detergent
application to clean equipment, remove mildew and
oxidation stains from houses, clean bricks or degrease
grimy surfaces.
NOTE: When using detergent, make sure that the
correct Soap nozzle (black) is installed. All of the other
colored nozzles will not work for detergent application.
6. Start at the top of the area to be rinsed and work down,
making sure to overlap the strokes.
!IMPORTANT! NEVER USE:
• Bleach, chlorine products, and other corrosive chemicals
• Liquids containing solvents
(e.g. paint thinners, gasoline,oils)
• Tri-sodium phosphate products
