Gefen Ex-tend-it 4x4 HDTV Matrix Manual de usuario

4x4 HDTV

Matrix

USER MANUAL

www.gefen.com

Technical Support:

Telephone (818) 772-9100

(800) 545-6900

Fax (818) 772-9100

Technical Support Hours:

8:00 AM to 5:00 PM Monday through Friday.

Write To:

Gefen Inc.

c/o Customer Service

20600 Nordhoff Street

Chatsworth CA 91311

www.gefen.com

[email protected]

Notice

Gefen Inc. reserves the right to make changes in the hardware, packaging and any

accompanying documentation without prior written notice.

The 4x4 HDTV Matrix is a trademark of Gefen Inc.

ASKING FOR ASSISTANCE

TABLE OF CONTENTS

Introduction / Operation Notes

Features

Panel Layout

Using the 4x4 HDTV Matrix

RMT16-IR Installation

Dip Switch Guidelines

IR Codes

RS-232 Interface

4x4 HDTV Matrix Rack Mount Diagram

Speciﬁcations

Terminology

Warranty

INTRODUCTION

Thank you for purchasing the 4x4 HDTV Matrix.

The 4x4 HDTV Matrix switches four HDTV sources to any four DVI displays.

The 4x4 HDTV Matrix switcher has four DVI inputs and four DVI outputs. Matrix input #1

and the DVI port of source #1 connects using a male to male DVI cable. The DVI port of

source #2 connects to DVI input #2. The DVI port of source #3 connects to DVI input #3.

The DVI port of source #4 connects to DVI input #4. There are four (4) DVI outputs con-

necting to four (4) different displays.

Note: The switching is done by using either the the RMT-16-IR remote control or through

theRS232port.The4x4 HDTVMatrix israck mountable.AnyHDTV withHDMI inputscan

be connected to the DVI outputs of the matrix by using a DVI to HDMI adapter or cable.

OPERATION NOTES

READ THESE NOTES BEFORE INSTALLING

OR OPERATING THE 4X4 HDTV MATRIX

• You should connect all the cables and power supply prior to connecting power to the

HDTV sources and 4x4 HDTV Matrix.

• When powering the sources, the display needs to point to the source input.

• The 4x4 HDTV Matrix is housed in a metal box for better RF shielding.

• The 4x4 HDTV Matrix works with all DVI and HDMI displays.

• The 4x4 HDTV Matrix only supports VIDEO signals.

• The 4x4 HDTV Matrix is fully HDCP compliant.

FEATURES

Features

• Allows any DVI/HDMI display to view any source at any time

• Allows any source to be displayed on multiple displays at the same time

• Maintains resolutions up to 1080p, 2K, and 1920x1200

• Maintains highest DVI single link video resolution

• Supports HDCP compliant devices

• DVI or DVI to HDMI cables are used to connect the inputs and the matrix output

• Each display's inputs can be switched with the IR remote control or through RS232

Includes:

(1) 4x4 HDTV Matrix

(4) DVI 6ft Male to Male Cables

(1) 24VDC Power Supply

(1) User Manual

(1) RMT-16IR Remote Control

(1) Rack Ears

PANEL LAYOUT

Display 1 LED

Indicator

Front Panel

RS232 Controller Port

Display 2 LED

Indicator Display 3 LED

Indicator Display 4 LED

Indicator

IR Sensor

IR Extender Eye Port Power Indicator

Back Panel

Connects to 24VDC

Power Supply

DVI Inputs DVI Outputs

Connect all the sources to the HDMI inputs on the 4x4 HDTV Matrix, using the

supplied cables.

Connect the HDMI/DVI displays to the outputs on the 4x4 HDTV Matrix.

Connect the 24VDC powersupply to the 4x4 HDTV Matrix

Controlling the 4x4 HDTV Matrix using the RMT16-IR:

Pressing Buttons... Switches...

1-4 Display 1 to view Source 1, 2, 3, or 4

5-8 Display 2 to view Source 1, 2, 3, or 4

9-12 Display 3 to view Source 1, 2, 3, or 4

13-16 Display 4 to view Source 1, 2, 3, or 4

*Note for computers connected to the HDTV Matrix - When your computer

boots up, it looks for an EDID (extended display identiﬁcation data) from the dis-

play to tell it what monitor is connected and what resolution to output. During boot

up of the computer you should have ONLY one output selected to one input at a

time so that the computer gets the EDID of the display that is selected. If you have

multiple outputs selected to one computer, the computer will read the EDID of the

last output selected to it. If all your displays are the same, or all displays are ca-

pable of running at the same resolution then this step does not matter.

USING THE 4X4 HDTV MATRIX

RMT16-IR Installation

1. Remove battery cover from the back of the RMT16-IR remote.

2. Verify that dip switches 1 & 2 are in the down (OFF) position.

3. Insert the battery, hold the battery so that you can see the positive side facing up. The

side that is not marked must be facing down.

4. Test the RMT16-IR remote by pressing ONLY one button at a time. The indicator light

on the remote will ﬂash once each time you press a button. WARNING: Do not press

multiple buttons simultaneously and do NOT press buttons rapidly. These actions will

cause the remote to reset and steps 1-4 will have to be repeated.

Note: The RMT16-IR ships with two batteries. One battery is required for operation, the

second battery is complimentary.

DIP SWITCH GUIDELINES

Extended display identiﬁcation data (EDID) is a data structure provided by a display to

describe its capabilities to any source that asks for it. The EDID includes manufacturer

name, product type, timings supported by the display, display size, luminance data, (for

digital displays only) pixel mapping data, supported audio channels and formats. This

information is used by the source to cater its output to resolutions and audio formats

that are supported by the display.

Additional EDID modes are available and conﬁgured using a combination of dip

switches 1, 2, and 5. Please refer below for the different EDID modes.

To access the Dip Switches, remove all screws from the bottom and sides of the

Gefen unit. Remove the hex screw heads from each side of the RS-232 and DVI ports.

Carefully slide the unit apart. The 8 Bank of Dip Switches are located on the main PCB.

Once adjustments are complete, slide the unit back together and replace all removed

screws.

EDID Mode 0 (Switch 1=OFF Switch2=OFF Switch5=ON)

-EDID is copied from the ﬁrst HDMI port

EDID Mode 1 (Switch 1=ON Switch2=OFF Switch5=ON)

-Same as Mode 0 and adds basic audio support

EDID Mode 2 (Switch 1=OFF Switch2=ON Switch5=ON)

-Same as Mode 0 and adds full audio support

EDID Mode 3 (Switch 1=ON Switch2=ON Switch5=OFF)

-EDID is generated based on the common video and audio features of all of the

connected devices

EDID Mode 4 (Switch 1=OFF Switch2=ON Switch5=OFF)

-Same as Mode 3 and adds basic audio support

EDID Mode 5 (Switch 1=ON Switch2=OFF Switch5=OFF)

-Same as Mode 3 and adds full audio support

EDID Mode 6 (Switch 1=OFF Switch2=OFF Switch5=OFF) DEFAULT

-EDID is generated based on the common video features of all of the connected

devices and the combined audio features of all of the connected devices

DIP SWITCH

EDID GUIDE

IR CODES

In the event of IR conﬂicts, please do the following:

1. Remove the battery cover from the back of the RMT16-IR remote.

2. Locate the Dip Switches above the batteries

3. Switch the Dip Switches on the RMT16-IR to any of the combinations pictured below.

4. Dip Switches 1 and 2 in the RMT16-IR correspond with Dip Switches 3 and 4 inside

the 4x4 HDTV Matrix respectively. Switch the switches inside the 4x4 HDTV Matrix to

match the same Remote Channel as the RMT16-IR. The 4x4 Matrix is now set to a new

IR Code.

Remote Channel 0:

Remote Channel 1:

Remote Channel 2:

Remote Channel 3:

Otros manuales para ex-tend-it 4x4 HDTV Matrix

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Conmutador de matriz de Gefen

Gefen

Gefen EXT-DVI-16416 Manual de usuario

Gefen

Gefen HDMI-CAT5-444 Manual de usuario

Gefen

Gefen EXT-HDMI1.3-444 Manual de usuario

Gefen

Gefen GEF-DVI-32432 Manual de usuario

Gefen

Gefen EXT-HDMI1.3-444 Manual de usuario

Gefen

Gefen EXT-HDMI1.3-444 Manual de usuario

Gefen

Gefen GEF-HDFST-MOD-16416-HDELR Manual de usuario

Gefen

Gefen EXT-HDMI-444 Manual de usuario

Gefen

Gefen EXT-VGAAUD-444 Manual de usuario

Gefen

Gefen EXT-HDMI1.3-444 Manual de usuario

Gefen

Gefen EXT-DVI-16416 Manual de usuario

Gefen

Gefen EXT-COMPAUD-44424 Manual de usuario

Gefen

Gefen EXT-HDMI1.3-848CPN Manual de usuario

Gefen

Gefen EXT-HDTV-444N Manual de usuario

Gefen

Gefen EXT-HDFST-848CPN Manual de usuario

Gefen

Gefen GTB-HDFST-848 Manual de usuario

Gefen

Gefen GEF-HDFST-848-8ELR Manual de usuario

Gefen

Gefen DVIKVM-444N Manual de usuario

Gefen

Gefen 4x4 HDMI Manual de usuario

Gefen

Gefen EXT-HDFST-848CPN Manual de usuario

Gefen

Gefen EXT-DVI-444DL Manual de usuario

Gefen

Gefen GEF-DVI-16416 Manual de usuario

Gefen

Gefen EXT-HDMI-CAT5-444 Manual de usuario

Gefen

Gefen GEF-DVI-848DL-PB Manual de usuario

Manuales populares de Conmutador de matriz de otras marcas

Broadcast Tools

Broadcast Tools SS 8.2 Manual de usuario

Altimium

Altimium MATF32 Manual de usuario

ALFAtron

ALFAtron ALF-MUK44N Manual de usuario

Monoprice

Monoprice Blackbird 15377 Manual de usuario

Kramer

Kramer XL 3216VS Manual de usuario

PTN

PTN FMX12 Manual de usuario

CYP

CYP nT15GX01 Manual de usuario

Kramer

Kramer VP-2x2 Manual de usuario

Kramer

Kramer Sierra Video 6432V5xl Manual de usuario

TESmart

TESmart HMA0402A40 Manual de usuario

Octava

Octava HD4XSTPMX Manual de usuario

Intelix

Intelix FLX-88 Instrucciones de funcionamiento

Kramer

Kramer LASSEN XL 3232S Manual de usuario

Roland

Roland XS-1HD Manual de usuario

Kramer

Kramer VS-66HDCPxl Manual de usuario

Atlona

Atlona AT-HDMI-22M Manual de usuario

Link

Link HD8X8 Manual de usuario

AMX

AMX AVS-OP-2020-117 Instrucciones y recetas

Gefen ex-tend-it 4x4 HDTV Matrix Manual de usuario

Manuales populares de Conmutador de matriz de otras marcas