GE 24991 Manual de usuario

Universal Remote

Instruction Manual

24991

Congratulations on your purchase of the 24991

Universal Remote Control. The 24991 is one of the

most easy to use remote controls available today.

With the 24991, juggling multiple remote controls is

a thing of the past! Your 24991 controls up to three

devices, including the most popular brands of TV,

VCR, DVD, SAT, CBL, and audio equipment.

Note: Some functions from your original remote

may not be controlled by this remote. Use the

original remote, if available, to control such

functions. Sometimes buttons other than described

in these instructions may actually perform the

function. For example, the CHAN and VOL

buttons might be used to navigate through menu

choices. We recommend you experiment with the

remote to identify if such situations pertain to your

equipment.

The 24991 is easy to use, easy to program, and

it gives you total control—at the touch of your

ngertips!

Table of Contents

Setup ..................................................................... 3

Battery Installation............................................ 3

Battery Saver.................................................... 3

Code Saver ...................................................... 3

Code Setup ...................................................... 3

Button Functions.................................................... 4

DVD Functions ................................................. 6

SAT Functions .................................................. 6

Code Entry............................................................. 7

Direct Code Entry ............................................. 7

Code Search .................................................... 8

Using Your Remote................................................ 9

 CodeIdentication............................................ 9

Shifted Functions............................................ 10

Controlling Devices with Power On and Off ... 10

Controlling Combo Devices............................ 10

VCR/DVD/DVR Punch-Through..................... 10

Volume/Mute Control and Punch-Through ..... 11

All Volume/Mute Control to any one Mode ..... 11

Setting any Mode for its own Volume/Mute .... 12

Troubleshooting................................................... 13

Battery Installation

1. On the back of the remote, push down on the

tab and lift the cover off.

2. Match the batteries to the + and - marks inside

the battery case, then insert 2 AAA Alkaline

batteries.

3. Press the battery cover back into place.

Battery Saver

Your remote automatically turns off if the buttons

are depressed more than 30 seconds. This will

save your batteries should your remote get stuck in

a place where the buttons remain depressed (e.g.,

between the sofa cushions).

Code Saver

You will have up to 10 minutes to change the

batteries in your remote without losing codes you

have programmed. However, do not press any

buttons until batteries are installed in the remote.

If buttons are pressed without batteries in the

remote, all codes will be lost.

Code Setup

The SETUP button is used to setup the remote.

You can either setup the remote using the code

for your brand of product, from the code tables (on

separate sheet), or you can search through the

libraryofcodesuntilyoundacodethatworks

for your product. Please refer to “Programming

with Code Search” page 9 for more information

on using the code search feature to learn how

to search through the library of codes for your

products. NOTE: You can store any kind of code

under any mode (except TV). I.E. you can store

a VCR code under the CABLE button, or a DVD

code under the SAT button, etc. However, you can

only store TV codes under the TV button.

Setup

VOLUME UP/DOWN

Changes the volume

level of the product,

normally the TV.

MUTE Turns off the

TV sound while the

picture remains.

OK Selects menu

items for the device

you are controlling.

RECORD, PLAY, STOP,

REW, FF, PAUSE VCR

control buttons operate your

VCR even when the remote

is set to operate the TV.

Also operates DVD Scan

-/+. Note the VCR keys also

control DVD when in DVD

Mode.

Some buttons on the remote might have functions that

are referred to by different names on the device you

are controlling. E.G. PREV CH may be called RECALL,

or ENTER may be called DISPLAY. These differences

depend on the brand and model of your product. Also,

this remote can only operate features that exist on your

product. E.G., your product must have PREV CH ability

for the PREV CH button to operate this feature.

TV, CBL/SAT, DVD/AUX Selects

product to be operated.

Button Functions

DOT

Used to select digital

channels, e.g., 5.3.

SETUP For setup.

SHIFT Accesses

shifted functions.

PREV. CH Returns to

the previously selected

channel. EXIT Exit On-

Screen Menus and/or

Return to previous On-

Screen selection.

NUMBERS

Enter numbers for direct

channel selection. Some

products require ENTER

to be pressed after chan-

nel selection.

ON-OFF Turns

device On or Off.

CHANNEL Up/Down

Changes the channels.

Button Functions, cont.

Note: The REC button must be pressed TWICE to record

from your VCR. For some brands of VCRs, you might

need to press the REC button once, then press it again

for three seconds.

INFO button brings up

DVD Display or Control

Menu for Chapter/Track/

Title number, Time re-

maining/elapsed indica-

tion, system information,

etc.

Selects the on-screen

menu.

ENTER

For some TV models,

used after direct chan-

nel number

entry to immediately

change to the

selected channel.

Red Indicator

Lights when any but-

ton is pressed.

INPUT

For some TVs, press

repeatedly to select

from available viewing

sources (antenna, cable

box, VCR, etc.).

CHAN+ and CHAN- buttons perform the “Page+”

and “Page-” function for on-screen Guide Menus

used by some Satellite systems.

INFO button brings up Satellite Display screen for

current Channel and system information.

MENU brings up the Satellite Menu screen - use

with the UP, DOWN, LEFT & RIGHT navigation

buttons.

OK button is used for on-screen Menu selection.

EXIT button is used to Exit or Clear on-screen

Menu displays.

INPUT button performs the Satellite TV/SAT func-

tion.

This remote controls many DVD functions. The

descriptions may vary from your original remote

descriptions.

REW and FF buttons control the speed of Fast

Forward and Reverse Playback respectively.

CHAN+/CHAN- buttons respectively locate the

succeeding or preceding Chapters or Tracks on a

disc.

INFO button brings up DVD Display or Control

Menu for Chapter/Track/Title number, Time remain-

ing/elapsed indication, system information, etc.

MENU brings up the DVD disc Menu screen - use

with the UP, DOWN, LEFT & RIGHT navigation

buttons.

OK button is used for on-screen Menu selection.

Note some DVD players require the Play button to

be used.

EXIT Exit On-Screen Menus and/or Return to pre-

vious On-Screen selection.

PLAY button is used to start Disc playback and for

Menu selection on some DVD players.

STOP button stops Disc playback.

PAUSE button pauses Disc playback - press PLAY

to resume.

INPUT brings up the DVD Players Setup Menu.

Note, not all DVD Players support all the functions

described above.

DVD Functions

SAT Functions

Direct Code Entry

Write your codes down here for easy reference

later.

1. Press and hold the SETUP button until

the red indicator stays on, then release

the SETUP button.

2. Press and release the desired mode

button (TV,DVD, etc.). The red indicator

blinks, then stays lit.

3. Enter the 4 digit code

from the code tables

(on separate sheet).

Note: after a valid

code entry, the red

indicator turns off. For

an invalid code, the

redindicatorashes.

4. With your device on, press ON/

OFF. If the device turns off, no

further programming is required.

Note: If some buttons do not

operate your equipment, try one of

the other codes for your brand.

Device Device stored Code

TV TV

CBL/SAT

DVD/AUX

Code Search

If your device does not respond after you have

tried all the codes for your brand, or if your brand is

not listed, try searching for your code by following

these steps.

1. Manually turn on the device (TV, DVD, etc.) to

be controlled.

2. Press and hold the SETUP button until

the red indicator stays on, then release

the SETUP button.

3. Press and quickly release the desired

mode button (TV, DVD, etc.). The red

indicator blinks off once.

4. Press the CHANNEL UP button

repeatedly (up to 300 times) until the

device to be controlled changes

channel. The red indicator blinks

off with each button press. If you

accidentally overshoot the code

required, press the CHANNEL

Most users will store DVD codes under the DVD

button, Cable codes under CABLE, etc. If (for

example) you want to store a DVD code under

CABLE,rstfollowtheprocedureforDirectCodeEntry

(page 8) and press CABLE in step 2 of Direct Code

Entry, then enter ANY DVD code in step 3 of Direct Code

Entry. Then follow the steps above for Code Search.

Note: If the device does not have a CHANNEL UP

button, use PLAY (DVD only) or POWER instead.

Code Search starts from the currently stored three digit

numberunderthatmode.Sometimestherstcode

that “works” with your device may only allow limited

functionality (e.g. the MENU button might not work).

There may be a code that performs more functions.

Continue the code search process until the best code is

found.

DOWN button to backtrack through the library

until the device changes channel. Pressing

CHANNEL UP changes direction to forward

again.

5. Press and release ENTER to install the code.

 CodeIdentication

TheCodeIdenticationFeatureallowsyouto

identify the 4 digit library code stored under your

devicekey.Forexample,ifyouwanttondout

what 4 digit code is stored under your TV device

key, follow the six steps below:

1. Press and hold the SETUP button until

the red indicator stays on. Release the

SETUP button.

2. Press and release the desired mode

button (TV, DVD, etc.). The red

indicator blinks, then stays lit.

3. Press and release the SETUP button.

The red indicator blinks once and

remains lit.

4. Tondtherstdigitfor

the code stored under the

mode key pressed in step

2, press each numeric

key from 0-9 in turn. The

number that causes the

indicator light to blink is

therstdigitinyourcode.

5. Tondtheseconddigit,repeatstep4.

6. Repeatstep4againtondthethirdandfourth

digits. This time the red indicator turns off and

stays off.

Using Your Remote

SHIFT

Press SHIFT (Setup) prior to the shifted key func-

tion e.g., for,

MENU - press and release SHIFT (Setup) then

MENU (Info).

UP - press and release SHIFT then UP (Chan+).

DOWN - press and release SHIFT then DOWN

(Chan-).

LEFT - press and release SHIFT then LEFT (Vol-).

RIGHT - press and release SHIFT then RIGHT

(Vol+).

OK - press and release SHIFT then OK (Mute).

EXIT - press and release SHIFT then EXIT (Prev.

Ch ). The red indicator blinks for each keypress.

Controlling Devices with Separate

Power On and Off Buttons

Some GE, RCA and ProScan models require

you to press the device button for more than one

second to turn the device on and the POWER

button to turn the device off.

Controlling Combo Devices

Some Combo devices (e.g. TV/VCR, TV/DVD,

DVD/VCR, etc.) will require you to set up two

different Mode buttons to control both parts of the

Combo device. For example, if you have a TV/

DVD Combo, you might need to set up one code

under the TV button to control the TV part AND a

separate code (under any other Mode button) to

control the DVD part.

VCR/DVD Punch-Through

This remote allows the 6 VCR/DVD transport

buttons (i.e. PLAY, PAUSE, STOP, FF, REWIND,

and REC) to Punch-Through control from any

Mode programmed with TV, SAT or Cable codes

to the last VCR, or DVD programmed Mode

you used. This feature will not operate if the

programmed TV, SAT or Cable code has its own

VCR transport button control e.g. a TV Combo,

SAT/PVR, etc.

Otros manuales para 24991

Tabla de contenidos

Manuales populares de Control remoto universal de otras marcas

Pronto

Pronto Peel Manual de usuario

Radio Shack

Radio Shack Wireless Remote Control System Manual de usuario

AUVIO

AUVIO Universal Home Theater Remote Manual de usuario

Philips

Philips Icon SRU4106 Manual de usuario

THOMSON

THOMSON ROC4309 Manual de usuario

Philips

Philips pm625S Manual de usuario

RCA

RCA RCU600WMS - Universal Remote Control Manual de usuario

Blackweb

Blackweb BWB17AV002 Manual de usuario

Marmitek

Marmitek DoorGuard 300 Manual de usuario

Chunghop

Chunghop RM-L618 Manual de usuario

Anderic

Anderic KTN828 Manual de usuario

Sunwave Tech.

Sunwave Tech. Touch Screen Remote Control Manual de usuario

Medion

Medion E74023 Manual de usuario

intensity

intensity RM02A Manual de usuario

Sky

Sky MY Manual de usuario

RCA

RCA RCU600M - Universal Remote Control Manual de usuario

Savant

Savant SUR-0500 Guía de referencia rápida

GDI

GDI GDI-WT2K Manual de usuario