GE 24110 Manual de usuario

Universal Remote

Instruction Manual

24110

Table of Contents

Introduction.................................................................. 3

Button Functions ....................................................... 4

Initial Setup................................................................... 6

Battery Installation ............................................. 6

Battery Saver......................................................... 6

Code Saver ............................................................. 6

Power-On default ................................................ 6

Code Setup ............................................................. 6

Direct Code Entry....................................................... 7

Code Search................................................................. 7

Code Identiﬁcation Feature.................................. 8

Setup ............................................................................... 9

Programming Combo Device Codes.......... 9

Controlling Combo Devices ............................ 9

Controlling Devices Requiring Separate

Power On and Off Buttons .............................. 9

VCR/DVD/DVR Punch-Through Feature..10

Volume/Mute Control and

Punch-Through Feature.................................10

Setting All Volume/Mute Control to

any one Mode .....................................................11

Setting any Mode to use its

own Volume/Mute Control............................11

Sleep Timer.................................................................12

Find/Page Feature ..................................................12

Troubleshooting.......................................................13

Introduction

Congratulations on your purchase of this

24110 Universal Remote Control. It is one

of the most unique looking, and easy to use

remote controls available today. With the

24110 juggling multiple remote controls is

a thing of the past! Your 24110 Universal

Remote controls up to 5 devices, including

the most popular brands of TV, VCR, DVD,

SAT, CBL, and audio equipment.

The 24110 comes with a convenient base/

stand that you can place the remote in when

you’re not using it. The base/stand also has

a Find/Page feature, which lets you quickly

ﬁnd the remote if you’ve misplaced it. You

simply press the Page key on the base and

the remote sounds with a tone, making it

easy to locate.

Other unique features for this remote are

described in the remainder of this manual.

Note: Some functions from your original

remote may not be controlled by the

24110 remote. Use the original remote,

if available, to control such functions.

Sometimes buttons other than described

in these instructions may actually perform

the function. For example, the CH and

VOL buttons might be used to navigate

through menu choices. We recommend you

experiment with the remote to identify if

such situations pertain to your equipment.

The 24110 Universal Remote is easy to

use, easy to program, and it gives you total

control—at the touch of your ﬁngertips!

Button Functions

10.

11.

12.

23.

22.

21.

20.

19.

18.

17.

16.

15.

14.

13.

Note: The Record button ( ) must be pressed TWICE to

record from your VCR. For some brands of VCRs, you might

need to press the Record button once, then press it again

for three seconds. Some buttons on the remote might have

functions that are referred to by different names on the

device you are controlling. E.g., PREV.CH may be called

RECALL, or ENTER may be called DISPLAY. These differences

depend on the brand and model of your product. Also,

this remote can only operate features that exist on your

product. E.g., your product must have PREV.CH ability for

the PREV.CH button to operate this feature.

1. ON-OFF: Turns device On or Off.

2. TV, VCR, DVD, SAT/CBL, AUDIO/AUX: Selects

product to be operated.

3. VOL UP/DOWN: Changes the volume level of the

product, normally the TV.

4. CH UP/DOWN: Changes the channels. Also

controls DVD/CD CHAPTER +/- track selection,

i.e., DVD/CD Track Skip Up/Down. Note the VCR

buttons also control the DVD when in DVD Mode.

5. SLEEP: Turns off the TV after a period of 1 to 99

minutes.

6. NUMBERS: Enter numbers for direct channel

selection. Some products require ENTER to be

pressed after channel selection.

7. ENTER: Used after direct channel number entry to

immediately change to the selected channel.

8. INFO: Displays on-screen channel information,

etc.

9. OK: Selects menu items for the device you are

controlling.

10. MENU: Displays the DVD disc menu screen. Use

with the UP, DOWN, LEFT & RIGHT navigation

buttons.

11. PIP: TV Picture-in-Picture control.

12. SWAP: Swaps TV PIP screens.

13. MOVE: Moves the position of the PIP screen.

14. EXIT: Exits On-Screen Menus and/or Returns to

previous On-Screen selection.

15. UP, DOWN, LEFT & RIGHT: Navigation buttons.

16. RECORD, PLAY, STOP, REW, FF, PAUSE: VCR

control buttons operate your VCR even when the

remote is set to operate the TV. Also operates

DVD Scan -/+.

17. GUIDE: Displays satellite or cable on-screen pro-

gram guide.

18 (•) Used for digital channels, e.g., 2.3.

19. INPUT Selects the video inputs of your TV if

equipped with that feature. TV/VCR: Operates

the same as the TV/VCR or antenna keys on your

original remotes.

20. PREV CH: Returns to the previously selected

channel or DVD repeat toggle.

21. MUTE: Turns off the TV sound while the picture

remains.

22. Red Indicator: Lights when any button is pressed.

23. SETUP: Used for setting up your remote.

Button Functions, cont.

Battery Installation

The 24110 Remote requires batteries for both the

remote and the remote base. Do the following to

install the batteries.

1. Push down on the tab on the back of the remote,

and lift the cover off.

2. Match the batteries to the + and - marks inside the

battery case, then insert 2 AAA alkaline batteries.

3. Press the battery cover back into place.

4. Open the battery door on the bottom of the base.

5. Match the batteries to the + and - marks inside the

battery case, then insert 2 AAA alkaline batteries.

6. Press the battery door back into place.

Battery Saver

Your remote automatically turns off if the buttons

are depressed more than 30 seconds. This will save

your batteries should your remote get stuck in a place

where the buttons remain depressed (e.g., between

the sofa cushions).

Code Saver

You have up to 10 minutes to change the batteries

in your remote without losing codes you have set up.

However, do not press any buttons until batteries are

installed in the remote. If buttons are pressed without

batteries in the remote, all the codes will be lost.

Power-On Default

The remote powers on in TV mode.

Code Setup

The SETUP button is used to setup the remote. You

can either setup the remote using the code for your

brand of product, from the code tables (on separate

sheet), or you can search through the library of codes

until you ﬁnd a code that works for your product.

Please refer to “Code Search” on page 7 for more

information on using the code search feature to learn

how to search through the library of codes for your

products.

NOTE: You can store any kind of code under any

mode (except TV). I.e., you can store a VCR code under

the CBL button, or a DVD code under the VCR button,

etc. However, you can only store TV codes under the

TV button.

Setup

Direct Code Entry

1. Press and hold the SETUP button until the red

indicator stays on, then release the SETUP button.

2. Press and release the desired mode button (TV,

VCR, etc.). The red indicator blinks, then stays lit.

3. Enter the 4-digit code from the code tables (on

separate sheet). Note: After a valid code entry, the

red indicator turns off. For an invalid code, the red

indicator ﬂashes.

4. With your device on, press CHANNEL UP. If the

device responds, no further programming is

required. Note: If some buttons do not operate

your equipment, try one of the other codes for

your brand.

Write your codes down here for easy reference later.

Code Search

If your product does not respond after you have tried

all the codes for your brand, or if your brand is not

listed, try searching for your code by following these

steps.

1. Manually turn on the device (TV, VCR, etc.) to be

controlled.

2. Press and hold the SETUP button until the red

indicator stays on, then release the SETUP button.

3. Press and quickly release the desired mode button

(TV, VCR, etc.). The red indicator blinks off once.

4. Press the CH UP button repeatedly (up to 300

times) until the device to be controlled changes

channel. The red indicator blinks off with each

button press. If you accidentally overshoot the

code required, press the CH DOWN button to

backtrack through the library until the device

changes channel. Pressing CH UP changes

direction to forward again.

5. Press and release ENTER to install the code.

Type Type stored Code

TV TV

VCR

DVD

SAT/CBL

Audio/AUX

Most users will store VCR codes under the VCR button,

DVD codes under DVD, etc. If (for example) you want

to store a VCR code under DVD, ﬁrst follow the proce-

dure for Direct Code Entry (previous page), and press

DVD in step 2 of Direct Code Entry, then enter ANY

VCR code in step 3 of Direct Code Entry. Then follow

the steps for Code Search on the previous page. Note:

If the device does not have a CHANNEL UP button,

use PLAY (VCR only) or ON-OFF instead. Code Search

starts from the currently stored 4-digit number under

that mode.

Code Search, cont.

Code Identiﬁcation Feature

The Code Identiﬁcation Feature allows you to identify

the four digit library code stored under your device

key. For example, if you want to ﬁnd out what 4-digit

code is stored under your TV device key, follow the six

steps below:

1. Press and hold the SETUP button until the red

indicator stays on. Release the SETUP button.

2. Press and release the desired mode button (TV,

VCR, etc.). The red indicator blinks, then stays lit.

3. Press and release the SETUP button. The red

indicator blinks off.

4. To ﬁnd the ﬁrst digit for the code stored under the

mode key pressed in step 2, press each numeric

key from 0-9 in turn. When the red indicator blinks

off the number you pressed is the ﬁrst digit for the

code you are searching for.

5. To ﬁnd the second digit, repeat step 4. This time

when the red indicator blinks off this is the second

digit.

6. Repeat step 4 to ﬁnd the third and fourth digits.

Programming Combo Device Codes

Some Combo devices (e.g., TV/VCR, TV/DVD, DVD/

VCR, etc.) will require you to set up two different Mode

buttons to control both parts of the Combo device.

For example, if you have a TV/DVD Combo, you might

need to set up one code under the TV button to

control the TV part AND a separate code (under any

other Mode button) to control the DVD part.

Controlling Combo Devices

Some Combo devices (e.g., TV/VCR, TV/DVD, DVD/VCR,

etc.) have separate buttons on the original remote to

select the part of the Combo device to be controlled.

For example, if your Combo device is a DVD/VCR then

its original remote might have separate DVD and VCR

buttons for selection of the Combo part you would

control. The equivalent button functions can be found

on your new remote by using the device Mode and

SETUP buttons.

Referring to “Code Search” on page 7, setup a device

Mode (e.g., DVD) with the correct code for your

Combo device. Assuming the DVD/VCR Combo device

is the example and its code is programmed under

DVD Mode, press and hold the DVD Mode button

for more than one second to send the DVD button

command. To send the VCR button command, quickly

press and release the SETUP button followed by

pressing and releasing the DVD Mode button. This

method can be applied similarly to all Combo devices

(e.g., TV/VCR, TV/DVD, DVD/VCR, etc.) and is available

for all Modes. Note this feature is not supported by all

codes.

Controlling Devices Requiring Separate Power On

and Off Buttons

Some devices (e.g., certain RCA TVs) require separate

Power On and Power Off buttons to turn the device

on and off. The equivalent button functions can be

found on your new remote by using the device Mode

and ON-OFF buttons. Referring to “Code Search” on

page 7, setup a device Mode (e.g., TV) with the correct

code for your device.

Assuming a TV device is the example and its code

is programmed under TV Mode, to turn your TV on,

press and hold the TV Mode button for more than one

second to transmit the Power On button command.

Setup, cont.

Controlling Devices Requiring Separate Power On

and Off Buttons, cont.

To turn the TV off, press and release the ON-OFF

button to transmit the Power Off button command.

This method can be applied similarly to any device

and is available for all Modes. Note this feature is not

supported by all codes.

VCR/DVD/DVR Punch-Through Feature

This remote allows the 6 VCR transport buttons (i.e.,

PLAY, PAUSE, STOP, FF, REWIND, and REC) to Punch-

Through control from any Mode programmed with

TV, SAT or Cable codes to the last VCR, DVD or DVR

programmed Mode you used. Normally other types

of remotes only punch-through (from another Mode)

on the 6 VCR buttons to the device programmed

under the VCR Mode button. This is not much use

if you are using a DVD programmed under a Mode

other than VCR. For example, if you have 3 DVD, VCR

or DVR devices programmed into this remote, the last

one you accessed on the remote will be the one that

has control of the 6 VCR transport buttons when in

any other Mode. This feature will not operate if the

programmed TV, SAT or Cable code has its own VCR

transport button control, e.g., a TV Combo, SAT/PVR,

etc.

Volume/Mute Control and Punch-Through Feature

This remote lets you select which device Mode

controls your Volume/Mute buttons. The remote

is initially set (factory default) for all device Modes

programmed with “Visual” codes (e.g., TV, VCR,

DVD, DVR, SAT & CABLE) and “Audio” codes (e.g., CD

& AUDIO) to use their own Volume/Mute control if

present. If the programmed “Visual” code has no

Volume/Mute operation of its own then those buttons

will punch-through control to the TV Mode device

without needing to change to TV Mode. Please refer

to the next page for more information.

Setup, cont.

Tabla de contenidos

Manuales populares de Control remoto universal de otras marcas

Pronto

Pronto Peel Manual de usuario

Radio Shack

Radio Shack Wireless Remote Control System Manual de usuario

AUVIO

AUVIO Universal Home Theater Remote Manual de usuario

Philips

Philips Icon SRU4106 Manual de usuario

THOMSON

THOMSON ROC4309 Manual de usuario

Philips

Philips pm625S Manual de usuario

RCA

RCA RCU600WMS - Universal Remote Control Manual de usuario

Blackweb

Blackweb BWB17AV002 Manual de usuario

Marmitek

Marmitek DoorGuard 300 Manual de usuario

Chunghop

Chunghop RM-L618 Manual de usuario

Anderic

Anderic KTN828 Manual de usuario

Sunwave Tech.

Sunwave Tech. Touch Screen Remote Control Manual de usuario

Medion

Medion E74023 Manual de usuario

intensity

intensity RM02A Manual de usuario

Sky

Sky MY Manual de usuario

RCA

RCA RCU600M - Universal Remote Control Manual de usuario

Savant

Savant SUR-0500 Guía de referencia rápida

GDI

GDI GDI-WT2K Manual de usuario