GE 51209 Manual de usuario

Do not use in wet locations

Personal Security

Motion Sensor

with Keypad

User Manual

Motion Sensing Alarm

With Remote Control

Low Battery Indicator

The Motion Sensing Alarm has a low

battery indicator light. When the batteries

need to be replaced, the indicator will

ﬂash slowly. Average battery life for

typical usage is up to one year.

Wall

Mount

Alarm/Chime Switch

Motion Sensing Alarm

Indicator Light

INSTALLING BATTERIES

The battery compartment is located on

the back of the unit.

Remove the battery compartment

screw and slide off cover in the

direction of the open arrow.

Insert (3) AA batteries (not included) .

Take care to note the polarity diagram

inside the battery compartment.

Replace the cover and secure screw.

Battery Compartment

Learn

Button

Learn

CREATING YOUR PERSONAL ALARM CODE

The 4-digit keypad allows you to set a

personal code for arming and disarming

the alarm.

Remove the battery compartment

screw and slide off cover in the

direction of the open arrow.

Press the LEARN button once; the

red indicator light on the front of the

alarm will blink for 15 seconds. During

this time, input your 4-digit code. A

beep will conﬁrm each input. The

unit will ﬂash a green light 3 times

to conﬁm your new 4-digit code has

been saved.

Replace the cover and secure screw.

INSTALLATION

The alarm is designed to be wall mounted

with the ball and socket mount (included).

The ball and socket mount will provide the

ﬂexibility to aim the motion sensor in a

particular direction.

Choose your desired location, such

as the corner of the room. This will

provide maximum coverage. NOTE:

The sensor has a 15-20 ft. detection

zone, with approximate angles of 110

degree horizontal x 70 degree vertical.

Recommended installation height is 6

to 8 feet.

110˚

20'

20'15'10'5'

Feet

6'-8'

10'

15'

70˚

Secure ball and socket mount to the

wall using either the provided wall

anchors or by screwing directly into a

wall stud. Once installed securely on

the wall, slide insert bracket of mount

into the back of the unit and lock

in place. The mount will click when

secured to the alarm.

OPERATING IN THE ALARM MODE

Locate the ALARM/CHIME switch on

the side of the alarm.

Slide switch to ALARM mode.

Arming the Alarm

Arm the alarm by pressing your 4-digit

code. A beep will sound after each

button is pressed.

When the 4-digit code is entered

correctly the unit’s indicator light

will ﬂash green once. If entered

incorrectly, the unit will sound and

the indicator light will ﬂash red three

times.

A red light will immediately begin to

ﬂash indicating the 45-second exit

delay has started. The delay allows

time for you to leave the protected

area without triggering the alarm.

When motion is detected, the alarm

unit will sound a short tone and a red

light will ﬂash. The alarm will activate

in 30 seconds. The siren will sound

for 30 seconds (unless disarmed by

the remote) and then turn off. In 15

seconds the alarm will check for

motion. If motion is detected, the siren

will sound again. The cycle will repeat

until the unit is disarmed with the

remote.

Disarming the Alarm

When returning to the protected area,

simply enter your 4-digit code within

30 seconds to disarm the alarm.

When the fourth digit of your code is

entered, the unit will respond with two

tones and the indicator light will ﬂash

green twice.

The unit will beep once if motion is sensed.

If the correct code is not entered within

30 seconds, the alarm will sound. Enter

correct code anytime after the alarm has

sounded to deactivate. NOTE: To test, a

cloth can be used to cover the alarm to

reduce risk of hearing damage.

Incorrect Code

If an incorrect code is entered the unit will

sound a louder beep and the indicator

light will ﬂash red 3 times. Re-enter

correct code after indicator light stops

ﬂashing.

OPERATING IN THE CHIME MODE

The chime is used to notify you when

motion is sensed in the area.

Slide switch to CHIME mode; the

chime will sound once.

Activating the Chime:

The chime will go off immediately

when motion is sensed. No code is

required. The motion sensor will retest

the area 15 seconds after chime

sounds.

•

Tabla de contenidos

Otros manuales de Sistema de seguridad de GE

GE 60-960-95 Manual de usuario

GE NX-108E - Security NetworX NX-4 System Manual de usuario

GE Allegro 60-874-95R Manual de usuario

GE 50246 - Smart Home Door Stop Alarm Manual de usuario

GE Concord 4 Manual de instrucciones

GE TX-7201-05-1 Manual de usuario

GE 45413 Manual de usuario

GE 4 Series Manual de usuario

GE Interlogix 60-875 Simon Manual de usuario

GE 45133 Manual de usuario

GE 45131 Manual de usuario

GE AL-1291 Point ID Manual de usuario

GE Security Pro 500 Manual de usuario

GE SIMON XT Manual de usuario

GE Concord 4 Series Manual de usuario

GE 868 GEN2 Manual de usuario

GE 45129 Manual de usuario

GE SIMON XT Manual de usuario

GE CareGard Manual de usuario

GE NetworX Manual de usuario

GE Supra KeySafe Manual de usuario

GE 600-1021-95R Manual de usuario

GE NX-10 Manual de usuario

GE SIMON XT Manual de usuario

Manuales populares de Sistema de seguridad de otras marcas

Inner Range

Inner Range Concept 2000 Manual de usuario

Climax

Climax Mobile Lite R32 Instrucciones de montaje

CADDX

CADDX NX-6 Manual de usuario

FBII

FBII XL-31 Series Manual de usuario

Johnson Controls

Johnson Controls PENN Connected PC10 Manual de usuario

Aeotec

Aeotec Siren Gen5 Manual de usuario

Blaupunkt

Blaupunkt SA 2700 Manual de usuario

IDEAL

IDEAL Accenta Manual del propietario

AJAX

AJAX DoubleButton Manual de usuario

Swann

Swann SW-P-MC2 Manual de usuario

Ecolink

Ecolink Siren+Chime Manual de usuario

Digital Monitoring Products

Digital Monitoring Products XR150 Manual de usuario

EDM

EDM Solution 6+6 Wireless-AE Manual de usuario

Highway Safety Group

Highway Safety Group EA401 Manual de usuario

Siren

Siren LED GSM Manual de usuario

Detection Systems

Detection Systems 7090i Instrucciones de montaje

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Manual de usuario

Siemens

Siemens FDM273 Manual de usuario