GE Concord 4 Manual de usuario

GE Concord 4 Quick Setup Guide

For more detailed information, please see the GE Installation Manual.

1. Planning your system

a. Wired Zones: A hardwired zone can consist of 1 or more sensors in a loop.

Each zone loop must consist of similar sensors, that can be programmed the

same.

i. Normally Open Sensors ormally open sensors have an “Open”

circuit until the sensor is tripped, it will then close the circuit. This

change is detected by the panel, and causes the alarm. These sensors

get wired in Parallel. (See Wiring Diagrams)

ii. Normally Closed Sensors ormally closed sensors have a “Closed”

circuit until the sensor is tripped, it will then open the circuit. This

change is detected by the panel, and causes the alarm. These sensors

get wired in Series. (See Wiring Diagrams)

iii. Powered Sensors Powered Sensors, such as Motion detectors, Glass

Break Detectors will require a 4 conductor wire. Two wires are for

power connections, and two wires

are for the zone connections.

b. Wireless Zones Unlike wired zones, for

each wireless sensor you will use 1

wireless zone. Each sensor is programmed

to a zone with all information for that

individual sensor.

2. Wiring the System

a. Keypads All Keypads get wired to Pins 3,

4, 5, and 6. the system will automatically

detect the number of keypads connected

to the system. Match the colors used on

each pin, to the corresponding connections

on the keypad. (See Diagram to Right)

b. Sensors

i. Normally Open Sensors Check

the product documentation – If the

Loop Type is “ O” or “ ormally

Open” then the sensors should be

wired in Parallel with the zone.

(See Diagram On Last Page)

ii. Normally Closed Sensors Check

the Product Documentation – If the

Loop Type is “ C” or “ ormally

Closed” then the sensors are wired in Series with the zone (See

Diagram to On Last Page)

3. Programming The System

a. Entering Programming Mode

1. Make sure the system is disarmed in all partitions.

2. Press 8 + 4321 + 0 + 0. The display shows “SYSTEM PROGRAMMING”.

b. Programming Hardwired Zones

i. Zone Groups are pre-programmed for the 8 hardwired zones.

1. Entry Exit Delay – For Doors that require a delay for entry or

exit

2. Instant Interior Follower – For motion detectors that will

arm instantly.

3. Instant Perimeter – For all doors/window sensors, glass

break detectors that do not require a delay.

ii. **Change the “Pre-Programmed” Zone Settings

1. Once you are in the programming mode, press B until the

display shows “Sensors”, and press # to select

2. ow Press B until the display shows “Edit”, and press # to

select.

3. Press A or B to scroll to the zone number you desire to change

press # to select

4. Enter the desired partition number, and then press #. (Most Applications the

Partition is always 1) The display shows the new partition assignment.

5. Press A or B and the display shows SENSOR GROUP nn (current group

assignment)

6. Enter the desired group number, (See appendix B in Installation Manual) then

press #. The display shows the new group assignment.

c. Programming Wireless Zones

i. With the display showing SENSORS, press # and the display shows “Learn Sensors”

ii. Press # and the display shows Sensor PTN 1

iii. Press # to select partition 1 or press 2, 3, 4, 5, or 6 + # to select the desired partition

(Typically is always Partition 1). The display should show “Sensor Group 0”

iv. Enter the desired sensor group number and press # to select (see Table B1 in “Appendix

B” for a description of all sensor group characteristics). The display shows TRIP

SENSOR nn, where nn is the displayed (next available) sensor number.

v. To change the displayed sensor number, enter the desired sensor number + #. The desired

sensor number is displayed.

vi. With the desired sensor number displayed, use the guidelines in Table 6 to force the

sensor or zone you are adding (learning) into the panel memory to send a signal to the

panel.

vii. To add another sensor to the same sensor group and partition, go back to step 5.

viii. To add sensors to another sensor group or partition, press * twice and go back to step 1

(LEARN SENSORS).

d. Changing Wireless Zone Settings:

i. If you need to change a zone setting – Enter Programming Mode, Press B to Scroll the

menu. Select “Sensors” # “Edit” # Select the Zone you wish to Edit, and make the desired

changes pressing # to save the desired changes.

e. Exiting Programming Mode

i. After all installer/dealer programming is completed, use the following procedure to exit

programming mode.

To exit programming mode:

1. Press * until the display shows SYSTEM PROGRAMMING.

2. Press A or B until the display shows EXIT PROGRAMMING READY.

3. Press # and the touchpad displays the TIME AND DATE.

f. Using The System

i. Setup User Codes:

1. To Enter User-Programming Mode

a. Press 9 then the 4 digit Master Code (Default is 1234)

2. Scroll Menu using the B Button until you reach “User”

3. With the display showing USER CODES, press # and the display shows REGULAR

USER CODES.

4. Press # and the display shows USER nnn (first available user number).

5. Press A or B to select the desired user number, and then press #. The display

shows USER nnn - nnnn.

6. With the desired user number displayed, enter a 4-digit user code. The display

flashes the entered code. Press # and the display shows USER nnn - nnnn (new

code).

Zone Wiring Diagrams

Otros manuales para Concord 4

Tabla de contenidos

Otros manuales de Sistema de seguridad de GE

GE Security Pro 1000 Manual de usuario

GE 600-1064-95R b Manual de usuario

GE Deluxe 45117 Manual de usuario

GE SmartCom CC-SCRS01 Manual de usuario

GE 60-960-95 Manual de usuario

GE AL-1291 Point ID Manual de usuario

GE SIMON XT Manual de usuario

GE VT71230-R3 Guía de instalación

GE SuperBus 2000 Manual de usuario

GE Interlogix 60-875 Simon Manual de usuario

GE 60-806-95R-16Z - Security Concord Express System Control... Manual de usuario

GE Security Pro 500 Manual de usuario

GE Advent Manual de usuario

GE 13-949 Manual de usuario

GE ActiveKEY Manual de usuario

GE Interlogix 60-875 Simon Manual de usuario

GE SIMON XT Manual de usuario

GE 610 Manual de usuario

GE DeluxeDoorAlarm Manual de usuario

GE AS272 Manual de usuario

GE NX-10 Manual de usuario

GE 8RP Board Instrucciones de montaje

GE 868 GEN2 Manual de usuario

GE ARITECH AS399 Manual de usuario

Manuales populares de Sistema de seguridad de otras marcas

Inner Range

Inner Range Concept 2000 Manual de usuario

Climax

Climax Mobile Lite R32 Instrucciones de montaje

CADDX

CADDX NX-6 Manual de usuario

FBII

FBII XL-31 Series Manual de usuario

Johnson Controls

Johnson Controls PENN Connected PC10 Manual de usuario

Aeotec

Aeotec Siren Gen5 Manual de usuario

Blaupunkt

Blaupunkt SA 2700 Manual de usuario

IDEAL

IDEAL Accenta Manual del propietario

AJAX

AJAX DoubleButton Manual de usuario

Swann

Swann SW-P-MC2 Manual de usuario

Ecolink

Ecolink Siren+Chime Manual de usuario

Digital Monitoring Products

Digital Monitoring Products XR150 Manual de usuario

EDM

EDM Solution 6+6 Wireless-AE Manual de usuario

Highway Safety Group

Highway Safety Group EA401 Manual de usuario

Siren

Siren LED GSM Manual de usuario

Detection Systems

Detection Systems 7090i Instrucciones de montaje

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Manual de usuario

Siemens

Siemens FDM273 Manual de usuario