Galvin Engineering Safe-Cell 50150 Hoja de instrucciones

Version 1, 30 August 2018, 1 of 4

Safe-Cell® Prison Basin Set

PRODUCT CODE:

- 50150

SPECIFICATIONS

 The Safe-Cell® Timeflow Push Button Valve is used in prisons, detention centres, high risk institutions,

sporting facilities, schools and public area applications

 Once activated, this timed flow product will allow water to flow for approximately 15 seconds*

 Designed for easy bench installation (maximum thickness 10mm)

 Time is based on set at 500kPa, 4LPM @ 22˚C. Time is affected by temperature, flow rate and pressure

 Chrome plate finish

Note: This is a single temperature product, so if warm water is required this needs to be premixed prior to

reaching the valve. This can be done by using a CliniMix® Thermostatic Mixing Valve.

IMPORTANT: All Safe-Cell® prison taps are tested in accordance with AS/NZS 3718 and leave our

premises in good working order.

TECHNICAL DATA

Inlet ½” BSP – Male

Outlet Dome Outlet

Headwork Time flow cartridge

Working Pressure Range (kPa) Min 100

Max 500

Maximum Working Temperature (°C) Min 5

Max 70

Nominal Flow Rate (LPM) 2.55

Construction Brass

Finish Chrome

NOTE: Galvin Engineering continually strive to improve their products. Specifications may change without

notice.

TOOLS REQUIRED

 Power drill

 Spanner or adjustable crescent

Version 2, 30 August 2018, 2 of 4

PRE-INSTALLATION

MOUNTING DETAILS

 If the mounting holes do not already exist, mark out and drill the holes in the bench/trough, as shown

in rough-in dimensions.

Note: Supplied flexi hose length is 450mm long. Maximum distance between outlet and push button

adjustment is 420mm.

INSTALLATION

INSTALLATION COMPLIANCE: Galvin Engineering products must be installed in accordance with these

installation instructions and in accordance with AS/NZS 3500, the PCA and your local regulatory

requirements. Water and/or electrical supply conditions must also comply to the applicable national and/or

state standards. Failing to comply with these provisions shall void the product warranty and may affect the

performance of the product.

IMPORTANT: Whilst our product designs take into account a broad range of installation types and surfaces,

it is important that surfaces which fixtures are mounted to are flat and free from defect. This is especially

important when installing product ranges that have been designed for correctional and health facilities, where

special attention is required to minimise ligature points and areas for concealment of contraband. In addition

to ensuring the products are fitted securely and in accordance with the following instructions, consideration

shall be given to the use of non-pick mastics such as BASF Sonolastic “Ultra” to ensure a high quality and

safe installation.

15.0

420 MAX

BENCH / TROUGH

FLOW DIRECTION

PUSH BUTTON ASSEMBLY

WATER HOSE 15F R/CONE

1/2"BSP

HEX W/ELBOW x 450mm LONG

1/2"BSP

ISOLATING/

REGULATING

BALL VALVE

BASIN OUTLET 175

Version 2, 30 August 2018, 3 of 4

1. Fit push button & basin outlet

 Fit the push button and basin outlet into the bench.

 Ensure the sealing o-ring is placed underneath the

push button and outlet body and the anti-rotation pin

locates properly.

 Secure underneath with the supplied cup washer and

back nut.

2. Assemble valve body

 Assemble the valve body to the push

button.

 Ensure to apply thread tape for sealing.

Take care not to over-tighten.

3. Fit flexi hose

 Connect water supply to isolation valve inlet.

4. Testing

 Push the button and ensure that there is

flow from the outlet.

 Inspect the tap and check for any leaks.

 Adjust flow with isolation valve, so

required flow is achieved

Version 1, 30 August 2018, 4 of 4

TROUBLESHOOTING

PROBLEM CAUSE RECTIFICATION

Inconsistent

flow

Blocked flow restrictor Remove isolation valve, remove flow restrictor & clean

with water

Dirt in the top assembly cartridge Remove cartridge, clean with water and re-grease

spindle if required.

Continuous

flow

Top assembly cartridge loose or

internally obstructed or damaged.

Remove cartridge, clean with water and re-grease

spindle if required.

Water is not

flowing from

tap

Supply not on Turn water on

Blocked flow restrictor Remove flow regulator from tap and remove debris.

Install an inline strainer to stop further blockages.

Rate of flow

inadequate

The flow restrictor may not be

satisfactory due to inadequate supply

pressure

Remove flow restrictor and replace with a flow restrictor

of different capacity to suit (available from Galvin

Engineering)

Button hard

to press The mains pressure may be too great Reduce to below 500kPa (70PSI), re-grease spindle if

required

In the absence of a legal or industry definition of anti-ligature or ligature resistant products, when we use these terms, we are referring to

products that are designed and manufactured with the intention of reducing the risk of ligature attachment to the product(s).

Galvin Engineering Pty Ltd will always endeavour to design and test our anti-ligature product(s) to reduce the risk of product ligature attachment that may result in

serious injury or death.

Whilst all reasonable measures are taken at the time of design, the anti-ligature design of the products are not intended to and will not:

a. Replace protective measures that need to be taken in the specific circumstances of usage;

b. Substitute the need for supervision of those who may be at risk;

c. Protect and or prevent those at risk against any self-harm instances that may occur when installed; and

d. Protect and or prevent injury when the risks where unknown to us at the time of the design of the product(s).

Galvin Engineering Pty Ltd does not offer and does not represent or warrant that any product(s) for sale that are ligature-free.

Therefore, Galvin Engineering will not be liable for any claims, loss, or damages arising from ligature attachment on our products. It is the purchaser's responsibility

to ensure that products purchased and installed are suitable for the environments in which they are installed, and suitable supervision and protective measures are

in place to protect those at risk.

WARRANTY

The warranty set forth herein is given expressly and is the only warranty given by the Galvin Engineering Pty

Ltd. With respect to the product, Galvin Engineering Pty Ltd makes no other warranties, express or implied.

Galvin Engineering Pty. Ltd. hereby specifically disclaims all other warranties, express or implied, including but

not limited to the implied warranties of merchantability and fitness for a particular purpose.

Galvin Engineering Pty Ltd products are covered under our manufacturer’s warranty available for download

from www.galvinengineering.com.au Galvin Engineering Pty Ltd expressly warrants that the product is free

from operational defects in workmanship and materials for the warranty period as shown on the schedule in

the manufacturer’s warranty. During the warranty period, Galvin Engineering will replace or repair any

defective products manufactured by Galvin Engineering without charge, so long as the terms of the

Manufacturer’s warranty are complied with.

The remedy described in the first paragraph of this warranty shall constitute the sole and exclusive remedy for

breach of warranty, and Galvin Engineering Pty Ltd shall not be responsible for any incidental, special or

consequential damages, including without limitation, lost profits or the cost of repairing or replacing other

property which is damaged if this product does not work properly, other costs resulting from labour charges,

delays, vandalism, negligence, fouling caused by foreign material, damage from adverse water conditions,

chemical, electrical or any other circumstances over which Galvin Engineering has no control. This warranty

shall be invalidated by any abuse, misuse, misapplication, improper installation or improper maintenance or

alteration of the product.

Otros manuales de Producto de plomería de Galvin Engineering

Galvin Engineering

Galvin Engineering CliniMix CP-BS Hoja de instrucciones

Galvin Engineering

Galvin Engineering CliniMix WM-PMSKIT Hoja de instrucciones

Galvin Engineering

Galvin Engineering CliniLever TCWMC80CC Hoja de instrucciones

Galvin Engineering

Galvin Engineering WaterMark 46638 Hoja de instrucciones

Galvin Engineering

Galvin Engineering Ezy-Drink 35188X Manual de usuario

Galvin Engineering

Galvin Engineering CliniMix CP-BS WM-TMVPMB Hoja de instrucciones

Galvin Engineering

Galvin Engineering GalvinSafe 190.81.12.32 Hoja de instrucciones

Galvin Engineering

Galvin Engineering GalvinSafe 190.42.11.90 Hoja de instrucciones

Galvin Engineering

Galvin Engineering GalvinCare CP-BS Lead Safe 121.35.64.00 Manual de usuario

Galvin Engineering

Galvin Engineering 170.01.13.00 Hoja de instrucciones

Galvin Engineering

Galvin Engineering Capstan 175.91.00.03 Manual de usuario

Galvin Engineering

Galvin Engineering CliniLever TCBTC80CC Manual de usuario

Galvin Engineering

Galvin Engineering GalvinSafe 190.80.10.12 Hoja de instrucciones

Galvin Engineering

Galvin Engineering Haws SP220SS Hoja de instrucciones

Galvin Engineering

Galvin Engineering 656512 Hoja de instrucciones

Galvin Engineering

Galvin Engineering Ezy-Drink CP Lead Safe 2 in 1 Bottle Filler & Bubbler Hob... Hoja de instrucciones

Galvin Engineering

Galvin Engineering GalvinSafe 190.41.12.12 Hoja de instrucciones

Galvin Engineering

Galvin Engineering GalvinSafe 190.42.11.12 Hoja de instrucciones

Galvin Engineering

Galvin Engineering GalvinCare CP-BS Hoja de instrucciones

Galvin Engineering

Galvin Engineering Ezy-Drink 316 TDBFXEB Hoja de instrucciones

Galvin Engineering

Galvin Engineering CliniMix Lead Safe 100.00.71.00 Hoja de instrucciones

Galvin Engineering

Galvin Engineering Ezy-Drink 85326X Hoja de instrucciones

Galvin Engineering

Galvin Engineering BS Capstan SBA Hoja de instrucciones

Galvin Engineering

Galvin Engineering Ezy-Push CP-BS Lead Safe Manual de usuario

Manuales populares de Producto de plomería de otras marcas

Weka

Weka 506.2020.00E Instrucciones de funcionamiento

Kohler

Kohler K-6228 Instrucciones de montaje

UBERHAUS DESIGN

UBERHAUS DESIGN 75175017 Manual de usuario

American Standard

American Standard DetectLink 6072121 Manual de usuario

Uponor

Uponor Contec TS Manual de usuario

Pfister

Pfister Selia 49-SL Manual de usuario

Fortis

Fortis VITRINA 6068700 Manual de usuario

Fortis

Fortis MILANO 78211JS Manual de usuario

Kohler

Kohler K-12183 Instrucciones de montaje

Maxxus

Maxxus MX-M206-01 Manual de usuario

Moen

Moen 5922 Series Manual de usuario

Viega

Viega Prevista Pure 8512 Manual de usuario

Kohler

Kohler Centerset K-15240 Instrucciones de montaje

Viega

Viega Prevista Dry 8522.33 Manual de usuario

Sanela

Sanela Lema SLP 59RB Manual de usuario

Elkay

Elkay EDF15AC Manual de instalación

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Manual

baliv

baliv WT-140 Manual de usuario