American Standard DetectLink 6072121 Manual de usuario

M985145 SKU# 607X121 EN (8/23)

6072121/607B121

American Standard is devoted to making life,

in the heart of your home, better every day…

…so, thank you for inviting us in! With the very best in kitchen

and bathroom products, we are here to help make your life

happier, healthier and simpler. Our commitment to quality,

innovation and performance has made us part of your everyday

routine for nearly 150 years, and we look forward to being a

part of your life for many years to come.

Learn more at www.AmericanStandard.com

Try the easy-scan QR code to quickly enter

your information or ﬁnd your product’s

detailed warranty here:

www.AmericanStandard.com/warranty

Registering allows you to keep your product information

safe, and us the ability to contact you in the event of a

product recall or any news about your purchase.

And if ever you have a question or need help…?

Call us at 1-855-815-0004

OWNERS MANUAL

IoT DetectLnk™Exposed

Toilet Flush Valve

6072121 / 607B121

Image shown may vary from product purchased.

INSIDE THE BOX (BATTERY VERSION)

Battery Power Kit PK01.WRK

POWER KITS SOLD SEPARATELY

60780XX FOR BATTERY VERSIONS

Vacuum Breaker

Tube

Stop Valve

Flush Valve

INSIDE THE BOX (AC VERSION)

Hard-Wired AC

Power Kit Hard-Wired AC &

Multi-AC Power Kit

PK00.HAC / PK00.BBU PK00.MAC / PK00.HAC

PK00.BBU

POWER KITS SOLD SEPARATELY

607BXXX/607B0XX FOR AC VERSIONS

Vacuum Breaker

Tube

Stop Valve

Flush Valve

NOTE TO INSTALLER: Please give this manual to the customer after installation.

To learn more about American Standard Selectronic®Products visit our website at:

www.americanstandard-us.com or e-mail us at: ASdetectlnk@lixil.com

For Parts, Service, Warranty or other Assistance,

please call (844) CRT-TEAM / (844) 278-8326

(In Toronto Area only: 1-905-306-1093)

PRIOR TO INSTALLATION

Note: Prior to installing the DetectLnk™ Flush Valve the following items must be

installed.

1. Urinal/Toilet

2. Drain line

3. Water supply line

IMPORTANT:

• All plumbing and electrical wiring should be installed in accordance with applicable

codes and regulations.

• The use of water hammer arrestors is strongly recommended for commercial applications.

All piping behind the walls should be properly secured and fastened.

• Water supply lines must be sized to provide an adequate volume of water for each ﬁxture.

• Flush all water lines prior to operation Dirt and debris can cause ﬂush valve to run

continuously.

• With the exception of Stop Valve Inlet, DO NOT use pipe sealant or plumbing grease

on any valve component or coupling!

• Protect the chrome or special ﬁnish on the Flushometer. DO NOT USE toothed tools on

ﬁnished surfaces to install or service these valves. Also see “Care and Cleaning”

section of this manual.

• This product contains mechanical and/or electrical components that are subject to normal

wear. These components should be checked on a regular basis and replaced as needed to

maintain the valve’s performance.

Consult xture manufacturer for minimum pressure requirements. Most High

Efciency water closets require a minimum owing pressure of 25 psi (172 kPa).

Many building codes and the ASME A112.19.2 xture standard list Maximum

static water pressure as 80 PSI (552 kPa).

10'

RECOMMENDED TOOLS

Teﬂon Tape

Installation steps will indicate which tools should be used with asscociated letter

Flat Blade

Screwdriver

Adjustable

Wrench

Hacksaw

Tape Measure

Tubing Cutter

File

2.5 & 1.5 mm

Hex Wrench

Solder & Torch

Note: Install Optional Sweat Adapter (Supplied) for

copper pipe supply line.

1. Measure the distance (A) from the ﬁnished wall to the

center of the inlet spud on the ﬁxture.

2. Cut the supply pipe 1-1/4” (A-B=C) shorter than the

measurement taken in Step 1. File any rough edges

off the end of the supply pipe.

3. Clean the end of the supply pipe. Push the threaded

Adapter until it is seated against the internal stop.

Sweat the Adapter to the pipe.

CENTER LINE OF

FIXTURE SPUD

FINISHED WALL

FILE EDGES

SOLDER

ADAPTER

32mm

(1-1/4")

(A-B)= B

CLEAN

1INSTALL SWEAT ADAPTER

2INSTALL COVER TUBE, WALL ESCUTCHEON AND STOP VALVE

Turn off hot and cold water

supplies before beginning.

Fig. 4a

Fig. 4b

Fig. 4c

TEFLON TAPE

FINISHED WALL

FLUSH VAVLE INSTALLATION

1. Measure from ﬁnished wall to ﬁrst thread of Adapter

or threaded supply pipe (dimension “X”). Cut

COVER TUBE (1) to length (X). Apply Teﬂon Tape to

the threaded end of the Adapter or supply pipe.

2. Push WALL ESCUTCHEON (2) onto the COVER

TUBE (1). Slide both onto the SUPPLY PIPE (3).

3. Push the COVER TUBE (1) in to expose the threads

of the supply pipe. With a wrench thread the STOP

VALVE (4) onto the SUPPLY PIPE (3). Align and

tighten.

4. Pull COVER TUBE (1) against STOP VALVE (4) and

push WALL ESCUTCHEON (2) against ﬁnished wall.

G I D E

A C D F

3FLUSH OUT SUPPLY LINES

CLOCKWISE CLOSES

STOP VALVE

COUNTER-CLOCKWISE

OPENS STOP VALVE

REMOVE COVER

1. Remove STOP VALVE COVER (1) from STOP

VALVE (2).

2. Open STOP VALVE (2) with a ﬂat blade screwdriver.

3. Turn on water supply to ﬂush line of any debris or

sediment.

4. Close STOP VALVE (2) and replace STOP VALVE

COVER (1).

4a INSTALL VACUUM BREAKER TUBE: APPLICABLE FOR STANDARD CERAMICS

Note: Step 4a is only applicable if using standard

ceramics. If using IoT Ceramics, skip to step 4b.

1. Insert VACUUM BREAKER TUBE (1) through

HEX NUT (4), FLUSH VALVE BOTTOM COVER

(2), and SPUD COVER (3).

2. Thread SPUD COVER (3) on to the toilet base.

Note: Ensure that the O-ring is properly seated in the

base of HEX NUT (4).

1. Slide SPUD COVER (1) over HEX NUT (2).

2. Secure SPUD COVER (1) by tightening SET SCREW (3).

INSTALL VACUUM BREAKER TUBE: APPLICABLE WITH ASA IOT CERAMICS

C D

Note: Step 4b is only applicable if using ASA IoT Ceramics.

Otherwise, refer to step 4a.

1. Separate HEX NUT (4) from SPUD COVER (7).

2. Thread WIRE (5) through FLUSH VALVE BOTTOM COVER

(2) and SPUD COVER (3).

3. Insert VACUUM BREAKER TUBE (1) through

the FLUSH VALVE BOTTOM COVER (2), SPUD COVER (3),

HEX NUT (6), AND HEX NUT (4).

4. Thread HEX NUT (4) on to the Toilet Base.

Note: Ensure that the O-ring is properly seated in the base of

HEX NUT (4).

Note: Vacuum breaker tube can be shortened by up to 1-1/2"

if desired.

Note: Spud Cover (3) and Wire Cover is only available in the

ASA IoT Ceramics Package.

4b CONTINUED

1. Thread WIRE (1) through the back of FLUSH

VALVE BODY (2).

Note: There is a small hole on the top back of the

brass body for the wire head to ﬁt through.

WIRE HOLE

BOTTOM VIEW

5CONNECT VALVE BODY TO STOP VALVE

1. Push VALVE BODY (1) in to STOP VALVE (2) allowing the O-ring to seal the connection.

2. Thread HEX NUT (3) on to STOP VALVE (2) to secure the connection.

Note: Do not use pipe sealant or plumbing grease.

6CONNECT VALVE BODY TO VACUUM BREAKER TUBE

1. Thread HEX NUT (1) on to the bottom of

VALVE BODY (2).

Note: Ensure that the bladder on the vacuum

breaker tube makes a good connection with

the bottom of the ﬂush valve body.

Note: If using a wired version, ensure the

wires do not get pinched while securing the

ﬂush valve body.

Note: This step is only applicable if using ASA

IoT Ceramics

1. Insert WIRE COVER (1) through FLUSH VALVE

BOTTOM COVER (3) and SPUD COVER (4).

2. Cover the WIRE (2) with the WIRE COVER (1).

(Applicable with AC Version) Cover the AC wire

with the WIRE COVER (1) similar to WIRE (2).

Note: The Wire Cover will be loose until the

next step to secure it. Ensure that the wire

does not slip out between steps.

Note: Avoid pinching or excessively bending

the wires.

Note: If the vacuum breaker tube was cut to a

shorter length, the wire cover will also need to

be cut. Wire cover length should be from the

top of the installed spud cover to the bottom

of the valve body ﬁxation nut plus 1/8”.

Note: WIRE COVER (1) is only included in ASA

IoT Ceramics Package.

7INSTALL WIRE COVER: APPLICABLE WITH ASA IOT CERAMICS

8SECURE FLUSH VALVE BOTTOM COVER

1. Secure FLUSH VALVE BOTTOM COVER (2)

with the two SET SCREWS (1) on each side.

9a MAKE WIRED CONNECTIONS: BATTERY VERSION

Note: This step is only applicable for the battery

version.

Important: Align the polarity markings (7) on the

wire ends when making the connections.

1. Connect the SOLENOID WIRE (1) to the RED

AND BLACK WIRE (2) in the ﬂush valve head.

2. Connect BLACK AND PURPLE WIRE (5) to the

BATTERY PACK (6) within the top of the ﬂush

valve head.

3. Place the BATTERY PACK (6) within the top of

the ﬂush valve head.

Note: Do not tighten ﬂush valve head at this point.

9b MAKE HOLE FOR AC WIRE

Note: This step is only applicable for the AC version.

1. Secure FLUSH VALVE HEAD (1) on to the ﬂush

valve body.

2. Using the WIRE CHANNEL (2) as a template,

mark the drill location on the wall.

3. Make an opening in the wall at the marked

location.

IMPORTANT: The hole diameter should be no

smaller than the wire channel and no larger than

the wire channel escutcheon cover.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Idiomas:

Otros manuales de Producto de plomería de American Standard

American Standard

American Standard CCAS0262 Manual de usuario

American Standard

American Standard Jasmine 3621 Series Manual de usuario

American Standard

American Standard Two-Piece Toilets With Aquameter Fill Valve... Manual de usuario

American Standard

American Standard Loft 0660.000 Manual de usuario

American Standard

American Standard Colony Soft 4275.550 Manual de usuario

American Standard

American Standard Roxalyn 00194.225 Manual de usuario

American Standard

American Standard Trap Standards 7798.020 Manual de usuario

American Standard

American Standard ONE Diverter Valve Trim Kit M968981 Manual de usuario

American Standard

American Standard Retrospect Collection Right Heigh Elongated Toilet... Manual de usuario

American Standard

American Standard Contemporary 4803900 Manual de usuario

American Standard

American Standard Seva T480.507 Manual de usuario

American Standard

American Standard Madera FloWise 15" Height 1.28 GPF Flushometer Toilet... Manual de usuario

American Standard

American Standard 2275.409 Manual de usuario

American Standard

American Standard Cadet 2832.128 Manual de usuario

American Standard

American Standard Maybrook 0.5-1.0 GPF Washout Urinal 6581.015 Manual de usuario

American Standard

American Standard Ceramix T00050X Manual de usuario

American Standard

American Standard Right Height Elongated Toilet Triumph Cadet... Manual de usuario

American Standard

American Standard Bath/Shower Trim Kits T385.507 Manual de usuario

American Standard

American Standard DXV Percy D35105.104 Manual de usuario

American Standard

American Standard FloWise 1.28 2073.013 Manual de usuario

American Standard

American Standard Cadet 6425 Instrucciones de funcionamiento y seguridad

American Standard

American Standard CADET 3 2383 Manual de mantenimiento

American Standard

American Standard Monterrey 6500 Manual de usuario

American Standard

American Standard 283 Manual de usuario

Manuales populares de Producto de plomería de otras marcas

Weka

Weka 506.2020.00E Instrucciones de funcionamiento

Kohler

Kohler K-6228 Instrucciones de montaje

UBERHAUS DESIGN

UBERHAUS DESIGN 75175017 Manual de usuario

Uponor

Uponor Contec TS Manual de usuario

Pfister

Pfister Selia 49-SL Manual de usuario

Fortis

Fortis VITRINA 6068700 Manual de usuario

Fortis

Fortis MILANO 78211JS Manual de usuario

Kohler

Kohler K-12183 Instrucciones de montaje

Maxxus

Maxxus MX-M206-01 Manual de usuario

Moen

Moen 5922 Series Manual de usuario

Viega

Viega Prevista Pure 8512 Manual de usuario

Kohler

Kohler Centerset K-15240 Instrucciones de montaje

Viega

Viega Prevista Dry 8522.33 Manual de usuario

Sanela

Sanela Lema SLP 59RB Manual de usuario

Elkay

Elkay EDF15AC Manual de instalación

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Manual

baliv

baliv WT-140 Manual de usuario

Kohler

Kohler Mira Eco Manual de operación