Full Spectrum Laser Muse Manual de usuario

Introduction 3

Section I. Safety 4

Fire Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Setup Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Safety During Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Electrical Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Harmful Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Section Review . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Section II. Unboxing Your Muse Core 9

Unboxing Steps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Section Review . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Section III. Setting Up Your Muse 14

Locate & Remove Zip Ties . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Connect the Exhaust System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Preparing Water System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Connect the Air Compressor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Connect the Electrical Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Section Review . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Section IV. Touchscreen Interface 21

Touchscreen Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Machine Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Speed Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Section Review . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Section V. Internet Connection 25

Connect to the Internet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Connect to Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Section Review . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Section VI. Tests & Adjustments 28

Alignment Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Mirror Alignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Section Review . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Section VII. Focusing Your Laser 37

Focus Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Section Review . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Table of Contents

Section VIII. Operations 40

Creating a Design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Mouse Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Section Review . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Section IX. RetinaEngrave V3 43

Starting on RE3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Compound Shapes & Objects . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

Passes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Stopping Your Laser . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Section Review . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

Section X. Maintenance 51

Removing the Laser Tube . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

Setting Up New Tube . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

Belt Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

Lens & Air Assist Cone Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

Pass-through . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

General Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

Section Review . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

Section XI. Add-ons 60

Coolbox . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

Warranty 62

Customer Support 63

Table of Contents

Thank you for purchasing your new Muse Core. Our high quality products will provide years of service simply by

following proper usage and upkeep. With proper usage and upkeep your machine will be a key part in any design

work.

This user manual will guide you through the safety guidelines and operation of your machine. We recommend that

you familiarize yourself with this manual before using your laser engraver. Remember to be safe and have fun!

For more information and product selection, please visit www.fslaser.com

Introduction

Safety Symbols & Meanings

This icon warns of potential fire hazards and fire risks.

Warning about power surges and electrical risks.

This icon indicates potential eye damage.

Warning about glass or cutting hazards.

This icon warns of potential risks of chemical inhalation.

Important information to keep in mind when running you laser.

Laser cutting and engraving systems can present a significant fire hazard due to the extremely

high temperatures generated when the laser beam is in use.

Some material are extremely flammable, catching fire quite easily and damaging the machine and

its surroundings.

Vector cutting has been shown to have the most potential for igniting material due to its direct and steady output

of current. However any function can cause fires due to negligence.

Please read the following warnings and recommendations before using your machine. These instructions should

be followed closely at all times.

●Always keep a properly maintained and inspected 5lbs. or larger fire extinguisher on hand. We

recommend a Halogen or multipurpose dry chemical fire extinguisher.

●Always keep the area around the machine clean and free of clutter. Never stack materials near or in your

work area. Clean the surrounding area regularly to avoid dust getting into the machine.

●Never store any flammable materials in or near the machine.

●Never operate your machine unattended.

●Always use the air assist, especially while vector cutting.

●Never attempt to run a laser with the lid open.

Fire Safety

Setup Precautions

Follow all safety protocols and procedures before operating any machinery. It is the responsibility

of the operator to ensure all safety precautions are correctly followed, and that the machine is

properly assembled and in working order.

●Always inspect your machine for damage or breakage before each use. Do not operate machinery

that is damaged or defective in any way.

●Always have a clean, level, and open work space to unbox and place your laser system. Never leave

the laser system unattended during operation.

●Never modify, disassemble, or in any way alter the construction of the laser and never start up a

system that has been modified or disassembled.

●Never operate the machine with any of the panels removed.

●Always have a first-aid kit designed for the initial treatment of burns and smoke inhalation.

●Never place hands or fingers into moving parts such as cooling fans.

Section I. Safety

The output of the CO2 laser is fully contained in a Class 1 enclosure during normal operation. However, the

output beam of the Alignment Laser (visible red diode laser) is accessible to the operator during normal operation, giving

the total system an overall rating of Class 3R. Class 3R lasers have minimal safety concerns when used properly and

handled with care. No special precautions are necessary to operate the high power laser safely. However we recommend

following these Safety Guidelines:

Section I. Safety

●Never engrave or cut any unknown material. Never run a laser with the lid open.

●Never operate the machine without a properly operating ventilation system.

●Never look or stare into the visible red diode laser.

Operation Safety

The power supply is capable of releasing a current up to 20mA. This power is sent to the discharge

terminals on the laser tube itself. In order to prevent access to bare wiring your laser shipped with

silicone terminal covers. Please notify Full Spectrum Laser support and immediately cease operations

if the covers ever slips and exposes the bare wires.

Electrical Safety

Note: When performing any replacement procedures, make sure the machine is off for at least an hour.

●Do not open any of the machine’s access panels while the unit is plugged in.

●Never make or break any electrical connections to the system while the unit is turned on. Never

access any electrical areas with hands or tools. The unit should be disconnected from the power for

at least one hour.

●POWER ON/OFF is controlled by the switch at the back of the machine, with (-) being ON and (o)

being OFF.

●Never replace the installed 20 amp fuse with one of a higher rating.

●In case of a blown fuse always contact Technical Support before replacing anything.

Compliance Statement:

The standard for laser safety is the American Standard for the Safe Use of Lasers, Z136.12000. Developed by the American National Standards

Institute (ANSI) it is the basis for many federal regulations and Occupational Safety and Health Administration (OSHA) guidelines for laser and

laser system manufacturers. It contains detailed information concerning the proper installation and use of laser systems. While the ANSI

standard is not a law, its recommendations, including warning signage, training, and the designation of a laser safety officer, may be mandatory

under local regulations. It is the operator's responsibility to ensure that the installation and operation of the Full Spectrum Desktop Laser System

are performed following applicable laws. Copies of ANSI Standard Z136.12000 are available from:

LASER INSTITUTE OF AMERICA 12424 RESEARCH PARKWAY, SUITE 125 ORLANDO, FL 32826 (407) 3801553.

Material DANGER! Issues

PVC (Poly Vinyl Chloride)/Vinyl/

Pleather/Most Artiﬁcial Leather

Emits Chlorine gas fumes This material can ruin the optics as well as cause the metal of the

machine to corrode. PVC can also ruin the motor system.

Thick ( >1mm )

Polycarbonate/Lexan

Catches ﬁre Polycarbonate is used in the window of varies laser cutters

because it absorbs infrared radiation. Therefore, it cannot be cut

with laser engravers. Trying to do so will create soot that can ruin

the optics and mess up the machine.

ABS plastic Melts, Emits Cyanide

fumes

ABS tends to melt creating melted deposits in the workspace and

is subsequently a high fire risk. It can also release lethal amounts

of hydrogen cyanide.

HDPE/Milk Bottle Plastic Catches ﬁre and melts HDPE can melt creating melted deposits in the workspace and is

subsequently a high fire risk.

PolyStyrene Foam Catches ﬁre Foam can ignite quickly and spread flames rapidly.

PolyPropylene Foam Catches ﬁre Foam can ignite quickly and spread flames rapidly.

Epoxy Emits fumes Epoxy is a resin made out of carbon. Therefore, a CO2 laser can't

cut it. Attempting to do so will result in toxic fumes.

Fiberglass Emits fumes It is made of glass and epoxy. Do not attempt.(Refer to epoxy)

Coated Carbon Fiber Emits fumes Cannot be cut and will emit toxic fumes.(Refer epoxy)

Any food Toxicity Our machines are not designed to be used with food as they

possess no safe food contact surfaces. There are also risks

involved with debris in the workspace polluting any food placed in

the interior. Do not put food in or around the machine.

Material with Sticky Glue or

Adhesive Backing

Coats lens or cracks lens Items that can normally be cut become uncuttable when the

manufacturer adds a layer of peel-off glue on the bottom to

attach them to surfaces.The glue will vaporize forming a coating

on the lens that will coat, cloud, heat, and potentially crack the

lens. It can't be removed without damaging to the lens, requiring a

lens replacement.

DO NOT CUT MATERIALS THAT HAVE THIS BACKING!

HARMFUL MATERIALS:

WARNING!! TRYING TO CUT THESE ITEMS WILL VOID WARRANTY!!

CUT AT YOUR OWN RISK!

Section I. Safety

The following diagrams will help you locate all of the machines components.

Section I. Safety

Top View:

Side View:

Back View:

Side View:

Power Switch

Play/ Pause

Button

Exhaust

Water

In/out

Touchscreen

Power Switch Water

Water

Out

Air Inlet

Machine

Control

Ethernet

Port

USB Port

Rotary Port

Honeycomb Tray

Section Review:

Do’s:

●Remember to make sure your work area is nice an clean. Keep your laser system clean.

●Always keep an eye on your machine.

●Always inspect your machine for damage or breakage before each use.

●Always keep a fire extinguisher and a first-aid kit (preferably one designed for the initial

treatment of burns and smoke inhalation) on hand.

Don’ts:

●Do Not stack items on or near your work area.

●Do Not leave your machine unattended.

●Never operate the machine with any of the panels removed or without a properly operating

ventilation system.

●Never access any electrical areas with hands or tools unless the unit is disconnected from

the power for at least one hour.

●Never place hands or fingers into moving parts such as cooling fans.

Section I. Safety

Section II. Unboxing

The Muse Core has a weight of 54 lbs. To avoid the potential of injury, two people are needed to lift

and unbox the machine. Lift At Your Own Risk.

Unboxing Steps

Follow these instructions for best results:

1. Prepare Work Space: You will need an open, level work space to place your laser cutter. A sturdy table with

room for the machine ( 32.5”x 20.3”x 8.5” for the workspace) is recommended. Be sure the table is free of

clutter and can support a minimum of 200lbs (the machine itself weighs 54 lbs).

2. Place Box: Place your box on or near your table before opening it, using either a pair of scissors or a box cutter.

13.7”

36.7”

25.55”

Otros manuales para Muse

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Impresora 3D de Full Spectrum Laser

Full Spectrum Laser

Full Spectrum Laser MUSE PANDORA Manual de usuario

Manuales populares de Impresora 3D de otras marcas

Ultimaker

Ultimaker S5 Material Station Manual de usuario

EcubMaker

EcubMaker TOYDIY Manual de usuario

AnyCubic

AnyCubic Kossel Plus Manual de usuario

ReDeTec

ReDeTec ProtoCycler Manual de usuario

Kywoo3D

Kywoo3D Tycoon IDEX Manual de usuario

CraftBot

CraftBot PLUS PRO Manual de usuario

3DGence

3DGence INDUSTRY F340 Manual de usuario

HP Jet Fusion 4200 Instrucciones de funcionamiento

Rokit

Rokit AEP Series Manual de usuario

AnkerMake

AnkerMake M5 Manual de usuario

DIYElectronics

DIYElectronics PRUSA I3 Instrucciones de montaje

Ackuretta

Ackuretta FreeShape 120 Manual de usuario

LONGER

LONGER LK5Pro Manual de usuario

Stratasys

Stratasys J850 Manual de usuario

MakerBot

MakerBot Replicator Manual de usuario

Stratasys

Stratasys FDM Vantage Series Manual de usuario

ZYYX

ZYYX Pro II Manual de usuario

FLASHFORGE 3D PRINTER

FLASHFORGE 3D PRINTER Creator Guía del usuario