Fujitsu MAS3367FC Manual de usuario

C141-E198-02EN

MAS3735FC

MAS3367FC

DISK DRIVES

PRODUCT/MAINTENANCE MANUAL

C141-E198

FOR SAFE OPERATION

Handling of This Manual

This manual contains important information for using this product. Read thoroughly before using

the product. Use this product only after thoroughly reading and understanding especially the section

"Important Alert Items" in this manual. Keep this manual handy, and keep it carefully.

FUJITSU makes every effort to prevent users and bystanders from being injured or from suffering

damage to their property. Use the product according to this manual.

IMPORTANT NOTE TO USERS

READ THE ENTIRE MANUAL CAREFULLY BEFORE USING THIS PRODUCT.

INCORRECT USE OF THE PRODUCT MAY RESULT IN INJURY OR DAMAGE TO

USERS, BYSTANDERS OR PROPERTY.

While FUJITSU has sought to ensure the accuracy of all information in this manual, FUJITSU

assumes no liability to any party for any damage caused by any error or omission contained in this

manual, its updates or supplements, whether such errors or omissions result from negligence,

accident, or any other cause. In addition, FUJITSU assumes no liability with respect to the

application or use of any product or system in accordance with the descriptions or instructions

contained herein; including any liability for incidental or consequential damages arising therefrom.

FUJITSU DISCLAIMS ALL WARRANTIES REGARDING THE INFORMATION

CONTAINED HEREIN, WHETHER EXPRESSED, IMPLIED, OR STATUTORY.

FUJITSU reserves the right to make changes to any products described herein without further notice

and without obligation.

This product is designed and manufactured for use in standard applications such as office work,

personal devices and household appliances. This product is not intended for special uses (atomic

controls, aeronautic or space systems, mass transport vehicle operating controls, medical devices for

life support, or weapons firing controls) where particularly high reliability requirements exist,

where the pertinent levels of safety are not guaranteed, or where a failure or operational error could

threaten a life or cause a physical injury (hereafter referred to as "mission-critical" use). Customers

considering the use of these products for mission-critical applications must have safety-assurance

measures in place beforehand. Moreover, they are requested to consult our sales representative

before embarking on such specialized use.

The contents of this manual may be revised without prior notice.

The contents of this manual shall not be disclosed in any way or reproduced in any media without

the express written permission of Fujitsu Limited.

C141-E198

Revision History

(1/1)

Edition Date Revised section (*1)

(Added/Deleted/Altered) Details

01 2003.07.29 — —

02 2003.10.07

• Table 2.1, 2.2 and 3.2 are altered.

• Table 2.3 is altered

Capacity notation is changed.

Misdescription is corrected.

*1 Section(s) with asterisk (*) refer to the previous edition when those were deleted.

This page is intentionally left blank.

C141-E198 i

Preface

This manual describes the MAS3735FC and MAS3367FC (hereafter, MAS series),

3.5 type fixed disk drives with an embedded fibre channel controller.

This manual details the specifications and functions of the above disk drive, and gives the

requirements and procedures for installing it into a host computer system.

This manual is written for users who have a basic understanding of fixed disk drives and

their use in computer systems. The MANUAL ORGANIZATION section describes

organization and scope of this manual. The need arises, use the other manuals.

The organization of this manual, related reference manual and conventions for alert

messages follow.

Overview of Manual

This manual consists of the following seven chapters, glossary, and abbreviation:

Chapter 1 General Description

This chapter introduces the MAS series disk drives and discusses their standard features,

hardware, and system configuration.

Chapter 2 Specifications

This chapter gives detailed specifications of the MAS series disk drives and their

installation environment.

Chapter 3 Data Format

This chapter describes the data structure of the disk, the address method, and what to do

about media defects.

Chapter 4 Installation Requirements

This chapter describes the basic physical and electrical requirements for installing MAS

series disk drives.

Chapter 5 Installation

This chapter explains how to install MAS series disk drives. It includes the notice and

procedures for setting device number and operation modes, mounting the disk drive,

connecting the cables, and confirming drive operation.

Chapter 6 Diagnostics and Maintenance

This chapter describes the automatic diagnosis, and maintenance of MAS series disk drive.

This chapter also describes diagnostic methods for operation check and the basics of

troubleshooting the disk drives.

Chapter 7 Error Analysis

This chapter describes in details how collect the information for error analysis and how

analyze collected error information.

Preface

ii C141-E198

APPENDIX A Connector Signal Allocation

The appendix gives supplementary information, including the signal assignments of

interface connectors.

Conventions for Alert Messages

This manual uses the following conventions to show the alert messages. An alert message

consists of an alert signal and alert statements. The alert signal consists of an alert symbol

and a signal word or just a signal word.

The following are the alert signals and their meanings:

This indicates a hazardous situation likely to result in

serious personal injury if the user does not perform the

procedure correctly.

This indicates a hazardous situation could result in serious

personal injury if the user does not perform the procedure

correctly.

This indicates a hazardous situation could result in minor

or moderate personal injury if the user does not perform

the procedure correctly. This alert signal also indicates

that damages to the product or other property, may occur if

the user does not perform the product correctly.

This indicates information that could help the user use the

product more efficiently.

In the text, the alert signal is centered, followed below by the indented message. A wider

line space precedes and follows the alert message to show where the alert message begins

and ends. The following is an example:

Preface

C141-E198 iii

(Example)

Data loss

For MAS series, Reed Solomon codes are applied for their ECC. The

sector-data is divided into 4 interleaving sectors, and ECC is performed in

each sector where the maximum number of errors (up to 5 byte) can be

corrected. [Total maximum byte: 5 byte ×4 ( interleave) = 20 byte]

If the error of read sector keeps allowable error byte number, correction is

performed. However, if error byte exceeds its allowable number,

correction may not be performed properly.

The main alert messages in the text are also listed in the “Important Alert Items.”

CONVENTIONS USED IN THIS MANUAL

The MAS3735FC and MAS3367FC disk drives are described as "the intelligent disk drive

(IDD)", "the drive" or "the device" in this manual.

Decimal number is represented normally.

Hexadecimal number is represented as X'17B9', 17B9h or 17B9H.

Binary number is represented as "010".

Attention

Please forward any comments you may have regarding this manual.

To make this manual easier for users to understand, opinions from readers are needed.

Please write your opinions or requests on the Comment at the back of this manual and

forward it to the address described in the sheet.

This page is intentionally left blank.

C141-E198 v

Important Alert Items

Important Alert Messages

The important alert messages in this manual are as follows:

A hazardous situation could result in minor or moderate personal injury if the

user does not perform the procedure correctly. Also, damage to the product

or other property, may occur if the user does not perform the procedure

correctly.

Task Alert message Page

Mounting Installation Data loss

For MAS series, Reed Solomon codes are applied for their ECC.

The sector-data is divided into 4 interleaving sectors, and ECC is

performed in each sector where the maximum number of errors (up

to 5 byte) can be corrected. [Total maximum byte: 5 byte

(interleave) = 20 byte]

If the error of read sector keeps allowable error byte number,

correction is performed.

However, if error byte exceeds its allowable number, correction

may not be performed properly.

2-5

Hot temperature

To prevent injury, do not handle the drive until after the device has

cooled sufficiently after turning off the power. The DE and LSI

become hot during operation and remain hot immediately after

turning off the power.

5-1

Important Alert Items

vi C141-E198

Task Alert message Page

Mounting Installation Damage

1. When dismounting the drive which is mounted on the system

while power is supplied to it.

• The drive to be dismounted must be separated from the

loop. Dismounting the drive which is not separated from

the loop may cause an unexpected error.

• If the drive is not separated from the loop, issue an LPB to

the drive from the initiator in a primitive sequence of the

order set.

• It is recommended to stop the spindle motor prior to this

loop separation operation. The spindle motor can be

stopped by a START/STOP command. It takes about 30

seconds for the spindle motor to stop completely.

• Then, dismount the drive using the drive

mounting/dismounting mechanism, etc. of the system. If

the drive is dismounted while the spindle motor is running,

special care is required to avoid excessive vibration or

shock to the drive. It is recommended to stop the operation

once the SCA connector breaks off contact and wait until

the spindle motor stops (about 30 seconds) before dismount

the drive.

• When storing or transporting the drive, put it in an

antistatic bag. (Shown in Section 5.1).

5-5

2. When dismounting the drive which is mounted on the system

while power is not supplied to it.

• Do not move the drive until the drive stops completely

(about 30 seconds if the spindle motor was stopped by a

START/STOP UNIT command, and about 30 seconds after

powering-off when the power was simply turned off).

• Then, dismount the drive using the drive

mounting/dismounting mechanism, etc. of the system.

• When storing or transporting the drive, put it in an

antistatic bag. (Shown in Section 5.1).

Data loss

When the SEND DIAGNOSTIC command terminates with the

CHECK CONDITION status, the INIT must collect the error

information using the REQUEST SENSE command. The RECEIVE

DIAGNOSTIC RESULTS command cannot read out the error

information detected in the self-diagnostics.

6-4

Caution

1. To avoid injury, do not touch the mechanical assembly during

disk drive operation.

2. Do not use solvents to clean the disk drive.

6-5

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Almacenamiento de Fujitsu

Fujitsu

Fujitsu ETERNUS DX60 Manual de usuario

Fujitsu

Fujitsu MHX2300BT - Mobile 300 GB Hard Drive Manual de usuario

Fujitsu

Fujitsu ETERNUS DX S2, ETERNUS DX S3, ETERNUS DX S4, ETERNUS... Manual de usuario

Fujitsu

Fujitsu ETERNUS DX100 S3 Manual de usuario

Fujitsu

Fujitsu ETERNUS AX Series Manual de usuario

Fujitsu

Fujitsu MHV2040BH Manual de usuario

Fujitsu

Fujitsu MPC3045AH Manual de usuario

Fujitsu

Fujitsu ETERNUS DX S5 Series Guía de instalación

Fujitsu

Fujitsu ETERNUS LT140 Manual de usuario

Fujitsu

Fujitsu MAT3300NC Manual de usuario

Fujitsu

Fujitsu ETERNUS DX Disk Manual de usuario

Fujitsu

Fujitsu MBC2036RC SERIES Manual de usuario

Fujitsu

Fujitsu GP5-HDH8B Manual de usuario

Fujitsu

Fujitsu Eternus DX80 S2 Manual de usuario

Fujitsu

Fujitsu eternus af Manual de usuario

Fujitsu

Fujitsu PRIMERGY SX960 S1 Manual de usuario

Fujitsu

Fujitsu MAT3300NC/NP Product/ Manual de usuario

Fujitsu

Fujitsu MAM3184MC/MP Manual de usuario

Fujitsu

Fujitsu MAN3184 SERIES Manual de usuario

Fujitsu

Fujitsu MHU2100AT Manual de usuario

Fujitsu

Fujitsu ETERNUS LT160 Manual de usuario

Fujitsu

Fujitsu Eternus DX80 S2 Manual de usuario

Fujitsu

Fujitsu ETERNUS JX40 S2 Manual de usuario

Fujitsu

Fujitsu ETERNUS LT260 Manual de usuario

Manuales populares de Almacenamiento de otras marcas

QNAP

QNAP TS 32PXU Series Manual de usuario

LaCie

LaCie RUGGED RAID Manual de usuario

Freecom

Freecom CLS DOCK Manual de usuario

PNY

PNY Attache P-FD64MBATT3 Manual de usuario

HP StorageWorks MSL2024 Manual de usuario

OLT

OLT 6x6 Maximizer Manual de usuario

Transcend

Transcend JetFlash 160 Manual de usuario

LaCie

LaCie RUGGED MINI Manual de usuario

Thunderbolt

Thunderbolt 600 Manual de usuario

Panasonic

Panasonic LB-DH8 series Manual

Intel

Intel RAID High Availability Manual de usuario

LaCie

LaCie 12big Thunderbolt 3 Manual de usuario

Spectra Logic

Spectra Logic T-Series Spectra T50e Manual de usuario

Panasonic

Panasonic LKM-F931-1 Manual de usuario

Tabernus

Tabernus Enterprise Erase E2400 Manual de usuario

Rocstor

Rocstor COMMANDER 3F series Manual de usuario

HP P9000 Manual de usuario

Western Digital

Western Digital Ultrastar Data60 Manual de usuario