Fujitsu MAU3036NC/NP Manual de usuario

C141-E205-01EN

MAU3147NC/NP

MAU3073NC/NP

MAU3036NC/NP

DISK DRIVES

PRODUCT/MAINTENANCE MANUAL

C141-E205

FOR SAFE OPERATION

Handling of This manual

This manual contains important information for using this product. Read thoroughly before using the

product. Use this product only after thoroughly reading and understanding especially the section “Important

Alert Items” in this manual. Keep this manual handy, and keep it carefully.

FUJITSU makes every effort to prevent users and bystanders from being injured or from suffering damage

to their property. Use the product according to this manual.

IMPORTANT NOTE TO USERS

READ THE ENTIRE MANUAL CAREFULLY BEFORE USING THIS PRODUCT.

INCORRECT USE OF THE PRODUCT MAY RESULT IN INJURY OR DAMAGE

TO USERS, BYSTANDERS OR PROPERTY.

While FUJITSU has sought to ensure the accuracy of all information in this manual, FUJITSU assumes no

liability to any party for any damage caused by any error or omission contained in this manual, its updates

or supplements, whether such errors or omissions result from negligence, accident, or any other cause. In

addition, FUJITSU assumes no liability with respect to the application or use of any porduct or system in

accordance with the descriptions or instructions contained herein; including any liability for incidental or

consequential damages arising therefrom.

FUJTSU DISCLAIMS ALL WARRANTIES REGARDING THE INFORMATION CONTAINED

HEREIN, WHETHER EXPRESSED, IMPLIED, OR STATUTORY.

FUJITSU reserves the right to make changes to any products described herein without further notice and

without obligation.

This product is designed and manufactured for use in standard applications such as office work, personal

devices and household appliances. This product is not intended for special uses (atomic controls,

aeronautic or space systems, mass transport vehicle operating controls, medical devices for life support, or

weapons firing controls) where particularly high reliability requirements exist, where the pertinent levels of

safety are not guaranteed, or where a failure or operational error could threaten a life or cause a physical

injury (hereafter referred to as "mission-critical" use). Customers considering the use of these products for

mission-critical applications must have safety-assurance measures in place beforehand. Moreover, they are

requested to consult our sales representative before embarking on such specialized use.

The contents of this manual may be revised without prior notice.

The contents of this manual shall not be disclosed in any way or reproduced in any media without the

express written permission of Fujitsu Limited.

C141-E205 i

REVISION RECORD

Edition Date published Revised contents

01 July, 2004

Specification No.: C141-E205-**EN

ii C141-E205

Related Standards

Product specifications and functions described in this manual comply with the following ANSI

(*1) standards.

Document number Title

T10/1236D Rev.20

[NCITS.351:2001] SCSI Primary Commands-2 (SPC-2)

T10/996D Rev.8c

[NCITS.306:1998] SCSI-3 Block Commands (SBC)

T10/1157D Rev.20 SCSI Architecture Model-2 (SAM-2)

T10/1365D Rev.10 SCSI Parallel Interface-4 (SPI-4)

*1 ANSI = American National Standard Institute

In case of conflict between this manual and any referenced document, this manual takes

precedence.

C141-E205 iii

PREFACE

This manual describes the MAU3147NC/NP, MAU3073NC/NP, and MAU3036NC/NP 3.5 type fixed disk

drives with an embedded SCSI controller.

This manual details the specifications and functions of the above disk drive, and gives the requirements and

procedures for installing it into a host computer system.

This manual is written for users who have a basic understanding of fixed disk drives and their use in

computer systems. The MANUAL ORGANIZATION section describes organization and scope of this

manual. The need arises, use the other manuals.

OVERVIEW OF MANUAL

This manual consists of the following seven chapters and two appendixes:

CHAPTER 1 GENERAL DESCRIPTION

This chapter introduces the disk drives and discusses their standard features, hardware, and system

configuration.

CHAPTER 2 SPECIFICATIONS

This chapter gives detailed specifications of the disk drives and their installation environment.

CHAPTER 3 DATA FORMAT

This chapter describes the data structure of the disk, the address method, and what to do about media

defects.

CHAPTER 4 INSTALLATION REQUIREMENTS

This chapter describes the basic physical and electrical requirements for installing the disk drives.

CHAPTER 5 INSTALLATION

This chapter explains how to install the disk drives. It includes the notice and procedures for setting device

number and operation modes, mounting the disk drive, connecting the cables, and confirming drive

operation.

CHAPTER 6 DIAGNOSIS AND MAINTENANCE

This chapter describes the automatic diagnosis, and maintenance of the disk drive. This chapter also

describes diagnostic methods for operation check and the basics of troubleshooting the disk drives.

CHAPTER 7 ERROR ANALYSIS

This chapter describes in details how collect the information for error analysis and how analyze collected

error information.

APPENDIX A TO B

The appendixes give supplementary information, including a list of setting items and the signal assignments

of interface connector.

iv C141-E205

CONVENTIONS FOR ALERT MESSAGES

This manual uses the following conventions for alerts to prevent physical or property damages to users or

by standards.

CAUTION

This indicates that either minor or moderate

personal injury may occur if the user does not

perform the procedure correctly.

NOTICE

This indicates that inconvenience to the user

such as damages to the product, equipment, data,

and/or other property may occur if the user does

not pay attention or perform the procedure

correctly.

IMPORTANT

This indicates information that the helps the user

use the product more effectively.

CONVENTIONS USED IN THIS MANUAL

The MAU3147NC/NP, MAU3073NC/NP, and MAU3036NC/NP disk drives are described as "the

intelligent disk drive (IDD)", "the drive" or "the device" in this manual.

Decimal number is represented normally.

Hexadecimal number is represented as X'17B9', 17B9h or 17B9H.

Binary number is represented as "010".

ATTENTION

Please forward any comments you may have regarding this manual.

To make this manual easier for users to understand, opinions from readers are needed. Please write your

opinions or requests on the Comment at the back of this manual and forward it to the address described in

the sheet.

C141-E205 v

Important Alert Items

Important Alert Messages

The important alert messages in this manual are as follows:

A hazardous situation could result in minor or moderate personal injury if the

user does not perform the procedure correctly. This alert signal also indicates

that damages to the product or other property may occur if the user does not

perform the procedure correctly.

Task Alert message Page

Mounting Installation Data loss

The drive adopts Reed-Solomon code for ECC.

The sector-data is divided into 3 interleaving sectors, and ECC is

performed in each sector where the maximum number of errors

(up to 9 byte) can be corrected. [Total maximum byte: 9 byte

( interleave) = 27 byte]

If the error of read sector keeps allowable error byte number,

correction is performed.

However, if error byte exceeds its allowable number, correction

may not be performed properly.

2-5

Damage

Seals on the DE prevent the DE inside from the particle. Do not

damage or peel off labels.

4-4

Hot temperature

To prevent injury, do not handle the drive until after the device has

cooled sufficiently after turning off the power. The DE and LSI

become hot during operation and remain hot immediately after

turning off the power.

5-1

Data loss

1. The user must not change the setting of terminals not described

in this section. Do not change setting status set at factory

shipment.

2. Do not change the setting of terminals except following setting

pins during the power is turned on.

• Write protect: Pin pair 9/10 of the CN2 setting terminal

(NP model only)

3. To short the setting terminal, use the short plug attached when

the device is shipped from the factory.

5-5

Damage

1. Make sure that system power is off before connecting or

disconnecting cables.

2. Do not connect or disconnect cables when power is on.(except

NC model)

5-12

vi C141-E205

Task Alert message Page

Damage

1. Be careful of the insertion orientation of the SCSI connectors.

With the system in which terminating resistor power is supplied

via the SCSI cable, if the power is turned on, the overcurrent

protection fuse of the terminating resistor power supplier may

be blown or the cable may be burnt if overcurrent protection is

not provided.

When the recommended parts listed in Table 4.2 are used,

inserting the cables in the wrong direction can be prevented.

2. To connect SCSI devices, be careful of the connection position

of the cable. Check that the SCSI device with the terminating

resistor is the last device connected to the cable.

5-12

Data loss

When the SEND DIAGNOSTIC command terminates with the

CHECK CONDITION status, the INIT must collect the error

information using the REQUEST SENSE command. The RECEIVE

DIAGNOSTIC RESULTS command cannot read out the error

information detected in the self-diagnostics.

6-4

Mounting Installation

Caution

1. To avoid shocks, turn off the power before connecting or

disconnecting a cable, connector, or plug.

2. To avoid injury, do not touch the mechanical assembly during

disk drive operation.

3. Do not use solvents to clean the disk drive.

Caution

1. Always ground yourself with a wrist strap connected to ground

before handling. ESD (Electrostatics Discharge) may cause

the damage to the device.

2. To prevent electrical damage to the disk drive, turn the power

off before connecting or disconnecting a cable, connector, or

plug.

3. Do not remove a PCA. This operation is required to prevent

unexpected or unpredictable operation.

4. Do not use a conductive cleaner to clean a disk drive assembly.

5. Ribbon cables are marked with a colored line. Connect the

ribbon cable to a cable connector with the colored wire

connected to pin 1.

6-5

6-6

Damage

Never open the disk enclosure in the field. Opening the disk

enclosure may cause an irreparable fault.

Data loss

Save data stored on the disk drive before requesting repair. Fujitsu

does not assume responsibility if data is destroyed during servicing

or repair.

6-6

6-7

C141-E205 vii

MANUAL ORGANIZATION

PRODUCT/

MAINTENANCE

MANUAL

(This manual)

1. General Description

2. Specifications

3. Data Format

4. Installation Requirements

5. Installation

6. Diagnostics and Maintenance

7. Error Analysis

SCSI Physical

Interface

Specifications

1. SCSI Bus

2. SCSI Message

3. SCSI Bus Error Recovery Processing

SCSI Logical

Interface

Specifications

1. Command Processing

2. Data Buffer Management

3. Command Specification

4. Sense Data and error Recovery Procedure

5. Disk Medium Management

This page is intentionally left blank.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Almacenamiento de Fujitsu

Fujitsu

Fujitsu ETERNUS DX60 S4 Manual de usuario

Fujitsu

Fujitsu MAS3184NC/NP Manual de usuario

Fujitsu

Fujitsu ETERNUS CS800 S6 Manual de usuario

Fujitsu

Fujitsu PRIMERGY LTO3 Manual de usuario

Fujitsu

Fujitsu DynaMO 1300 Manual de usuario

Fujitsu

Fujitsu MAF3364LC - Enterprise 36.4 GB Hard Drive Manual de usuario

Fujitsu

Fujitsu teamserver Series Manual de usuario

Fujitsu

Fujitsu ETERNUS AF S3 Series Instrucciones de montaje

Fujitsu

Fujitsu ETERNUS DX100 S4 Guía

Fujitsu

Fujitsu RE25U Manual de usuario

Fujitsu

Fujitsu ETERNUS DX500 S4/DX600 S4 Guía

Fujitsu

Fujitsu MAV2036RC - 36.7 GB Hard Drive Manual de usuario

Fujitsu

Fujitsu ETERNUS DX S5 Series Manual de usuario

Fujitsu

Fujitsu GP5-HD9G3 Manual de usuario

Fujitsu

Fujitsu AIRSTAGE UTY-ASGXZ1 Manual de usuario

Fujitsu

Fujitsu ETERNUS2000 model 100 Manual de usuario

Fujitsu

Fujitsu MAA3182FC Series Manual de usuario

Fujitsu

Fujitsu ETERNUS DX100 S4 Instrucciones de montaje

Fujitsu

Fujitsu MHV2040BH Manual de usuario

Fujitsu

Fujitsu MHV2060AT Manual de usuario

Fujitsu

Fujitsu MPF3XXXAH Manual de usuario

Fujitsu

Fujitsu ETERNUS DX60 Guía

Fujitsu

Fujitsu MHN2100AT - Mobile 10 GB Hard Drive Manual de usuario

Fujitsu

Fujitsu MJA2500BH - Mobile 500 GB Hard Drive Manual de usuario

Manuales populares de Almacenamiento de otras marcas

QNAP

QNAP TS 32PXU Series Manual de usuario

LaCie

LaCie RUGGED RAID Manual de usuario

Freecom

Freecom CLS DOCK Manual de usuario

PNY

PNY Attache P-FD64MBATT3 Manual de usuario

HP StorageWorks MSL2024 Manual de usuario

OLT

OLT 6x6 Maximizer Manual de usuario

Transcend

Transcend JetFlash 160 Manual de usuario

LaCie

LaCie RUGGED MINI Manual de usuario

Thunderbolt

Thunderbolt 600 Manual de usuario

Panasonic

Panasonic LB-DH8 series Manual

Intel

Intel RAID High Availability Manual de usuario

LaCie

LaCie 12big Thunderbolt 3 Manual de usuario

Spectra Logic

Spectra Logic T-Series Spectra T50e Manual de usuario

Panasonic

Panasonic LKM-F931-1 Manual de usuario

Tabernus

Tabernus Enterprise Erase E2400 Manual de usuario

Rocstor

Rocstor COMMANDER 3F series Manual de usuario

HP P9000 Manual de usuario

Western Digital

Western Digital Ultrastar Data60 Manual de usuario