Fujitsu ETERNUS DX60 S3 Manual de usuario
FUJITSU Storage
ETERNUS DX
Configuration Guide -Server Connection-
(Fibre Channel) ETERNUS DX60 S3/DX100 S3/DX200 S3,
ETERNUS DX500 S3/DX600 S3,
ETERNUS DX8700 S3/DX8900 S3 Disk Storage System,
ETERNUS DX200F All Flash Array Settings
P3AM-7962-08ENZ0
This page is intentionally left blank.
Preface
This manual briefly explains the operations that need to be performed by the user in order to connect an
ETERNUS DX to a server running Solaris OS, HP-UX, AIX, Windows®, Linux, VMware ESX, PAN Manager, Citrix®
XenServer®, Oracle Linux, or Oracle VM Server for x86 via a Fibre Channel interface.
This manual should be used in conjunction with any other applicable user manuals, such as those for the
ETERNUS DX, server, OS, Fibre Channel cards, and drivers.
Refer to "FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- Notations" for the notations
used in this manual such as product trademarks and product names. For storage systems that are supported
by the OS, refer to the Server Support Matrix of the ETERNUS DX.
8th Edition
June 2015
The Contents and Structure of this Manual
This manual is composed of the following two chapters.
•"Chapter 1 Workflow" (page 6)
This chapter describes the workflow when setting up a storage system.
•"Chapter 2 Setting Up the ETERNUS DX" (page 8)
This chapter describes how to set up a storage system.
3
FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection-
Copyright 2015 FUJITSU LIMITED
P3AM-7962-08ENZ0
Table of Contents
Chapter 1 Workflow 6
Chapter 2 Setting Up the ETERNUS DX 8
2.1 Common Settings ........................................................................................................................... 8
2.1.1 Setting the To-Server Connection Type (Setting the FC Port Parameters)..............................................................8
2.1.2 Creating the Server Accessible LUN Groups (Setting the LUN Groups)...................................................................9
2.1.3 Setting the Host Responses ................................................................................................................................10
2.1.4 Setting the CA Port Groups..................................................................................................................................10
2.1.5 Registering the WWNs of the Accessing Fibre Channel Cards (Setting FC Host)...................................................10
2.1.6 Allocating LUN Groups (Setting the Host Affinity)...............................................................................................11
2.2 Specific Settings ........................................................................................................................... 11
2.2.1 Setting the CA Reset Groups................................................................................................................................11
2.2.2 Setting the Subsystem Parameters .....................................................................................................................11
2.3 Checking the WWNs ..................................................................................................................... 11
4
FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection-
Copyright 2015 FUJITSU LIMITED
P3AM-7962-08ENZ0
List of Tables
Table 2.1 FC port parameter settings (FC-AL connection) ..........................................................................................8
Table 2.2 Transfer Rate setting values (for FC-AL connection) ...................................................................................8
Table 2.3 FC port parameter settings (Fabric connection) .........................................................................................8
Table 2.4 Transfer Rate setting values (for Fabric connection) ..................................................................................9
Table 2.5 Host response settings .............................................................................................................................10
5
FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection-
Copyright 2015 FUJITSU LIMITED
P3AM-7962-08ENZ0
Chapter 1
Workflow
This manual is used when performing the setup procedures described in the "Setting Up the ETERNUS DX"
section of the "FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (Fibre Channel)" for
each OS.
Required Documents
•"FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (Fibre Channel) Fibre Channel
Switch Settings"
•"Fabric OS Administrator's Guide Supporting Fabric OS"
•"FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (Fibre Channel) for Oracle Solaris"
•"ETERNUS Web GUI User's Guide"
Workflow
Setting the FC Port Parameters
Set the to-server connection type.
•"2.1.1 Setting the To-Server Connection Type (Setting the FC Port Parameters)" (page 8)
Setting the LUN Groups
Set the server accessible LUN groups.
•"2.1.2 Creating the Server Accessible LUN Groups (Setting the LUN Groups)" (page 9)
Setting the Host Responses
Set the host responses to match the connection configuration.
•"2.1.3 Setting the Host Responses" (page 10)
6
FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection-
Copyright 2015 FUJITSU LIMITED
P3AM-7962-08ENZ0
Setting the CA Port Groups
Create a group of ports for each CA type.
•"2.1.4 Setting the CA Port Groups" (page 10)
Setting the FC Host
Register the WWNs of the accessing Fibre Channel cards.
•"2.1.5 Registering the WWNs of the Accessing Fibre Channel Cards (Setting FC Host)" (page 10)
Setting the Host Affinity
Define the relationship between the FC host, the CA port group, and the LUN group.
•"2.1.6 Allocating LUN Groups (Setting the Host Affinity)" (page 11)
Setting the Specific Parameters
Set the required parameters according to the OS and the connection configuration.
•"2.2 Specific Settings" (page 11)
Checking the WWNs
Check information that is necessary for connecting to the server.
•"2.3 Checking the WWNs" (page 11)
After completing all the required procedures in this manual, follow the procedures in "FUJITSU Storage
ETERNUS DX Configuration Guide -Server Connection- (Fibre Channel)" for each OS.
Chapter 1 Workflow
7
FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection-
Copyright 2015 FUJITSU LIMITED
P3AM-7962-08ENZ0
Chapter 2
Setting Up the ETERNUS DX
2.1 Common Settings
This section explains the settings required for all server OSs, regardless of the connection configuration.
See the "ETERNUS Web GUI User's Guide" for details of how to set up and operate ETERNUS Web GUI.
2.1.1 Setting the To-Server Connection Type (Setting the FC Port Parameters)
For each connection configuration, set the indicated items only. All other parameters should be left on their
default values.
•Specify "Fabric connection" for connections to the Fibre Channel switches.
•Specify "FC-AL connection" for direct connections to the Fibre Channel cards. Specify "Fabric connection" for
direct connections to 16Gbit/s Fibre Channel cards (maximum transfer rate) with a transfer rate of 16Gbit/s.
Table 2.1 FC port parameter settings (FC-AL connection)
Parameter Solaris OS
HP-UX, AIX, Windows®, Linux, VMware
ESX, PAN Manager, Citrix XenServer,
Oracle Linux, Oracle VM Server for x86
Connection FC-AL
Set Loop ID Manual
Loop ID Values from 0x10 upwards
(Except 0x7D)
0x00
Transfer Rate See the table below (*1)
Frame Size 2048
Reset Scope I_T_L
Release Reservation if Chip is Reset Disable
*1: Set the appropriate value from the following table. Do not use [Auto-negotiation].
Table 2.2 Transfer Rate setting values (for FC-AL connection)
Fibre Channel card maximum speed Transfer rate setting value
16Gbit/s CA 8Gbit/s CA
16Gbit/s — 8Gbit/s
8Gbit/s 8Gbit/s 8Gbit/s
4Gbit/s 4Gbit/s 4Gbit/s
Table 2.3 FC port parameter settings (Fabric connection)
Parameter Setting value
Connection Fabric
8
FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection-
Copyright 2015 FUJITSU LIMITED
P3AM-7962-08ENZ0
Parameter Setting value
Transfer Rate See the table below (*1)
Frame Size 2048
Reset Scope I_T_L
Release Reservation if Chip is Reset Disable
*1: Set the appropriate value from the following table.
Table 2.4 Transfer Rate setting values (for Fabric connection)
Fibre Channel switch maximum
speed
Transfer rate setting value
16Gbit/s CA 8Gbit/s CA
16Gbit/s 16Gbit/s (*1) 8Gbit/s
8Gbit/s 8Gbit/s 8Gbit/s
4Gbit/s 4Gbit/s 4Gbit/s
*1: Specify "Auto Negotiation" for direct connections to 16Gbit/s Brocade Fibre Channel cards.
Make sure to prepare and set up Fibre Channel switches for Fibre Channel connections. For setting details,
refer to "FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (Fibre Channel) Fibre Chan-
nel Switch Settings" or "Fabric OS Administrator's Guide Supporting Fabric OS".
2.1.2 Creating the Server Accessible LUN Groups (Setting the LUN Groups)
Create LUN groups for the server to access. Refer to "Connectivity Management" in "ETERNUS Web GUI User's
Guide" for details, and set the LUN groups.
Depending on the OS version, the server may not recognize the ETERNUS DX unless a LUN group is as-
signed from LUN0. In this case, assign a LUN group starting from LUN0 in ascending order.
Chapter 2 Setting Up the ETERNUS DX
2.1 Common Settings
9
FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection-
Copyright 2015 FUJITSU LIMITED
P3AM-7962-08ENZ0
2.1.3 Setting the Host Responses
The host response parameters for the ETERNUS DX must be set to match the way the server processes the
responses to requests from the ETERNUS DX. Setting of the host response must be done before connecting
the ETERNUS DX to the server.
Set the parameters that are described below for each OS.
Retain the default values for all of the parameters that are not described below.
When setting the access path using the ETERNUS SF Storage Cruiser, the host responses for FC host will be
set to default values. Set the host response after setting the access path using the ETERNUS SF Storage
Cruiser.
Table 2.5 Host response settings
OS Conditions Host response selection
Solaris (*1) When using the OS standard Multipath Driver
(MPxIO)
Solaris MPxIO
Other cases Default
Windows®
Linux
VMware ESX
Citrix XenServer
Oracle VM Server for x86
– Default
HP-UX – HP-UX
AIX When using Symantec Storage Foundation AIX VxVM
Other cases AIX
IBM SVC – SVC
*1: An Oracle-brand Fibre Channel card driver may be used for Fujitsu Fibre Channel cards.
To confirm which driver should be used, check the "Notes" and "Fibre Channel Cards that Require an Ora-
cle-brand Driver" sections in "FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (Fi-
bre Channel) for Oracle Solaris".
2.1.4 Setting the CA Port Groups
Create new FC port groups and register the ports as members of the groups. A port group is a group of ports
that access the same LUN group (ports that are used for multipath connection to the server or for connecting
to the cluster configuring server). Configure the host affinity setting for each FC port group.
2.1.5 Registering the WWNs of the Accessing Fibre Channel Cards (Setting FC Host)
Register the WWN of each Fibre Channel card installed in the server that will access the ETERNUS DX. At the
same time, set the host response numbers registered in "2.1.3 Setting the Host Responses" (page 10) to ac-
cept these WWNs.
Registering the FC host WWNs and setting up Host Affinities as described elsewhere, allows limits to be set
on which servers are allowed to access which ETERNUS DX LUNs.
Chapter 2 Setting Up the ETERNUS DX
2.1 Common Settings
10
FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection-
Copyright 2015 FUJITSU LIMITED
P3AM-7962-08ENZ0
Otros manuales para ETERNUS DX60 S3
8
Este manual sirve para los siguientes modelos
8
Tabla de contenidos
Otros manuales de Almacenamiento de Fujitsu
Fujitsu
Fujitsu MHZ2080BJ Manual de usuario
Fujitsu
Fujitsu DynaMO 640FE Manual de usuario
Fujitsu
Fujitsu ETERNUS LT260 Manual de usuario
Fujitsu
Fujitsu ETERNUS DX Disk Manual de usuario
Fujitsu
Fujitsu RE25U300J Manual de usuario
Fujitsu
Fujitsu ETERNUS AF S3 Series Guía
Fujitsu
Fujitsu ETERNUS DX400 series Manual de usuario
Fujitsu
Fujitsu ETERNUS DX100 S3 Manual de usuario
Fujitsu
Fujitsu ETERNUS LT260 Manual de usuario
Fujitsu
Fujitsu MAP3147FC Manual de usuario
Fujitsu
Fujitsu ETERNUS DX Disk Manual de usuario
Fujitsu
Fujitsu GP5-HDH96 Manual de usuario
Fujitsu
Fujitsu ETERNUS DX60 Manual de referencia
Fujitsu
Fujitsu ETERNUS LT140 Manual de usuario
Fujitsu
Fujitsu ETERNUS DX Disk Manual de usuario
Fujitsu
Fujitsu MPG3xxxAT Manual de usuario
Fujitsu
Fujitsu Eternus DX80 S2 Guía de instalación
Fujitsu
Fujitsu ETERNUS DX60 S3 Manual de usuario
Fujitsu
Fujitsu MHW2040BH - Mobile 40 GB Hard Drive Manual de usuario
Fujitsu
Fujitsu MHG2102AT - Mobile 10 GB Hard Drive Manual de usuario
Manuales populares de Almacenamiento de otras marcas
Spectra Logic
Spectra Logic T-Series Spectra T50e Manual de usuario
Panasonic
Panasonic LKM-F931-1 Manual de usuario
Tabernus
Tabernus Enterprise Erase E2400 Manual de usuario
Rocstor
Rocstor COMMANDER 3F series Manual de usuario
HP
HP P9000 Manual de usuario
Western Digital
Western Digital Ultrastar Data60 Manual de usuario