Fujitsu BS2000 Manual de usuario

Edition June 2015

English

SE700 / SE500 / SE300

Server Unit x86

FUJITSU Server BS2000

Operating Manual

Comments…Suggestions…Corrections…

The User Documentation Department would like to know your

opinion on this manual. Your feedback helps us to optimize our

documentation to suit your individual needs.

Feel free to send us your comments by e-mail to:

manuals@ts.fujitsu.com

Certified documentation

according to DIN EN ISO 9001:2008

To ensure a consistently high quality standard and

user-friendliness, this documentation was created to

meet the regulations of a quality management system which

complies with the requirements of the standard

DIN EN ISO 9001:2008.

cognitas. Gesellschaft für Technik-Dokumentation mbH

www.cognitas.de

This manual is printed

on paper treated with

chlorine-free bleach.

Delivery subject to availability; right of technical modifications reserved.

All hardware and software names used are trademarks of their respective manufacturers.

The Xen® mark is a trademark of Citrix Systems, Inc., which manages the mark on behalf of the Xen open source

community. The Xen® mark is registered with the U.S. Patent and Trademark Office, and may also be registered in

other countries.

Novell and SUSE are registered brands of Novell, Inc. in the USA and other countries.

Linux is a registered brand of Linus Torvalds.

Windows® is a registered trademark of Microsoft Corporation.

The Linux-based basic software M2000, X2000, and HNC which is installed on the Management Unit,

Server Unit x86, and HNC contains Open Source Software. The licenses for this can be found in the LICENSES

directory on the relevant installation DVD

U41860-J-Z126-1-76

Dokuschablonen 19x24 Version 7.4de für FrameMaker V7.x vom 09.02.2010 © cognitas GmbH 2001-2010

29. Juni 2015 Stand 14:43.13 Pfad: P:\FTS-BS\Server\SE-Server\SE-Doku\1303908_BA_SU_x86\prod_e\ba_sux86.ivz

Contents

1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

2 Server Unit SU300 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

2.1 Switching the Server Unit on/off . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

2.1.1 Switching the Server Unit on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

2.1.2 Switching the Server Unit off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

2.2 Front of the Server Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

2.2.1 Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

2.2.2 Indicators on the operating panel . . . . . . . . . . . . . . . . . . . . . . . . . . 12

2.2.3 Indicators on the operable drives/components . . . . . . . . . . . . . . . . . . . . . 14

2.2.4 Hard disks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

2.2.5 DVD-RW drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

2.2.5.1 Components of the drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

2.2.5.2 Inserting a CD/DVD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

2.2.5.3 Removing a CD/DVD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

2.2.5.4 Removing a CD/DVD manually . . . . . . . . . . . . . . . . . . . . . . . . . . 17

2.2.5.5 Precautionary measures when handling CDs and DVDs . . . . . . . . . . . . . 18

2.3 Rear of the Server Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

3 What to do if ... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

3.1 Performing a system dump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

3.2 Creating diagnostic documentation . . . . . . . . . . . . . . . . . . . . . . . . . 26

Contents

U41860-J-Z126-1-76

Related publications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

U41860-J-Z126-1-76 5

Dokuschablonen 19x24 Version 7.4us für FrameMaker V7.x vom 09.02.2010 © cognitas GmbH 2001-2010

29. June 2015 Stand 14:43.13 Pfad: P:\FTS-BS\Server\SE-Server\SE-Doku\1303908_BA_SU_x86\prod_e\ba_sux86.k01

1 Introduction

The FUJITSU Server BS2000 SE Series unites the existing server lines S servers and SQ

servers in the server line SE servers.

Depending on requirements, the SE server contains all the system components needed for

operation as an overall application:

– /390-based BS2000 Server Unit

– x86-based Server Units with BS2000, Linux or Windows guest systems

– x86-based Application Units for operation under Linux, Windows or VMware

– Shareable tape and disk periphery

– A high-speed, server-internal infrastructure to connect the components with each other

and with the customer LAN or SAN.

The SE700 / SE500 / SE300 Operating Manual, which consists of a number of modules,

describes the features and hardware components of the FUJITSU Server BS2000 of the

SE Series. Users should read the operating manuals carefully in order to obtain optimal

performance from the SE server.

This manual describes the hardware component Server Unit x86 and complements the

Basic Operating Manual [1]. You will find a comprehensive introductory chapter in the Basic

Operating Manual . The chapters "Important notes" chapter on SE server operation and

"Environmental protection and service" are contained only in the Basic Operating Manual .

6 U41860-J-Z126-1-76

U41860-J-Z126-1-76 7

Dokuschablonen 19x24 Version 7.4us für FrameMaker V7.x vom 09.02.2010 © cognitas GmbH 2001-2010

29. June 2015 Stand 14:43.13 Pfad: P:\FTS-BS\Server\SE-Server\SE-Doku\1303908_BA_SU_x86\prod_e\ba_sux86.k03

2 Server Unit SU300

This section describes the Server Unit SU300. SE300 is equipped with an SU300 as the

first Server Unit. SE300, SE500 and SE700 can optionally be equipped with one or two

additional Server Units SU300.

iComponents and ports which are not used are not described below.

In the SU300 the base system X2000 enables BS2000 to execute (in Native mode or on

BS2000 VMs). Optionally X2000 enables Linux/Windows systems to operate in parallel on

XenVMs.

A SU300 occupies four height units (HUs) in the rack.

Features

– 16 models are available with up to 16 BS2000 processors. Capacity on Demand

permits temporary processor attachment.

– Depending on the model, the size of the main memory (for BS2000 and for the base

system X2000) is 32 to 64 GB in the basic configuration. All models can be enhanced

to 1504 GB.

– For the input/output system the Server Unit contains two 2.5'' SATA hard disks, each

with a capacity of 600 GB in size in the basic configuration, which are mirrored.

– The Server Unit contains a DVD-RW drive.

– Fibre Channels operating at 8 or 16 Gbps are available for connecting peripherals.

– At least one 4-port LAN card is connected on the Server Unit. The first two ports are

used for the connection to the Net Unit, and the other two can, if required, be used for

BS2000 applications. Optionally LAN controllers operating at 10 Gbps can also be

used.

– Each Server Unit is equipped with 4 power supply units. 2 + 2 redundancy in 2 phases

is thus guaranteed. If one phase fails completely, the Server Unit will continue to

operate.

Switching the Server Unit on/off Server Unit SU300

8 U41860-J-Z126-1-76

2.1 Switching the Server Unit on/off

Information on switching on and starting the SE server and on switching it off and shutting

it down is provided in the "Basic Operating Manual" [1], "Switching the server on and off".

2.1.1 Switching the Server Unit on

Before the Server Unit is switched on, the status indicator lights up green (item 5 in figure 2

on page 10).

ÊAs the administrator or a privileged operator, switch on the Server Unit using the

SE Manager (menu Hardware →Server (SE<model>, Units tab, "Switch on" function for

the Server Unit), see the “Operation and Administration” manual [5].

The power-on indicator lights up green. The Server Unit switches on, conducts a system

test and starts X2000.

If automatic IPL is configured for BS2000, the BS2000 system (Native or as a VM2000

monitor system) is also started with the configured settings.

If automatic startup is configured for XenVMs, these systems are also started.

2.1.2 Switching the Server Unit off

Before the Server Unit is switched off, the On/Off switch / status indicator lights up green,

and after the Server Unit has been switched off it no longer lights up (item 4 in figure 2 on

page 10).

ÊAs the administrator or a privileged operator, switch off the Server Unit using the

SE Manager (menu Hardware →Server (SE<model>, Units tab, "Switch off" function for

the Server Unit), see the “Operation and Administration” manual [5].

When the Server Unit is switched off, the BS2000 system is shut down properly taking into

account the remaining runtime specified.

The "Power cable connected" status indicator (item 5 in figure 2 on page 10) lights up green

when the server is switched off but connected to the power supply (power cable connected).

This status indicator does not light up in the following situations:

– The Server Unit is switched off and not connected to the power source.

– The Server Unit is switched on and operating normally.

Server Unit SU300 Front of the Server Unit

U41860-J-Z126-1-76 9

Dokuschablonen 19x24 Version 7.4us für FrameMaker V7.x vom 09.02.2010 © cognitas GmbH 2001-2010

29. June 2015 Stand 14:43.13 Pfad: P:\FTS-BS\Server\SE-Server\SE-Doku\1303908_BA_SU_x86\prod_e\ba_sux86.k03

2.2 Front of the Server Unit

Figure 1: Server Unit (front)

1 ID card (green) 5 Video port (for Customer Support only)

2 ServerView Local Service Display 6 3x USB ports (for Customer Support only)

3 Optical drive activity indicator 7 HDD indicators

4 Operating panel (for further details see figure 2

on page 10)

햲 햳 햴 햵햶햷

햸

Front of the Server Unit Server Unit SU300

10 U41860-J-Z126-1-76

Figure 2: Front - Detailed view: Operating panel

ID card

You can pull the ID card (see figure 1 on page 9) out and push it in again as far as it will go.

The ID card contains various system information, e.g. product name, serial number, MAC

addresses and DNS name.

1 ID button/ ID indicator 6 3x USB ports (for Customer Support only)

2 Reset button 7 Video port (for Customer Support only)

3 NMI button 8 HDD activity indicator

4 On/Off button / Status indicator 9 Global error indicator

5 Status indicator (power cable

connected)

10 CSS indicator

햲햳햴햵햷

햸

햹

햶

햺

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Servidor de Fujitsu

Fujitsu

Fujitsu SPARC Enterprise T5120 Manual de usuario

Fujitsu

Fujitsu PRIMERGY BX600 S3 Instrucciones de instalación

Fujitsu

Fujitsu PRIMERGY RX1330 M5 Manual de usuario

Fujitsu

Fujitsu PRIMERGY TX300 S5 Manual de usuario

Fujitsu

Fujitsu SPARC Enterprise M3000 Manual de servicio

Fujitsu

Fujitsu PRIMERGY BX900 Manual de usuario

Fujitsu

Fujitsu Primergy CX270 S2 Manual de usuario

Fujitsu

Fujitsu PRIMERGY RX100 S7 Manual de usuario

Fujitsu

Fujitsu PRIMERGY TX150 S4 Manual de usuario

Fujitsu

Fujitsu PRIMERGY ServerView Suite Manual de usuario

Fujitsu

Fujitsu FUTRO S550 Manual de usuario

Fujitsu

Fujitsu SPARC Enterprise M3000 Manual de usuario

Fujitsu

Fujitsu PRIMERGY RX2520 M5 Manual de usuario

Fujitsu

Fujitsu PRIMERGY BX620 S6 Manual del propietario

Fujitsu

Fujitsu PRIMERGY TX120 S2 Manual del propietario

Fujitsu

Fujitsu SPARC Enterprise M4000 Manual

Fujitsu

Fujitsu SPARC Enterprise T2000 Manual de servicio

Fujitsu

Fujitsu SPARC Enterprise M4000 Guía de instalación

Fujitsu

Fujitsu PRIMERGY TX120 S3 Manual de usuario

Fujitsu

Fujitsu PRIMERGY RX200 S6 Manual del propietario

Fujitsu

Fujitsu PRIMERGY RX100 S8 Manual de usuario

Fujitsu

Fujitsu Supercomputer PRIMEHPC FX700 Instrucciones de instalación

Fujitsu

Fujitsu PRIMERGY RX300 S7 Manual de usuario

Fujitsu

Fujitsu PRIMERGY TX100 S3 Manual de usuario

Manuales populares de Servidor de otras marcas

HP AlphaServer ES47 Manual de usuario

Dell

Dell PowerEdge R410 Manual de usuario

PowerNAS

PowerNAS CMA Manual de usuario

Supero

Supero FatTwin F617R3-FT Manual de usuario

MSI

MSI P1-109N-L70 Manual de usuario

Dell

Dell PowerEdge XE9640 Manual

Dell

Dell PS4100 Instrucciones de montaje

EtroVISION

EtroVISION EV3151 Manual de usuario

NEC

NEC Express5800/T110j Manual de usuario

HP ProLiant Gen9 Manual de usuario

Compaq

Compaq ProLiant 3000 Manual

Dell

Dell PowerEdge 3YPMN Manual de usuario

iRobo

iRobo IPC2U Manual de usuario

Nortel

Nortel 1000 Con?guration guide Manual de usuario

Asus

Asus AP7500 Manual de operación y mantenimiento

Avid Technology

Avid Technology AirSpeed 5000 Manual de usuario

HP Integrity rx2600 Guía de instalación

Milestone

Milestone Husky IVO 350T Manual de usuario