Fujitsu PRIMERGY RX1330 M4 Instrucciones de funcionamiento e instalación

PRIMERGY CUSTOMER INFORMATION BULLETIN

Number/Revision:

PY-CIB049-00

Issue Date:

14 April 2020

Title:

The System Tries to Power on Before iRMC is Ready

Applies to:

PRIMERGY RX1330 M4/TX1330 M4/TX1320 M4

Effective Duration:

Permanent

Problem:

When the power is connected to the PRIMERGY server, the system tries to start before

the Fujitsu Integrated Remote Management Controller (iRMC) is ready. This is indicated

by the fans speeding up to the maximum as soon as the power is connected. The iRMC

takes about two minutes to boot up, then you see the display on the screen indicating

POST and the fans slow down to normal speed.

This is not expected behavior. The iRMC should boot up first indicated by a stable

power LED. The system can then be started using the power switch (or remotely using

the iRMC interface).

Solution / Workaround:

This issue is resolved by the following procedure:

PRIMERGY CUSTOMER INFORMATION BULLETIN

1. Disconnect the power cables

2. Open the housing and locate the jumper block for UEFI Recovery (RCVR) /

Password Clear (PWD CLR)

Consult the relevant PRIMERGY Maintenance Manual from

http://manuals.ts.fujitsu.com for help to open the housing

The board schematic sticker on the inside can guide to the location of the

RCVR/PWD CLR jumper block

See an example of the jumper block in Fig.1 and a schematic on Fig.1a

below showing the neutral position (Default)

Fig. 1: Jumper in neutral position

3. Set the jumper to ‘PWD CLR’ position as shown in Fig. 2 and Fig. 2a (schematic)

4. Connect the power cables. The fans will still speed up. Wait until the monitor

displays POST after about 2 minutes by when the iRMC should be ready. A

PRIMERGY CUSTOMER INFORMATION BULLETIN

warning message will be displayed indicating the jumper is placed in a password

clear position.

5. Enter UEFI (BIOS) setup, go to ‘Save and Exit’ tab and choose ‘Save Changes

and Reset’

6. Disconnect the power cables

7. Place the jumper in the neutral position (see Fig. 1/1a)

8. Close the housing

9. Connect the power cables. The system will not start before the iRMC is ready

10.Power On the system as soon as the iRMC is ready (when the power LED stops

blinking)

Do not be concerned if the system switches off in POST and starts again

11.Enter UEFI (BIOS) setup, check and correct the necessary settings (especially

SATA operation mode if you are using the onboard SATA RAID functionality)

12.After the desired BIOS settings are set make sure to ‘Save Changes and Reset’

Revision History

REVISION

DATE

CHANGE SUMMARY

0000

14 April 2020

Initial Release

Otros manuales para PRIMERGY RX1330 M4

2

Este manual sirve para los siguientes modelos

2

Tabla de contenidos

Otros manuales de Servidor de Fujitsu

Fujitsu

Fujitsu Server PRIMERGY TX1330 M1 Manual de usuario

Fujitsu

Fujitsu PRIMERGY TX300 S3 Manual del propietario

Fujitsu

Fujitsu Primergy RX300 S2 Manual de usuario

Fujitsu

Fujitsu PRIMERGY TX200 S7 Manual de usuario

Fujitsu

Fujitsu Primergy RX300 S2 Guía

Fujitsu

Fujitsu Primergy RX300 S3 Guía

Fujitsu

Fujitsu PRIMERGY BX900 Guía rápida de usuario

Fujitsu

Fujitsu BS2000 SE Series Manual de usuario

Fujitsu

Fujitsu PRIMERGY RX600 S4 Manual de usuario

Fujitsu

Fujitsu PRIMERGY RX2530 M1 Manual de usuario

Fujitsu

Fujitsu PRIMERGY RX100 S6 Manual de usuario

Fujitsu

Fujitsu PRIMERGY RX100 S8 Manual de usuario

Fujitsu

Fujitsu Primergy TX300 S4 Manual de instrucciones

Fujitsu

Fujitsu PRIMERGY BX900 Manual de usuario

Fujitsu

Fujitsu PRIMERGY RX2520 M5 Manual de usuario

Fujitsu

Fujitsu PRIMERGY TX120 S3 Manual de usuario

Fujitsu

Fujitsu PRIMERGY TX2550 M5 Manual de usuario

Fujitsu

Fujitsu PRIMERGY RX2510 M2 Manual de usuario

Fujitsu

Fujitsu PRIMERGY TX150 S6 Manual de usuario

Fujitsu

Fujitsu PRIMERGY TX100 S2 Manual del propietario

Fujitsu

Fujitsu PRIMERGY TX140 S1 Manual de usuario

Fujitsu

Fujitsu SPARC Enterprise M8000 Manual de usuario

Fujitsu

Fujitsu PRIMERGY S60 Manual de usuario

Fujitsu

Fujitsu PRIMEQUEST 2000 Series Instrucciones de montaje

Manuales populares de Servidor de otras marcas

HP

HP AlphaServer ES47 Manual de usuario

Dell

Dell PowerEdge R410 Manual de usuario

PowerNAS

PowerNAS CMA Manual de usuario

Supero

Supero FatTwin F617R3-FT Manual de usuario

MSI

MSI P1-109N-L70 Manual de usuario

Dell

Dell PowerEdge XE9640 Manual

Dell

Dell PS4100 Instrucciones de montaje

EtroVISION

EtroVISION EV3151 Manual de usuario

NEC

NEC Express5800/T110j Manual de usuario

HP

HP ProLiant Gen9 Manual de usuario

Compaq

Compaq ProLiant 3000 Manual

Dell

Dell PowerEdge 3YPMN Manual de usuario

iRobo

iRobo IPC2U Manual de usuario

Nortel

Nortel 1000 Con?guration guide Manual de usuario

Asus

Asus AP7500 Manual de operación y mantenimiento

Avid Technology

Avid Technology AirSpeed 5000 Manual de usuario

HP

HP Integrity rx2600 Guía de instalación

Milestone

Milestone Husky IVO 350T Manual de usuario