FS IES3110-8TF Manual de usuario
L2+ MANAGED INDUSTRIAL SWITCH
L2+ MANAGED INDUSTRIELLER SWITCH
SWITCH INDUSTRIEL MANAGEABLE L2+
Quick Start Guide V1.0
Quick-Start Anleitung
Guide de Démarrage Rapide
IES3110-8TF Switch
P1 FAULT
RESET
P2
9
9
10
10
7
5
3
1 2
4
6
8
R.O.RING
1G/2.5G Link/Act 1G/2.5G
SFP
Link/Act
IES3110-8TF
Link
Act
1000
Act
Link
Introduction
Accessories
IES3110-8TF
Thank you for choosing IES3110-8TF Managed Switch. This guide is designed to familiarize you with
the layout of the switch and describes how to deploy the switch in your network.
1
EN
Mounting Bracket x2 M3 Screw x4
NOTE: IES3110-8TF switch has dust plugs delivered with it. Keep the dust plugs properly
and use them to protect idle ports.
P1 FAULT
RESET
P2
9
9
10
10
7
5
3
1 2
4
6
8
R.O.RING
1G/2.5G Link/Act 1G/2.5G
SFP
Link/Act
IES3110-8TF
Link
Act
1000
ActLink
2x 100/1000/2500BASE-X SFP Ports
1
Max. fault loading: 24V,1A
DC Input: 12-48V,1.25A max.
AC Input: 24V~,0.7A max.
23456
V1+ V1
PWR1
V2+ V2
PWR2
Fault
P1 FAULT
RESET
P2
9
9
10
10
7
5
3
1 2
4
6
8
R.O.RING
1G/2.5G Link/Act 1G/2.5G
SFP
Link/Act
IES3110-8TF
Link
Act
1000
ActLink
Front Panel Ports
Upper Panel
Hardware Overview
8x 10/100/1000BASE-T Ports
2
EN
Ports Description
10/100/1000BASE-T ports for Ethernet connection
SFP ports for 100M/1G/2.5G connection
RJ45
SFP
Grounding Point
Terminal Block Connector
Rear Panel
3
EN
Front Panel LEDs
DIN-rail Mounting Kit
P1 FAULT
RESET
P2
9
9
10
10
7
5
3
1 2
4
6
8
R.O.RING
1G/2.5G Link/Act 1G/2.5G
SFP
Link/Act
IES3110-8TF
Link
Act
1000
ActLink
SFP
RJ45
SYS
4
EN
Installation Requirements
NOTE: It is recommended to use Internet Explorer 8.0 or above to access the switch. If the
web interface of the Industrial Managed Switch is not accessible, please turn off the
anti-virus software or firewall and then try it again.
Indicates the Switch has power.
Indicates the Switch has power.
LEDs DescriptionStatus
P1
P2
Green
Light
Blink
Orange
Light
Off
Green
Green
Green
Green
Green
Indicates power failure.
Indicates that the ERPS Ring has been created successfully.
Indicates that Switch has been enabled to Ring Owner.
SYSTEM
RJ45
Fault
Ring
R.O.
Indicates the link through that port is successfully
established.
Indicates that the Switch is actively sending or receiving
data over that port.
Indicates that the port is successfully connecting to the
network at 1000Mbps.
Indicates that the port is successfully connecting to the
network at 10Mbps or 100Mbps.
LINK/ACT
1000
Green
Light
Blink
Orange
Light
Off
SFP
Indicates the link through that port is successfully
established.
Indicates that the Switch is actively sending or receiving
data over that port.
Indicates that the port is successfully connecting to the
network at 1000Mbps.
Indicates that the port is successfully connecting to the
network at 100Mbps.
LINK/ACT
1000
Before you begin the installation, make sure that you have the following:
Workstations running Windows XP/2003/Vista/7/8/10/2008, MAC OS X or later, Linux, UNIX, or
other platforms are compatible with TCP/IP protocols.
Workstations are installed with Ethernet NIC (Network Interface Card).
Ethernet Port Connection
Network cables -- Use standard network (UTP) cables with RJ45 connectors.
The above PC is installed with Web browser.
5
EN
1. Position the unit in front of the DIN-Rail and hook the mount bracket over the top of the rail.
2. Rotate the switch downward towards the rail to lock it into place. You will know it is secure when
you hear the click.
3. To remove the unit, pull down to clear the bottom of the DIN-Rail and rotate away from the rail.
Mounting the Switch
Screw on the mounting bracket on the switch with M3 screws.
DIN-Rail Mounting
Wall Mounting
Mounting the unit Releasing the unit
1
Max. fault loading: 24V,1A
DC Input: 12-48V,1.25A max.
AC Input: 24V~,0.7A max.
23456
V1+ V1
PWR1
V2+ V2
PWR2
Fault
1
Max. fault loading: 24V,1A
DC Input:12-48V,1.25A max.
AC Input:24V~,0.7A max.
23456
V1+ V1
PWR1
V2+ V2
PWR2
Fault
123456
V1+ V1
PWR1
V2
+
V2
PWR2
Fault
6
EN
The Upper Panel of the switch indicates an AC/DC inlet power socket and consists of one terminal
block connector within 6 contacts. Please follow the steps below to insert the power wire.
1. Insert positive/negative AC or DC power wires into Contacts 1 and 2 for Power 1, or Contacts 5
and 6 for Power 2.
Connecting the Power
NOTE: This product is intended to be mounted to a well-grounded mounting surface such
as a metal panel.
Grounding and wire routing help limit the effects of noise due to electromagnetic interference (EMI).
Run the ground connection from the ground screw to the grounding surface prior to connecting
devices.
Grounding the Switch
1
DC Input: 12-48V ,1.25A max.
AC Input: 24V~,0.7A max.
23456
V1+ V1
PWR1
V2+ V2
PWR2
Fault
12-48VDC,24VAC
7
EN
V1+ V1- V2+ V2-
PWR1 PWR2
123456
NOTE: The wire gauge for the terminal block should be in the range from 12 to 24 AWG.
Pin 2 / 6
Positive (+) Pin Negative (-) Pin
Pin 1 / 5
2. Tighten the wire-clamp screws for preventing the wires from loosening.
Live line/Positive
Null line/Negative
Requiring good ground connection
NameNo. Description
V1+, V2+
V1-, V2-
1
2
3
P1 FAULT
RESET
P2
9
9
10
10
7
5
3
1 2
4
6
8
R.O.RING
1G/2.5G Link/Act 1G/2.5G
SFP
Link/Act
IES3110-8TF
Link
Act
1000
Act
Link
P1 FAULT
RESET
P2
9
9
10
10
7
5
3
1 2
4
6
8
R.O.RING
1G/2.5G Link/Act 1G/2.5G
SFP
Link/Act
IES3110-8TF
Link
Act
1000
Act
Link
8
EN
1. Plug the compatible SFP transceiver into the SFP port.
2. Connect a fiber optic cable to the fiber transceiver. Then connect the other end of the cable to
another fiber device.
Connecting the SFP Ports
1. Connect an Ethernet cable to the RJ45 port of a camera, outdoor AP, computer or other network
device.
2. Connect the other end of the Ethernet cable to the RJ45 port of the switch.
Connecting the RJ45 Ports
9
EN
Step 1: Connect the computer to any RJ45 port of the switch using the network cable.
Step 2: Set the IP address of the computer to 192.168.1.x ("x" is any number from 2 to 255).
Step 3: Open a web browser, enter the default IP address of the switch 192.168.1.1, and enter the
default username and password, admin/admin.
Step 4: Click Login to display the web-based configuration page.
100M/1G/2.5G Port is not Working
1. Ensure the optical module and cable have no problem.
2. Check if the configuration at both ends of the communication device is auto or forced rate.
Connecting the Switch Remotely Unsuccessfully
1. Test network connectivity through ping.
2. If the network is reachable, try restarting the switch.
3. Check if the corresponding service is enabled.
The Port is not Working, the LED Indicator is Off
1. Ensure the switch ports are in the no shutdown state.
2. Check if the switch can read the DDM information.
3. Check if the port speed setting is correct.
4. Try looping the switch cable.
Configuring the Switch
Troubleshooting
Configuring the Switch Using the Web-based Interface
RJ45 port is not in connectivity or it is erroneous in receiving/
transmitting frames
1. Replace the twisted pair cable.
2. Check that the port configuration has the common working mode with the connected switch.
Tabla de contenidos
Idiomas:
Otros manuales de Cambiar de FS
FS
FS S3700-24T4F Manual de instrucciones
FS
FS S3700-24T4F Manual de instrucciones
FS
FS S5850-24S2C-DC Manual de usuario
FS
FS S3150-8T2FP Manual de usuario
FS
FS S5800-48F4S Manual de usuario
FS
FS NC8400 Series Manual de usuario
FS
FS N Series Manual de usuario
FS
FS S5800-48F4SR Manual de usuario
FS
FS S3900 Series Manual de usuario
FS
FS S1900-8T Manual de usuario
FS
FS S3900 Series Manual de usuario
FS
FS S5860-24XB-U Manual de usuario
FS
FS S5500-48T6SP-R Manual de usuario
FS
FS S3700-24T4F Manual de instrucciones
FS
FS S3270 Series Manual de funcionamiento
FS
FS S5800 Series Manual de usuario
FS
FS S3900 Series Manual de usuario
FS
FS S3150-8T2FP Manual de usuario
FS
FS S3700-24T4F Manual de instrucciones
FS
FS S3150-8T2FP Manual de usuario
