Front Runner JADA014 Manual de usuario
JADA014_REV_A00 © 2022 FRONT RUNNER VEHICLE OUTFITTERS
front runner
JADA014
ENG
1
Thank you for purchasing a Front Runner Hi-Lift Jack Bracket Top Mount.
Before you start, take a moment to familiarize yourself with the Fitting Instructions and the included components.
Refer to Page 2 for a list of all the components, quantities and tools required.
READ ME !
IMPORTANT WARNING!
IT IS CRITICAL THAT ALL FRONT RUNNER PRODUCTS BE PROPERLY AND SECURELY ASSEMBLED AND ATTACHED TO YOUR VEHICLE. IMPROPER ATTACHMENT COULD
RESULT IN AN AUTOMOBILE ACCIDENT, AND COULD CAUSE SERIOUS BODILY INJURY OR DEATH. YOU ARE RESPONSIBLE FOR ASSEMBLING AND SECURING ALL FRONT
RUNNER PRODUCTS TO YOUR VEHICLE, CHECKING THE ATTACHMENTS PRIOR TO USE, AND PERIODICALLY INSPECTING THE PRODUCTS FOR ADJUSTMENT, WEAR AND
DAMAGE. THEREFORE, YOU MUST READ AND UNDERSTAND ALL OF THE INSTRUCTIONS AND PRECAUTIONS SUPPLIED WITH YOUR FRONT RUNNER PRODUCT PRIOR TO
INSTALLATION OR USE. IF YOU DO NOT UNDERSTAND ALL OF THE INSTRUCTIONS AND CAUTIONS, OR IF YOU HAVE NO MECHANICAL EXPERIENCE AND ARE NOT THOROUGHLY
FAMILIAR WITH THE INSTALLATION PROCEDURES, YOU SHOULD HAVE THE PRODUCT INSTALLED BY A PROFESSIONAL INSTALLER OR OTHER QUALIFIED PERSONNEL.
NOTE: Front Runner will not be responsible for any damage caused by the failure to install the product according to these instructions.
Please call us if you have any questions about the installation of this product.
hi-lift jack bracket top mount
JADA014_REV_A00 © 2022 FRONT RUNNER VEHICLE OUTFITTERS
2
TOOLS NEEDED
FIGURE 1.1
CHECK ONLINE FOR THE LATEST FITMENT GUIDE WWW.FRONTRUNNEROUTFITTERS.COM
FIGURE 1.2
GET ORGANIZED
1
IN THE BOX
1 1 X Base plate bracket
2 1 X Clamp Bracket
3 1 X M8 x 130mm Threaded Rod
4 2 X M8 Thin Nut
5 1 X M8 Nylon Washer
6 1 X M8 Eye Nut
7 1 X M8 x 16mm Hex Head Bolt
8 3 X M8 Nyloc Nut
9 3 X M8 Plastic Nut Cap
10 2 X M10 Flat Washer
11 2 X M8 x 20mm Hex Head Bolt
12 2 X M8 x 16 x 1.6 Flat Washer
13 1 X Mounting Key
14 1 X M10 Spring Washer
15 1 X M10 Wing Nut
5mm
13
1
10
14
15
11
12
8
9
6
5
3
2
9
8
4
7
13mm Torque Wrench
2.1
2.2
2.3
In the orientation seen in Fig 2.2, please note
the position of the M8 Threaded Rod (Item 3)
and orientation of the Clamp Bracket (Item
2).
In the orientation seen in Fig 2.3, please note
the position of the M8 Threaded Rod (Item 3)
and orientation of the Clamp Bracket (Item
2).
JADA014_REV_A00 © 2022 FRONT RUNNER VEHICLE OUTFITTERS
3
ORIENTATIONS2
The Hi-Lift Jack can be mounted
length-ways anywhere on the rack as
seen in Fig 2.1. The Clamp Bracket (Item 2)
should always be mounted opening away
from you for ease of access.
3
3
2
JADA014_REV_A00 © 2022 FRONT RUNNER VEHICLE OUTFITTERS
4
FIT AND SECURE
3
3.1
3.2
3.3
13mm
Insert the two M8x20mm Hex Head Bolts
(Item 11) into the slat as shown in Fig 3.1.
Loosely assembly the Base Plate Bracket
(Item 1) using the M8 Flat Washers (Item
12) and M8 Nyloc Nuts (Item 8).
Slide an M8x16mm Hex Head Bolt (Item 7)
and a M8 Thin Nut (Item 4) into the slat as
shown in Fig 3.2. Loosley mount the Clamp
Bracket (Item 2). The M8 Nyloc Nut (Item 8)
is fastened to the M8x16mm Hex Head Bolt
(Item 7) and the Thin Nut (Item 4) recieves
the M8 Threaded Rod (Item 3), followed by
another M8 Thin Nut (Item 4).
Insert the Hi-Lift Jack (Item A) and fasten it
using the Mounting Key (Item 13), the two
M10 Flat Washers (Item 10) and the M10
Wing Nut (Item 15). Adjust the brackets so
that the M8 Threaded Rod (Item 3) aligns
with a hole in the Hi-Lift Jack (Item A).
Ensure the Hi Lift Jack (Item A) is square
and tighten the M8 Nyloc Nuts (Item 8) and
M8 Thin Nut (Item 4), securing the mounting
brackets. Place the M8 Nut Caps (Item 9)
onto the M8 Nyloc Nuts (Item 8).
11
12
8
9
1
13mm
3
2
8
4
4
7
13
10
10
14
15
A
3
Tightening Torque:
M8 : 15-20Nm / 11.06 ft lb - 14.75 ft lb
INSTALL OTHER VEHICLE AND RACK ACCESSORIES
4
Now's the time to visit your favorite Front Runner Dealer in person or online.
Be sure to tag us. We love to see our gear in action! #FrontRunnerOutfitters #BornToRoam
Share your adventures on:
FINISH
3
Congratulations! You did it. Take a step back and admire your work!
JADA014_REV_A00 © 2022 FRONT RUNNER VEHICLE OUTFITTERS
5
FIT AND SECURE
2
3.4
3.5
Close the Clamp Bracket (Item 2) and insert
a Nylon Washer (Item 5) and M8 Eye Nut
(Item 6) onto the M8 Threaded Rod (Item 3).
Ensure the Hi-Lift Jack is fitted securely and
tighten the button head bolts (Item B) as
seen in Fig 3.4.
For added security, you can use RRAC134
- Rack Accessory Lock (Item C) (sold
separately). The cable lock gets inserted
into the locking holes on the Clamp Bracket
(Item 2) as seen in Fig 3.5
13mm
B
5mm
6
5
C
Tabla de contenidos
Otros manuales de Accesorios para automóviles de Front Runner
Front Runner
Front Runner RRAC248 Manual de usuario
Front Runner
Front Runner SSDR002 Manual de usuario
Front Runner
Front Runner Pro Water Tank with Strap Manual de usuario
Front Runner
Front Runner RRAC018 Manual de usuario
Front Runner
Front Runner VACC120 Manual de usuario
Front Runner
Front Runner FAJK003 Manual de usuario
Front Runner
Front Runner RRAC201 Manual de usuario
Front Runner
Front Runner TBRA039 Manual de usuario
Front Runner
Front Runner BPTH007 Manual de usuario
Front Runner
Front Runner TOYOTA 4RUNNER Manual de usuario
Front Runner
Front Runner FSLI021 Manual de usuario
Front Runner
Front Runner FAJK007 Manual de usuario
Front Runner
Front Runner FAJK010 Manual
Front Runner
Front Runner PBTH001 Manual de usuario
Front Runner
Front Runner LATR001 Manual de usuario
Front Runner
Front Runner JCH004 Manual de usuario
Front Runner
Front Runner SHOWER ARM MKII Manual de usuario
Front Runner
Front Runner TRCA004 Manual de usuario
Front Runner
Front Runner BRONCO TBRA040 Manual de usuario
Front Runner
Front Runner SSDS201 Manual de usuario
