Froling PE1 Pellet Manual de usuario
Installation Instructions
Pellet boiler PE1 Pellet 7-35
Translation of the original German installation instructions for technicians
Read and follow the instructions and safety information!
Technical changes, typographical errors and omissions reserved!
M1441017_en | Edition 24/03/2017
Froling GesmbH | A-4710 Grieskirchen, Industriestraße 12 | www.froeling.com
Contents
1 General 4
2 Safety 5
2.1 Hazard levels of warnings 5
2.2 Qualification of assembly staff 6
2.3 Personal protective equipment for assembly staff 6
2.4 Design Information 6
2.4.1 Notes on standards 6
General standards for heating systems
6
Standards for structural and safety devices
7
Standards for heating water
7
Regulations and standards for permitted fuels
7
2.4.2 Installation and approval of the heating system 8
2.4.3 General information for installation room (boiler room) 8
2.4.4 Requirements for central heating water 9
2.4.5 Notes for using pressure maintenance systems 11
2.4.6 Use with storage tank 11
2.4.7 Chimney connection/chimney system 12
Draught limiter
12
Measuring port
12
Boiler data for planning the flue gas system
13
2.4.8 Room air-independent operation 14
2.4.9 Air supply in the installation room 15
2.4.10 Note on installing an external combustion air supply 15
2.4.11 Simultaneous operation with other air-drawing systems (room ventilation, cooker hood,
centralised dust extraction system, etc.)
17
Room air-independent appliance
18
Room air-dependent appliance
18
Requirements for operating the room air-dependent appliance simultaneously with an air-drawing
system (e.g. with a room ventilation system, centralised dust extraction system, etc.)
19
3 Technology 20
3.1 Dimensions - PE1 Pellet 7-35 20
3.2 Dimensions - PE1 Pellet 7-20 Unit 21
3.3 Connections - PE1 Pellet 7-35 22
3.4 Components and connections - PE1 Pellet 7-20 Unit 23
3.5 Technical specifications 24
3.5.1 PE1 Pellet 7-10 / PE1 Pellet 7-10 Unit 24
3.5.2 PE1 Pellet 15-20 / PE1 Pellet 15-20 Unit 26
3.5.3 PE1 Pellet 25-30 28
3.5.4 PE1 Pellet 32-35 30
3.6 External suction module 32
4 Assembly 33
4.1 Tools required 33
4.2 Transport 33
4.3 Positioning 34
4.4 Temporary storage 34
Contents
2 Froling GesmbH | A-4710 Grieskirchen, Industriestraße 12 | www.froeling.com
4.5 Setting up in the boiler room 35
4.5.1 Moving the boiler in the boiler room 35
4.5.2 Recommended clearances in the boiler room 35
4.6 Install PE1 Pellet 37
4.6.1 Remove boiler from pallet 38
4.6.2 PE1 Pellet 25-35 – Prepare the boiler for transport and setup 39
4.6.3 Aligning the boiler on the floor 40
4.6.4 Prepare for room air-independent operation 42
4.7 Install the PE1 Pellet Unit 43
4.7.1 Remove boiler from pallet 44
4.7.2 Fit the front cover 45
4.7.3 Align the boiler with the floor 46
4.7.4 Install the connection set for room air-independent operation 47
4.7.5 Expansion with electronic heating cartridge 49
4.7.6 Install boiler filling and drainage system 50
4.7.7 Expansion with pipe assembly for storage loading 51
4.7.8 Expansion with pump assembly for second heating circuit 53
4.7.9 Disassemble for easier transport to the installation site 57
4.8 Installing the discharge system 60
4.8.1 Installing the external suction module 60
4.9 Install the protective plate for the flue pipe 62
4.10 Hydraulic connection 63
4.11 Electrical Connection 64
4.11.1 Information on circulating pumps 65
5 Start-up 66
5.1 Filling the system with drinking water 66
5.2 Before commissioning / configuring the boiler 67
6 Decommissioning 68
6.1 Mothballing 68
6.2 Disassembly 68
6.3 Disposal 68
7 Appendix 69
7.1 Addresses 69
7.1.1 Address of manufacturer 69
7.1.2 Address of the installer 69
Contents
Installation Instructions PE1 Pellet 7-35 | M1441017_en 3
1 General
Thank you for choosing a quality product from Froling. The product features a state-of-
the-art design and conforms to all currently applicable standards and testing
guidelines.
Please read and observe the documentation provided and always keep it close to the
system for reference. Observing the requirements and safety information in the
documentation makes a significant contribution to safe, appropriate, environmentally
friendly and economical operation of the system.
The constant further development of our products means that there may be minor
differences from the pictures and content. If you discover any errors, please let us
know: [email protected].
Subject to technical change.
The EC Declaration of Conformity is only valid in conjunction with a delivery certificate,
which has been filled in correctly and signed as part of the commissioning process.
The original document remains at the installation site. Commissioning installers or
heating engineers are requested to return a copy of the delivery certificate together
with the guarantee card to Froling. On commissioning by FROLING Customer Service
the validity of the delivery certificate will be noted on the customer service record.
Issuing a delivery
certificate
1General
4 Froling GesmbH | A-4710 Grieskirchen, Industriestraße 12 | www.froeling.com
2 Safety
2.1 Hazard levels of warnings
This documentation uses warnings with the following hazard levels to indicate direct
hazards and important safety instructions:
DANGER
The dangerous situation is imminent and if measures are not observed it will lead
to serious injury or death. You must follow the instructions!
WARNING
The dangerous situation may occur and if measures are not observed it will lead
to serious injury or death. Work with extreme care.
CAUTION
The dangerous situation may occur and if measures are not observed it will lead
to minor injuries or damage to property.
Safety 2
Hazard levels of warnings
Installation Instructions PE1 Pellet 7-35 | M1441017_en 5
2.2 Qualification of assembly staff
CAUTION
Assembly and installation by unqualified persons:
Risk of personal injury and damage to property
During assembly and installation:
❒ Observe the instructions and information in the manuals
❒ Only allow appropriately qualified personnel to work on the system
Assembly, installation, initial startup and servicing must always be carried out by
qualified personnel:
- Heating technician / building technician
- Electrical installation technician
- Froling customer services
The assembly staff must have read and understood the instructions in the
documentation.
2.3 Personal protective equipment for assembly staff
You must ensure that staff have the protective equipment specified by accident
prevention regulations.
▪ For transportation, setup and assembly:
- suitable work wear
- protective gloves
- sturdy shoes (min. protection class S1P)
2.4 Design Information
2.4.1 Notes on standards
The system must be installed and commissioned in accordance with the local fire and
building regulations. Unless contrary to other national regulations, the latest versions
of the following standards and guidelines apply:
General standards for heating systems
EN 303-5 Boilers for solid fuels, manually and automatically fed
combustion systems, nominal heat output up to 500 kW
EN 12828 Heating systems in buildings - design of water-based heating
systems
EN 13384-1 Chimneys - Thermal and fluid dynamic calculation methods
Part 1: Chimneys serving one appliance
2Safety
Qualification of assembly staff
6 Froling GesmbH | A-4710 Grieskirchen, Industriestraße 12 | www.froeling.com
ÖNORM H 5151 Planning of central hot water heating systems with or without hot
water preparation
ÖNORM M 7510-1 Guidelines for checking central heating systems
Part 1: General requirements and one-off inspections
ÖNORM M 7510-4 Guidelines for checking central heating systems
Part 4: Simple check for heating plants for solid fuels
Standards for structural and safety devices
ÖNORM H 5170 Heating installation - Requirements for construction and safety
engineering, as well as fire prevention and environmental
protection
ÖNORM M 7137 Compressed untreated wood – Requirements for storing pellets
at the end customer’s site
TRVB H 118 Technical directives for fire protection/prevention (Austria)
Standards for heating water
ÖNORM H 5195-1 Prevention of damage by corrosion and scale formation in
closed warm water heating systems at operating temperatures
up to 100°C (Austria).
VDI 2035 Prevention of damage hot water heating systems (Germany)
SWKI BT 102-01 Water quality for heating, steam, cooling and air conditioning
systems (Switzerland)
UNI 8065 Technical standard regulating hot water preparation.
DM 26.06.2015 (Ministerial Decree specifying the minimum
requirements)
Follow the instructions of this standard and any related updates.
Regulations and standards for permitted fuels
1. BImSchV First Order of the German Federal Government for the
implementation of the Federal Law on Emission Protection
(Ordinance on Small and Medium Combustion Plants) in the
version published on 26 January 2010,
BGBl. JG 2010 Part I No. 4.
EN ISO 17225-2 Solid bio-fuel - Fuel specifications and classes
Part 2: Wood pellets for use in industrial and domestic systems
Safety 2
Design Information
Installation Instructions PE1 Pellet 7-35 | M1441017_en 7
2.4.2 Installation and approval of the heating system
The boiler should be operated in a closed heating system. The following standards
govern the installation:
EN 12828 - Heating Systems in Buildings
NOTICE! Each heating system must be officially approved.
The appropriate supervisory authority (inspection agency) must always be informed
when installing or modifying a heating system, and authorisation must be obtained
from the building authorities:
Austria: report to the construction authorities of the community or magistrate
Germany: report new installations to an approved chimney sweep / the building
authorities.
2.4.3 General information for installation room (boiler room)
Boiler room characteristics
▪ The floor must be even, clean and dry and have an adequate load-bearing
capacity.
▪ There must not be a potentially explosive atmosphere in the boiler room as the
boiler is not suitable for use in potentially explosive environments.
▪ The boiler room must be frost-free.
▪ The boiler does not provide any light, so the customer must ensure sufficient
lighting in the boiler room in accordance with national workplace design
regulations.
▪ When using the boiler above 2000 metres above sea level you should consult the
manufacturer.
▪ Danger of fire due to flammable materials.
The floor of the boiler room must not be flammable. No flammable materials
should be stored near the boiler. Flammable objects (e.g. clothing) must not be put
on the boiler to dry.
▪ Damage due to impurities in combustion air.
Do not use any solvents or cleaning agents containing chlorine and hydrogen
halides in the room where the boiler is installed (e.g. chlorination units for
swimming pools).
▪ Keep the air suction opening of the boiler free of dust.
▪ The system must be protected against the chewing or nesting of animals (e.g.
rodents etc.).
Ventilation of the boiler room
Ventilation air for the boiler room should be taken from and expelled directly outside,
and the openings and air ducts should be designed to prevent weather conditions
(foliage, snowdrifts, etc.) from obstructing the air flow.
Note on standards
2Safety
Design Information
8 Froling GesmbH | A-4710 Grieskirchen, Industriestraße 12 | www.froeling.com
Unless otherwise specified in the applicable building regulations for the boiler room,
the following standards apply to the design and dimensions of the air ducts:
ÖNORM H 5170 - Construction and fire protection requirements
TRVB H118 - Technical directives on fire protection/prevention
2.4.4 Requirements for central heating water
Unless contrary to other national regulations, the latest versions of the following
standards and guidelines apply:
Austria:
Germany:
ÖNORM H 5195
VDI 2035
Switzerland:
Italy:
SWKI BT 102-01
UNI 8065
Observe the standards and also follow the recommendations below:
❒Aim for a pH value of between 8.2 and 10.0. If the central heating water comes
into contact with aluminium, the pH value must be between 8.0 and 8.5
❒ Use prepared water which complies with the standards cited above for filling and
makeup water
❒ Avoid leaks and use a closed heating system to maintain water quality during
operation
❒ When filling with make-up water, always bleed the filling hose before connecting,
in order to prevent air from entering the system
Advantages of prepared water:
▪ Complies with the applicable standards
▪ Less of a drop in output due to reduced limescale build-up
▪ Less corrosion due to fewer aggressive substances
▪ Long-term cost savings thanks to improved energy efficiency
Limit values for filling and make-up water:
Austria Germany Switzerland
Total hardness ≤ 1.0 mmol/L ≤ 2.0 mmol/L < 0.1 mmol/L
Conductivity - < 100µS/cm < 100 µS/cm
pH value 6.0 – 8.5 6.5 – 8.5 6.0 – 8.5
Chloride < 30 mg/L < 30 mg/L < 30 mg/L
Note on standards
Safety 2
Design Information
Installation Instructions PE1 Pellet 7-35 | M1441017_en 9
Additional requirements for Switzerland:
The filling and make-up water must be demineralised (fully purified)
▪The water must not contain any ingredients that could settle and accumulate in the
system
▪ This makes the water non-electroconductive, which prevents corrosion
▪ It also removes all the neutral salts such as chloride, sulphate and nitrate which can
weaken corrosive materials in certain conditions
If some of the system water is lost, e.g. during repairs, the make-up water must also be
demineralised. It is not enough to soften the water. The heating system must be
professionally cleaned and rinsed before filling the units.
Inspection:
▪ After eight weeks, the pH value of the water must be between 8.2 and 10.0. If the central
heating water comes into contact with aluminium, the pH value must be between 8.0 and
8.5
▪ Yearly. Values must be recorded by the owner
2Safety
Design Information
10 Froling GesmbH | A-4710 Grieskirchen, Industriestraße 12 | www.froeling.com
Otros manuales para PE1 Pellet
1
Tabla de contenidos
Otros manuales de Caldera de Froling
Froling
Froling TX 250 Manual de usuario
Froling
Froling S3 Turbo 18 Manual de usuario
Froling
Froling S3 Turbo Manual de usuario
Froling
Froling Turbomat TM 320 Manual de usuario
Froling
Froling TX 250 Manual de usuario
Froling
Froling S4 Turbo Manual de usuario
Froling
Froling T4 24-150 Manual de usuario
Froling
Froling P4 Pellet 15 Manual de usuario
Froling
Froling SP Dual compact Manual de usuario
Froling
Froling S1 Turbo Manual de usuario
Froling
Froling P4 Pellet 8 - 105 Manual de usuario
Froling
Froling P4 Pellet 8-60 Manual de usuario
Froling
Froling FHG 20 Manual de usuario
Froling
Froling T4-24 Manual de usuario
Froling
Froling T4 24-150 Manual de usuario
Froling
Froling Lambdatronic P 3200 Manual de usuario
Froling
Froling TX Manual de usuario
Froling
Froling S1 Turbo Manual de usuario
Froling
Froling S3 Turbo Manual de usuario
Froling
Froling TX 200 Manual de usuario
