Follett C19999 Manual de operación
HCD1400R, HCD1400N Icemakers
Following installation, please forward this manual
to the appropriate operations person.
Operation and Service Manual
Before Serial Number C19999
Order parts online
www.follettice.com
OZ
MADEIN
THEUSA
PSIG
MODEL SERIAL NO
CORPORATION
PART NO
HZ
LOW SIDE
CHARGE
VOL
TS
Easton Pennsylv
ania
Module No.
Sto
ck Module Identific
ation Plate
Service N
o.
Product
REFRIGER
ANT
R
C
AMPS
AMPS
DESIGN PRESSURE HI
GH SIDE
MIN.BR
ANCHCIRCUITAMP
ACI
TY
MAX.
BRANCHCIR
CUITFUSESIZE
MOTOR COMPRESSOR THERMALL
Y PROTECTED
FULL L
OAD AMPS
R
SINGLE
PHASE
208264
NSF
UL L
U
00135848R04
801 Church Lane • Easton, PA 18044, USA
Toll free (800) 523-9361 • (610) 252-7301
Fax (610) 250-0696 • www.follettice.com
2
Follett equipment may be returned for credit under the following conditions:
1. The equipment is new and unused.
2. A return authorization number has been issued by customer service within 30 days after shipment.
3. Follett receives the equipment at the factory in Easton, PA within 30 days after issuance of the return authorization number.
4. The equipment must be returned in Follett packaging. If the packaging has been damaged or discarded, Follett will forward,
at the customer’s expense, new packaging.
Return freight charges are the responsibility of the customer. If equipment is returned and is damaged because of
improper packaging, Follett Corporation will not be held responsible.
Credit will be issued when:
The equipment has been inspected by Follett and deemed suitable to be returned to stock.
A 15% restocking charge will be deducted from the credit. If the cost to return the product to stock exceeds 15%, the
actual cost will be deducted.
3
Welcome to Follett Corporation
Specications
Operation
Cleaning, weekly exterior care
Cleaning, semi-annual evaporator cleaning
Service
Icemaker operation
Water system
Electrical system
Normal control board operation
Test points
Time delay and self-ushing jumpers
Error faults
Hard errors
Soft errors
Relay output indication
Compressor/refrigerant solenoid output
Wiring diagram, evaporator unit
Wiring diagram, condenser unit
Gearmotor data
Mechanical system
Evaporator disassembly
Evaporator reassembly
Refrigeration system
Condenser unit operation
Refrigerant pressure data
Refrigerant charges
Refrigeration system diagram
Refrigerant replacement requirements
Evacuation
Ambients (evaporator unit)
Ice capacity test
Bin full detection system
Troubleshooting
Replacement parts
Table of contents
4
5
7
7
7
12
12
13
14
14
15
15
15
15
15
16
16
17
18
18
19
19
21
24
24
24
24
25
26
26
26
26
27
28
30
4
Welcome to Follett
Follett equipment enjoys a well-deserved reputation for excellent performance, long-term reliability and
outstanding after-the-sale support. To ensure that this equipment delivers the same degree of service, we ask
that you review the installation manual (provided as a separate document) before beginning to install the unit.
Our instructions are designed to help you achieve a trouble-free installation. Should you have any questions or
require technical help at any time, please call our technical service group at (800) 523-9361 or (610) 252-7301.
Before you begin
After uncrating and removing all packing material, inspect the equipment for concealed shipping damage. If damage
is found, notify the shipper immediately and contact Follett Corporation so that we can help in the ling of a claim,
if necessary.
Check your paperwork to determine which model you have. Follett model numbers are designed to provide information
about the type and capacity of Follett equipment. Following is an explanation of the different model numbers in the
1400 series.
Horizon Series Icemaker Model Number Configurations
A Air-cooled, self-contained
W Water-cooled, self-contained
R Air-cooled, remote condensing unit
N Air-cooled, no condensing unit for
connection to parallel rack system
RVSD 1400HC
HC Horizon
Chewblet®
D Low side 115/60/1
Condenser 208-230/60/1
(remote condensing only)
C 208-230/60/1
(self-contained only)
E 230/50/1
(self-contained only)
Icemaker
Model Series Voltage
Capacity
Model Series Condenser
V Vision™
H Harmony™
B Ice storage
bin
J Drop-in
1000 up to
1036 lbs
(471kg)
1400 up to
1450 lbs
(658kg)
S Satellite-fill™
T Top-mount
Application Configuration
Chewblet is a registered trademark of Follett Corporation, registered in the US.
CAUTION
• Moving parts. Do not operate with front cover removed.
• Hot parts. Do not operate with cover removed.
• To reduce risk of shock, disconnect power before servicing.
• Most ice machine cleaners contain citric or phosphoric acid, which can cause skin irritation. Read caution
label on product and follow instructions carefully.
• Ice is slippery. Maintain counters and oors around dispenser in a clean and ice-free condition.
• Ice is food. Follow recommended cleaning instructions to maintain cleanliness of delivered ice.
5
Specications
Electrical
Separate circuit and equipment ground required.
Evaporator unit
Standard electrical – 115/60/1
Maximum fuse – 15 amps
Amperage – 6 amps
Condenser unit
Standard electrical – 220V, 60Hz, 1 phase
Maximum fuse – 40 amps
Amperage – 21.4 amps
Evaporator plumbing
3/8" OD push-in water inlet
3/4" MPT
Notes: 3/4" vented drain line must slope a minimum of 1/4" per foot (6mm per 30.4cm run).
Drain to be hard piped and insulated.
Water shut-off recommended within 10 feet (3m).
Follett recommends installation of Follett water lter system (part# 00130286) in icemaker
inlet water line.
Ambient
Evaporator unit
Air temperature 100˚F/38˚C max. 50˚F/10˚C min.
Water temperature 90˚F/32˚C max. 45˚F/7˚C min.
Water pressure 70 psi max. (483 kPa) 10 psi min. (69 kPa)
Condenser unit
Air temperature 120˚F/49˚C max. – 20˚F/-29˚C min.
Refrigeration
3/8" liquid line
5/8" suction line
Note: Rack system installations require a reserve capacity of 10,000 BTU/hr at
2˚F (– 17˚C) evaporator temperature.
Evaporator pressure regulator (not supplied) is required.
Weight Ice production
Evaporator unit
190 lbs (88kg)
Condenser unit
385 lbs (175kg)
F
C
50
10
60
16
70
21
80
27
90
32
60
16
1231
559
1182
537
1146
520
1110
504
1074
488
70
21
1206
548
1157
525
1121
509
1085
493
1049
476
80
27
1163
528
1127
512
1091
495
1055
479
1019
463
90
32
1128
512
1088
494
1048
476
1008
458
968
440
100
38
1098
499
1055
479
1012
460
969
440
926
421
lbs
kg
lbs
kg
lbs
kg
lbs
kg
lbs
kg
Inlet Water Temperature F/C
Ambient Air Temperature F/C
Icemaker capacity/24 hrs.
6
Dimensions and clearances
Entire front of icemaker must be clear of obstructions/connections to allow removal.
1" (26mm) clearance above icemaker for service.
1" (26mm) minimum clearance on sides.
Condensing Unit
Front View
Condensing Unit
Side View
Condensing Unit
Back View
40.7"
(1034mm)
31.25"
(794mm)
5/8" OD low pressure line (suction line)
Power connections
3/8" OD high pressure line (liquid line)
26.54"
(675mm)
Front View Side View Back View
3/8" OD push-in
water inlet
5/8" suction line
3/8" liquid line
Ice transport tube connection
19.3" (491mm)
2.5" (64mm)
15.69" (399mm)
2.53"
(65mm)
6.95"
(177mm)
14.47"
(368mm)
2.87
(73mm)
1.81
(46mm)
3/4" MPT drain
PSIG
THEUSA
MADE IN
OZ
PHASE
SINGLE
LOW SIDE
CHARGE
PART NO
RR
HZ
Easton Pennsylvania
208264
AMPS
AMPS
VOLTS
SERIALNO
CORPORATION
MODEL
Service No.
Product
Module No.
REFRIGERANT
FULL LOA D AMPS
Stock Module IdentificationPlate
DESIGNPRESSURE HIGHSIDE
MAX.BRANCHCIRCUIT FUSESIZE
MIN.BRANCHCIRCUITAMPACITY
MOTORCOMPRESSORTHERMALLY PROTECTED
C
NSF
ULUL
21.05" (535mm)
23.50"
(597mm)
21.28" (541mm) Air exhaust
both sides
23.77" (604mm)
G
L2
L1
NEMA 5-15
right angle
7
Operation
Cleaning and preventive maintenance (all models)
Note: Do not use bleach to sanitize or clean the icemaker.
Preventive maintenance
Periodic cleaning of Follett’s icemaker system is required to ensure peak performance and delivery of clean,
sanitary ice. The recommended cleaning procedures that follow should be performed at least as frequently as
recommended, and more often if environmental conditions dictate.
Cleaning of the condenser can usually be performed by facility personnel. Cleaning of the icemaker system,
in most cases, should be performed by your facility’s maintenance staff or a Follett authorized service agent.
Regardless of who performs the cleaning, it is the operator’s responsibility to see that this cleaning is performed
according to the schedule below. Service problems resulting from lack of preventive maintenance will not be
covered under the Follett warranty.
Weekly exterior care
The exterior may be cleaned with a stainless cleaner such as 3M Stainless Steel Cleaner & Polish or equivalent.
Monthly condenser cleaning (air-cooled icemaker only)
1. Use a vacuum cleaner or stiff brush to carefully clean condenser coils of air-cooled icemakers to ensure
optimal performance.
2. When reinstalling counter panels in front of remote icemakers, be sure that ventilation louvers line up with
condenser air duct.
Semi-annual evaporator cleaning (every 6 months)
WARNING
• Wear rubber gloves and safety goggles (and/or face shield) when handling ice machine cleaner or sanitizer.
CAUTION
• Use only Follett approved SafeCLEAN™ Cleaner (part #00132001) and NU-CALGON IMS-II SANITIZER.
• Do not mix Cleaner and Sanitizer solutions together.
• DO NOT USE BLEACH.
• It is a violation of Federal law to use these solutions in a manner inconsistent with their labeling.
• Read and understand all labels printed on packaging before use.
Note: Complete procedure for cleaning an sanitizing MUST be followed. Ice must be collected for 10
minutes before putting ice machine back into service.
1. To clean – Remove cover. Press the CLEAN
button. The machine will drain. Wait for the LO
WATER light to come on (Fig. 1).
LO WATER
CLE
AN
Fig. 1
8
2. Mix 1 gallon (3.8L) 120˚F (49˚C) water and
7 ounces (198g) (one 7 ounce packet of Follett
SafeCLEAN ice machine cleaner, part#-00132001).
Locate cleaning cup. Fill until HI WATER light
comes on (Fig. 2).
Note: Do not use bleach to sanitize or clean the
icemaker.
3. Replace cover on cleaning cup. Wait until machine
restarts. Machine will clean, then ush 3 times in
approximately 12 minutes (Fig. 3).
4. To sanitize – Press CLEAN button. The machine
will drain. Wait for LO WATER light to come on (Fig.
4).
HI WATER
Fig. 2
12
Fig. 3
LO WATER
N
A
E
L
C
Fig. 4
9
HI WATER
Fig. 5
12
Fig. 6
Fig. 7
5. Mix 1 gallon 120˚F (49˚C) water and 1.6 ounces
(48ml) NU-CALGON IMS-II SANITIZER. Fill until
HI WATER light comes on (Fig. 5).
Note: Do not use bleach to sanitize or clean the
icemaker.
6. Replace cover on cleaning cup. Wait until machine
restarts. Machine will sanitize, then ush 3 times in
approximately 12 minutes (Fig. 6).
7. To clean transport tube – Press power switch OFF
(Fig. 7).
10
Fig. 8
1
2
3
16"
(407mm)
Fig. 9
Fig. 10
8. Disconnect coupling as shown (Fig. 8).
9. Using disposable food service grade gloves,
insert dry Sani-Sponge™ (kit part# 00132068).
Next,-insert Sani-Sponge soaked in Nu-Calgon
IMS-II sanitizer solution. Push both Sani-Sponges
down ice transport tube with supplied pusher tube
(Fig. 9).
10. Remove and discard 16" (407mm) pusher tube
(Fig. 10).
Este manual sirve para los siguientes modelos
2
Tabla de contenidos
Otros manuales de Máquina de hielo de Follett
Follett
Follett Horizon Chewblet series Manual de usuario
Follett
Follett Horizon Elite HC-1810R/N Manual de operación
Follett
Follett 230V 50Hz Suplemento
Follett
Follett Horizon HME14000ABT Manual de usuario
Follett
Follett Horizon Elite Chewblet HCF1010RMS Manual de usuario
Follett
Follett HCD1000RBT Manual de usuario
Follett
Follett Horizon Elite series Manual de usuario
Follett
Follett M25578 Manual de operación
Follett
Follett Horizon Elite HMD1410N Manual de operación
Follett
Follett L82639 Manual de operación
Follett
Follett Horizon HME1000ABT Manual de usuario
Follett
Follett Horizon Elite Chewblet HCD1010RMS Manual de usuario
Follett
Follett HCC1400A Manual de operación
Follett
Follett Horizon HMD700NHT Manual de usuario
Follett
Follett Horizon Elite HCD710A Manual de usuario
Follett
Follett MCC400A Guía de configuración
Follett
Follett Horizon Elite Chewblet HCD1010RHS Manual de usuario
Follett
Follett Horizon Elite Chewblet 1010 Series Manual de usuario
Follett
Follett HCE1400A Manual de operación
Follett
Follett HCC1000A Manual de operación
