Folger Technologies 2020 Prusa i3 Manual de usuario
http://www.folgertech.com 2020 Prusa i3 | Build Guide Page: 1 / 38
FOLGER TECHNOLOGIES, LLC
2020 i3 –3D Printer Kit
BUILD GUIDE
Rev. A
Thank you for your purchase!
http://www.folgertech.com 2020 Prusa i3 | Build Guide Page: 2 / 38
We are happy to announce this as our 3rd complete 3D printer kit. The Folger Tech
2020 i3 kit combines the simplicity of an erector set with the power of a much
more expensive desktop printer. This kit includes everything you need to
assemble the 8 cubic inch print area machine (with the exception of an 8x8” glass
surface & the tools required for assembly).
Note From the Author:
This guide was made from the perspective of someone that has never built
a 3D printer. I built the printer with only the prototype as a visual reference.
Taking pictures each step of the way and making small notations I was able to
put together the following guide over the next couple weeks. Once the first draft
was completed we had one of our warehouse girls take a kit and try to assemble
it. She had zero technical experience and made notes (lots of them) on each page
as she went along. She completed her first printer and I took the notes back to
my desk to complete this guide. This is the finished product. I look forward to
your feedback and hope you enjoy building this extremely fun i3 kit!
Thanks,
Dan
Folger Technologies
Offical RepRap Forum Thread:
http://forums.reprap.org/read.php?4,512329,512329#msg-512329
Visit us on IRC:
irc.freenode.net
#folgertech
If you feel you are missing items from your kit or have suggestions for
improvements to the build guide please email us at:
We are also planning on offering 2 upgrades for this kit:
1) Extended 200x300MM bed.
2) Auto bed leveling with proximity sensor and aluminum plate.
Step 1: Un-box everything and separate like parts into areas you can grab from.
Step 2: Get out your calipers or ruler and separate screws into different
piles based on size (believe us, it makes things much easier). Step 3:
Assemble Bottom Half Of Main Frame:
http://www.folgertech.com 2020 Prusa i3 | Build Guide Page: 3 / 38
•Parts Needed: (2) 365MM 2020, (2) 375MM 2020, (4) SK8's, (1) Motor Mount, (2) 2020
corner brackets.
•Hardware Needed: (8) 2020 L Mounts w/ Set Screws, (8) 5mm T-Nuts, (4) 4mm T-Nuts,
(4) M4x8MM Pan Head Bolts, (8) M5x8MM Bolts.
1. Take the 375MM 2020 Beam and place it in front of you, we are going to attach the
corner brackets, and SK8's before continuing with the frame assembly. [Insert Picture
Here]
2. Using (2) 4MM T-Nuts & (2) 4Mx8MM Pan Head Bolts attach the 2020 corner brackets
to the center of the 375MM 2020 Beam spacing them about an inch apart. Note: this
will be adjusted later.
3. Slide (2) 5MM T-Nuts to the left of the corner brackets, and (2) 5MM T-Nuts to the right
of the corner brackets.
4. Attach the (2) SK8's to the M5 T-Nuts using the (4) M5x8MM Bolts. Note: the tension
screws for the SK8's should be facing outwards to make it easier to tighten them later.
5. Take the other 375MM 2020 Beam and place it in front of you, we are going to attach
the motor mount, and the remaining 2 SK8's.
http://www.folgertech.com 2020 Prusa i3 | Build Guide Page: 4 / 38
6. Repeat the process from step 3 to attach the remaining 2 SK8's by sliding (4) M5 TNuts
onto the top of the 2020 beam and attach the remaining (2) SK8's using (4) M5x8MM
Bolts.
7. Take the metal motor mount and attach it to the front face of the 375MM 2020 Beam in
between the SK8's using (2) M4 T-Nuts & (2) M4x8MM Pan Head Bolts. Note: this will
need to be moved left and right to adjust screws later so you can leave it loose for
now.
8. Now take (4) 2020 L Mounts & the remaining (2) 365MM 2020 Beams. Slide (2) 2020 L
Mounts back to back on the top of each of the 365MM 2020 Beams. Each one should
look like the picture below. Do not secure these in place as they will be moved later.
Note: Ignore the L Bracket in the left of the picture it shouldn't be there yet.
9. You can now use the remaining (4) 2020 L Mounts to secure the bottom frame
together. Tighten the set screws to lock them in place. Use the below pictures as
reference. Note: The motor mount is not pictured, but should be attached to the rear
2020 beam.
Step 4: Attach Y Carriage Rails & Bearings:
http://www.folgertech.com 2020 Prusa i3 | Build Guide Page: 5 / 38
•Parts Needed: (2) 395MM Chrome Rods, (3) LM8UU Bearings, Bottom Frame Assembly.
•Hardware Needed: none
1. Place the bottom frame in front of you so the motor mount is at the back of the
printer. Note: This is the front position of the printer. The motor mount is missing from
this picture but should be attached to the rear 2020 beam.
2. Slide (1) 395MM Chrome Rod through the front right SK8 about half way through.
3. Carefully slide (2) LM8UU Bearings onto the Chrome Rod & finish pushing the Chrome
Rod through to the other SK8. Be careful not to hit the corner of the rod on the inside
of the LM8UU which can cause bearings to fall out.
4. Similar to step 3 slide the remaining (1) 395MM Chrome rod into the left side SK8 and
slide (1) LM8UU Bearing onto the rod.
http://www.folgertech.com 2020 Prusa i3 | Build Guide Page: 6 / 38
5. Be Sure to tighten the tension screws on the (4) SK8's to secure the chrome rod's in
place.
Step 5: Attach & Assemble The Upper Frame
Parts Needed: (2) 295MM 2020 Beam, (1)375MM 2020 Beam, Bottom Frame Assembly.
Hardware Needed: (3) 2020 L Mounts w/ Set Screws.
1. Take the (2)295MM 2020 Beams and attach them vertically to the left and right side of
the Bottom Frame Assembly using the (2) 2020 L Mount's on each side that we placed
in step 3:8. Before securing them make sure the back side of the beam is 90MM from
the back of the printer.
2. Before attaching the top we are going to attach (1) 2020 L Mount to the outside of the
left most vertical 295MM 2020 Beam for the Spool Holder which we will attach later.
3. Now attach the remaining (1) 375MM 2020 Beam to the top of the (2) vertical 295MM
2020 Beams using (2) 2020 L Mounts w/ Set Screws to secure them in place.
http://www.folgertech.com 2020 Prusa i3 | Build Guide Page: 7 / 38
Step 6: Assemble The Aluminum Heat Bed Plate
•Parts Needed: (1) Aluminum Bed Plate, (3) Printed Bearing Mounts, (1) Printed Belt
Carriage.
•Hardware Needed: (6) Small Zip Ties, (6) M3x20MM Bolts, (2) M3x12MM Bolts (8) M3
Nylock Nuts.
1. Remove the blue protective layer off both sides of the Aluminum Bed Mount.
2. Take the (3) Printed Bearing Mounts and attach (2) Small Zip Ties to each by sliding
the Zip Tie through the guide holes (as pictured).
3. Using the (6) M3x20MM Bolts & (6) M3 Nylock Nuts, attach the Printed Bearing Holders
to the Aluminum Bed Plate. Use the (2) M3x12MM Bolts and (2) M3 Nylock Nuts to
attach the Printed Belt Carriage to the Aluminum Bed Mount using the pre drilled holes.
Note: the opening on the Printed Belt Carriage is facing the side with 2 bearing holders.
http://www.folgertech.com 2020 Prusa i3 | Build Guide Page: 8 / 38
4. Now we are going to attach the Aluminum Bed Mount to the bearings on the Bottom
Frame Assembly of the printer by pushing them down into the LM8UU Bearings. Line up
the Printed Bearing Holders over the LM8UU's attached to the Chromed Rod and apply
enough pressure to snap the bearings into the Printed Bearing Mounts. Note: you
should feel a small pop as it sets into the grooves.
5. Tip the frame backward and close the Small Zip Ties that you previously attached to
the Printed Bearing Holders over the LM8UU Bearings securing them in place. Note:
Once tightened you can clip the excess material from the Small Zip Ties.
Step 7: Solder The MK2B Heated Bed & Attach Thermistor
•Parts Needed: (1) MK2B Heated Bed, (1) Thermistor, (1) xM Black 16 Gauge Wire, (1)
xM Red 16 Gauge Wire.
•Special Tools Needed: Soldering Iron, Solder, Kapton Tape
1. Prepare your MK2B Heated Bed to be soldered.
http://www.folgertech.com 2020 Prusa i3 | Build Guide Page: 9 / 38
2. Apply solder to contacts #1, #2, & #3.
3. Strip the ends off and apply solder to one end of both the Black & Red 16 Gauge Wire.
4. Solder the stripped and soldered end of the Black 16 Gauge Wire to both contacts #3 &
#2. Note: This is critical, if you do not make contact with both #3 & #2 you will only be
running at 12v and will not be able to reach max bed temp.
5. Solder the stripped and soldered end of the Red 16 Gauge Wire to contact #1.
http://www.folgertech.com 2020 Prusa i3 | Build Guide Page: 10 / 38
6. Place the glass of (1) Thermistor into the small hole in the center of the heated bed.
7. Using the provided Kapton Tape, secure both the Thermistor and the Red & Black 16
Gauge wire to the bottom of the heated bed. Note: use these pictures as a guideline
but you can use more/less tape and position the wires as you see fit.
Step 8: Attach the Heated Bed to the Aluminum Bed Plate.
•Parts Needed: (1) MK2B Heated Bed Pre Wired from Step 7
•Hardware Needed: (4) Springs, (4) Thumb Screws, (4) M3x16MM Bolts
1. Feed (1) M3X8MM Bolt through each corner hole on the MK2B Heated Bed > Spring >
Aluminum Bed Plate > Secure with (1) Thumb Screw. Note: wires should be coming
out the back of the printer. Thumb screws just need to be hand tight for now and can
be adjusted later.
Tabla de contenidos
Otros manuales de Impresora 3D de Folger Technologies
