Flycam HD-3000 Manual de usuario
1
What’s In The Box
Please inspect the contents of your shipped package to ensure you have received everything that
is listed below.
Galaxy Arm Vest with HD-3000 Stabilizer (GLXY-AV-HD-3)
All rights reserved.
No part of this document may be reproduced, stored in a retrieval system, or transmied by any form or by any means,
electronic, mechanical, photo-copying, recording, or otherwise, except as may be expressly permied by the applicable copyright
statutes or in wring by the Publisher.
Ass e mb l y M a n u a l
HD-3000
Stabilizer
Galaxy Arm
Table Clamp Metal Quick
Release
Storage Bag
Galaxy Vest
2
Aach Central Post to the Base Plaorm by
means of threaded stud in center. Rotate the
Base Plaorm to properly secure with Central
post.
Loosen allen bolts at boom of Camera Plate,
align its holes with top of Central Post &
re-ghten them securing the plate to post.
Steadycam Setup
Open lever and remove Quick Release Plate
from Adapter. Then aach it with your camera
with help of screw driver. Insert your camera
setup into Adapter and ghten the lever back.
NOTE: The camera can be directly aached to Head Plate.
Remove Head plate from 3-piece Head Assembly in order to aach it to your camera. You will note a
number of mounng holes that can be used to adapt various cameras. Keep the camera in center of
Head Plate and secure it properly.
Do not over ghten this adjustment as it can break the threaded insert.
NOTE: You can also mount your camera using Quick Release Plate.
Adding Weights & Posioning for Proper Balance
Connuing assembly & balance requirements
to make your Flycam Handheld Video Stabilizer
fully funconal you will note that the base
plaorm has a provision to mount balance
weights via 2x BH bolts secured with knobs on
both sides of the post.
3
Having put your vest on, insert the hooks of
the 26’’ long straps into the appropriate
buckle. Then ghten both straps with Velcro
for a comfortable t and lock both with the
buckles.
The length of the chest plate can be adjusted
according to the height of the person by using
this adjusng screw.
Steadycam Arm & Vest Setup
Loosen the knobs & insert Arm’s male socket
into female socket of vest as shown in image.
Now, your Galaxy Steadycam Arm & Vest
assembly is ready to use.
NOTE: Properly set up and custom t, your vest should look like the provided picture. Straps are made
of through nylon and industrial strength Velcro and can be easily replaced or adjusted to suit individual
needs.
The purpose of counter weight system is to match the low end of stabilizer to weight of the camera and
accessories at the high/top end with the gimbal handle as the pivot point in between.
The heavier camera and accessories, the more weights are required to achieve proper balance. Generally
as you add weight to one side of central post, an equal amount has to be added to other side to maintain
horizontal balance.
The arm tension is adjusted for the heaviest camcorder, so when you apply the camcorder and sled on the
arm for the first time it does not stay down. Now adjust the arm for the weight of your camcorder:
Move the arm to the middle of its booming (up and down range) and let go. (If it stays where it is, you
are probably close to the right adjustment).
Keep making small adjustments until the camcorder does not rise or fall when you let go of it in the
middle of its booming range.
Arm Adjustment
4
For Interchanging the spring, Follow this video
https://bit.ly/34o0fgk
Bearing Maintenance
The Flycam GALAXY Arm contains the bearings. If aer some period of me your bearings don’t turn
smoothly as when new, you can oil it lightly with light lubricang oil. We recommend that you use a
minimum amount. Only a few drops are required, plus anything more than a lile will end up dripping
from the bearing and onto the rest of your Galaxy Arm. Be sure to keep the oil away from your Camera,
and clean up any over spill when done.
Cleaning
Do not use solvents or harsh cleaners of any kind on your Flycam Galaxy Arm & Vest. If the unit becomes
dirty, use only a cloth or sponge with water and a very mild detergent to gently rub the unit clean. Rinse
well.
Storage
If you are going to store your Flycam Galaxy Arm & Vest for a long period of me then please store the
unit up right in a dry or low to normal humidity area whenever possible.
If you are unable to nd an environment like this, then we suggest you store the unit in an airght plasc
container or bag. Standing the unit upright helps to alleviate stress on the system.
Maintenance
Posion arm
Move the camcorder to your left so the arm crosses your body.
Adjust the arc of your arm so the rig feels comfortable to you.
Keep the camcorder close to your body.
YOUR FLYCAM GALAXY STEADYCAM ARM & VEST WITH HD-3000
ALL DRESSED UP AND READY TO GO!
(SHOWN WITH OPTIONAL ACCESSORIES)
Otros manuales para HD-3000
1
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Accesorios para cámaras de Flycam
Flycam
Flycam Galaxy Stabilizer Arm & Vest Manual de usuario
Flycam
Flycam FLOWLINE 300N Manual de usuario
Flycam
Flycam FLCM-QR Manual de usuario
Flycam
Flycam FLCM-FLN-SM Manual de usuario
Flycam
Flycam 5000 Manual de usuario
Flycam
Flycam FLCM-FLN-CH Manual de usuario
Flycam
Flycam Flowline Master Manual de usuario
Flycam
Flycam buddy flcm-bdy Manual de usuario
Flycam
Flycam Yoko Steady Stabilizer Support Manual de usuario
Flycam
Flycam FLCM-FLN-MSTR-02 Manual de usuario
Flycam
Flycam Flowline B-FLCM-FLN Manual de usuario
Flycam
Flycam DSLR Camvest Manual de usuario
Flycam
Flycam FLCM-FLN-MSTR-PLA Manual de usuario
Flycam
Flycam 5000 Manual de usuario
Flycam
Flycam FLCM-BP Manual de usuario
Flycam
Flycam FLCM-NANO-QR Manual de usuario
Flycam
Flycam FLOWLINE 600N Manual de usuario
Flycam
Flycam HD-5000 Manual de usuario
Flycam
Flycam Swivel Manual de usuario
Flycam
Flycam FLCM-FLN Manual de usuario
