Fluke T5-600 Manual de usuario

PN 1629509 (English) July 1997, Rev. 2, 9/01

T5-600/T5-1000

Electrical Tester Instruction Sheet

Read First: Safety Information

If this product is used in a manner not specified by the

manufacturer, the protection provided by the equipment may be

impaired.

Warning

•Do not use the tester if it is damaged or operating abnormally.

Protection may be impaired.

•Before each use:

•Make sure the battery door is closed and latched.

•Inspect the tester and test leads. Look for cracks, missing

plastic, exposed metal, or damaged insulation. Replace

damaged test leads before using the tester.

•Verify the tester’s operation by measuring a known voltage.

•Replace the batteries as soon as the low battery indicator (

)

appears.

•Do not use the tester around explosive gas, vapor or dust.

•Do not apply more than the rated voltage, as marked on the

tester, between terminals or between any terminal and earth

ground.

•Refer servicing to qualified personnel.

•Use caution when working above 30 V ac rms, 42 V ac peak, or

60 V dc.

•When using the probes, keep your fingers behind the finger

guards on the probes.

•Connect the common test lead before you connect the live test

lead. Disconnect the live test lead first.

•The display will not display hazardous voltages in display hold.

The voltage indicator LED ( ) continues to operate.

Symbols

BAC (alternating current) JEarth ground

FDC (direct current) TDouble insulated

MBattery

WCaution, risk of danger

(refer to the manual.) XCaution, shock hazard

Voltage Indicator

While the tester is on, the LED glows when more than 30 V ac or 60 V

dc is present across the leads. (The LED can also glow at lower

voltages.) Be aware that such voltages pose a shock hazard.

Measuring Voltage

(V)

The tester automatically selects dc (DC) or ac (AC) voltage mode based

on the peak values of the measured signal.

The tester defaults to ac voltage when turned on.

DC Voltage

T5-600 maximum: 600 V CAT III

T5-1000 maximum: 1000 V, also

600 V CAT IV

AC Voltage

45 Hz to 66 Hz

T5-600 maximum: 600 V rms

T5-1000 maximum: 1000 V rms,

also 600V rms CAT IV

AC/DC

Automatic

Selection

AC/DC

Automatic

Selection

ex2.eps

Measuring Continuity and Resistance

(Ω)

Continuity Resistance

1000 Ω

Range

Greater than

400 Ω

Open Short

Less than

25 Ω

ex3.eps

Beeper indicates shorts lasting 10 ms (1/100 second) or longer.

Measuring AC Current

(A)

0.5"(12.9 mm)

maximum

ex1.eps

•Range: 0 A to 100.0 A;

45 Hz to 66 Hz

•

Do not connect test

probes to voltages while

measuring current.

•Place conductor

anywhere within the

sensor zone (shaded

area shown below).

OKOK

OK OK

Sensor

Zone

ex5.eps

Display Hold

To hold the reading on the display, press and release HOLD. The

display will not display hazardous voltages in display hold. The voltage

indicator LED ( ) continues to operate.

To exit the display hold mode, press and release HOLD again, or turn

the rotary switch to a new position.

Automatic Power Down

The tester turns off automatically if you do not turn the rotary switch or

press HOLD for approximately 45 minutes. To resume operation, turn

the tester off, then turn the tester on.

Low Battery Indicator

Warning

To avoid false readings, which could lead to possible

electric shock or personal injury, replace the battery as

soon as the low battery indicator (

)appears.

Maintenance

Clean the case with a damp cloth and detergent. Do not use abrasives

or solvents.

Because the inputs are electronically protected, no fuses are required.

Battery Replacement

Observe the polarity markings inside the battery compartment.

Do not

overtighten screw

Disconnect probes

from Voltage

Switch OFF

2 AA

ex4.eps

Replacement Parts

Test Lead Assembly.

Replace only with Fluke double-insulated leads (

)

See "Accessories" for available probes.

PN 648029

Battery Door PN 1626588

Battery Door Screw PN 1618578

Accessories

H5 Belt Holster

TP1 Probe Set, Flat-Blade

TP4 Probe Set, 4 mm round

Service Information Sheet

, PN 686953

To contact Fluke, call:

USA: 1-888-99-FLUKE (1-888-993-5853)

Canada: 1-800-36-FLUKE (1-800-363-5853)

Europe: +31 402-678-200

Japan: +81-3-3434-0181

Singapore: +65-738-5655

Anywhere in the world: +1-425-446-5500

Visit Fluke’s Web site at www.fluke.com.

Specifications

Specifications subject to change without notice.

Calibration: One-year calibration cycle.

Maximum Voltage Between any Terminal and Earth Ground:

T5-600: 600 V rms, Overvoltage Category III; Pollution Degree 2

T5-1000: 1000 V rms, Overvoltage Category III, also 600 V rms

overvoltage Category IV, Pollution Degree 2

Maximum Voltage between Current Fork and Earth Ground: T5-600

and T5-1000: 1000 V rms, Overvoltage Category III, also 600 V rms,

Overvoltage Category IV, Pollution Degree 2, (This dual rating applies

to the current fork only.)

Temperature: Operating: -10 °C to +50 °C (14 °F to 122 °F);

Storage: -30 °C to +60 °C (-22 °F to +140 °F)

Altitude: Operating: 2000 m (6562 ft); Storage: 10,000 m (32808 ft)

Relative Humidity: 0 % to 95 %, 5 °C to 30 °C (41 °F to 86 °F); 0 % to

75 %, 30 °C to 40 °C (86 °F to 104 °F); 0 % to 45 %, 40 °C to 50 °C

(104 °F to 122 °F)

Battery Type and Life: AA (2); 360 hours continuous with alkaline;

125 hours continuous with zinc chloride

Shock, Vibration: 1 m drop at -10 °C to 50 °C (14 °F to 122 °F) per

ANSI/ISA-S82.01-1994 and EN 61010-1: 1995. Random vibration per

MIL-PRF-28800F for a Class 2 instrument (5 Hz to 55 Hz, 3 g

maximum).

Surge Protection: T5-600 6 kV per IEC 61010;

T5-1000 8 kV per IEC 61010

Enclosure Rating: IP 52 per IEC 60529, no vacuum applied

RF Field Specification: 0.5 % full scale + (specified accuracy) at

3 V / m

Safety: Complies with ANSI/ISA-S82.01-94, UL classified to IEC

61010, CSA/CAN C22.2 No.1010.1-92, and EN 61010-1: 1995.

EMC: EN 61326

Certifications: In accordance with

IEC 61010-1 54CJ

Accuracy is specified for 1 year after calibration, at 18 °C to 28 °C

(64 °F to 82 °F) with relative humidity to 90 %. AC conversions are ac-

coupled, average responding, and calibrated to the rms value of a sine

wave input.

Accuracy specifications are given as follows:

±( [ % of reading] + [number of least significant digits] )

Temperature coefficient of 0.1 x (specified accuracy) / °C for <18 °C

or >28 °C (< 64.4 °F or > 82.4 °F)

Function T5-600

Range T5-1000

Range Reso-

lution Accuracy

600 V rms 1000 V rms 1 V ±(1.5 % + 2 digits)

600 V 1000 V 1 V ±(1 % + 1 digit)

100.0 A 100.0 A 0.1 A ±(3 % + 3 digits)

1000 Ω1000 Ω1 Ω±

(1 % + 2 digits)

Input Protection

Function T5-600 T5-1000

Input Impedance

(nominal)

600 V rms 1000 V rms 1 MΩ, <100 pF ac-coupled

600 V rms 1000 V rms 1 MΩ, <100 pF

600 V rms 1000 V rms ---

Function Open Circuit Test

Voltage Short Circuit

Current

1.65 V dc (nominal) <0.6 mA

CAT III protects against transients in a

fixed equipment installation

such

as a distribution panel, and lighting systems in large buildings.

CAT IV protects against transients from a

primary supply

such as an

electricity meter or an overhead or underground utility service.

Limited Warranty & Limitation Of Liability

This Fluke product will be free from defects in material and

workmanship for two years from the date of purchase. This

warranty does not cover fuses, disposable batteries, or damage

from accident, neglect, misuse or abnormal conditions of operation

or handling. Resellers are not authorized to extend any other

warranty on Fluke’s behalf. To obtain service during the warranty

period, send the defective product to the nearest Fluke Authorized

Service Center with a description of the problem.

THIS WARRANTY IS YOUR ONLY REMEDY. NO OTHER

WARRANTIES, SUCH AS FITNESS FOR A PARTICULAR

PURPOSE, ARE EXPRESSED OR IMPLIED. FLUKE IS NOT

LIABLE FOR ANY SPECIAL, INDIRECT, INCIDENTAL OR

CONSEQUENTIAL DAMAGES OR LOSSES, ARISING FROM

ANY CAUSE OR THEORY.

Since some states or countries do not allow the exclusion or

limitation of an implied warranty or of incidental or consequential

damages, this limitation of liability may not apply to you.

10/96

Otros manuales para T5-600

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Equipo de prueba de Fluke

Fluke

Fluke 718-100US Manual de usuario

Fluke

Fluke 1550C Manual de usuario

Fluke

Fluke TS22 Manual de usuario

Fluke

Fluke 5500A Manual de usuario

Fluke

Fluke T+ Manual de usuario

Fluke

Fluke i1000s Manual de uso y cuidado

Fluke

Fluke ScopeMeter 190-502 Manual de usuario

Fluke

Fluke Versiv Series Manual de usuario

Fluke

Fluke 714 Manual de usuario

Fluke

Fluke 5820A Manual de usuario

Fluke

Fluke 5100 Series Manual de usuario

Fluke

Fluke 1621 Manual de usuario

Fluke

Fluke 80PK-27 Manual de usuario

Fluke

Fluke 1550C Manual de usuario

Fluke

Fluke 5440B/AF Manual de usuario

Fluke

Fluke 719PRO Manual de usuario

Fluke

Fluke 744 Manual de usuario

Fluke

Fluke CopperPro 990 Manual de usuario

Fluke

Fluke 700PA3 Manual de usuario

Fluke

Fluke 5520A Service Manual de usuario

Fluke

Fluke P3100 Series Manual de usuario

Fluke

Fluke 525A Manual de usuario

Fluke

Fluke NFK-LAUNCH Series Manual de usuario

Fluke

Fluke FTK200 Manual de usuario

Manuales populares de Equipo de prueba de otras marcas

SMART

SMART KANAAD SBT XTREME 3G Series Manual de usuario

Agilent Technologies

Agilent Technologies BERT Serial Manual de usuario

Agilent Technologies

Agilent Technologies N3280A Manual de usuario

Vernier

Vernier Go Direct Voltage Manual de usuario

Lifeloc

Lifeloc R.A.D.A.R. Manual de usuario

Mercury

Mercury TSL01 Manual de usuario

MAHA

MAHA MBT Series Manual de usuario

Fuji Electric

Fuji Electric P-61 Manual de usuario

ETC

ETC SealerAtor Manual de usuario

Skyfine

Skyfine ETHYWAY V2 Manual de usuario

Appion

Appion G5 Twin Manual de usuario

PCB Piezotronics

PCB Piezotronics 8159-0112A Manual de usuario

BW Technologies

BW Technologies MicroDock II Manual de usuario

Sun Nuclear

Sun Nuclear 1027 Manual de usuario

Biomark

Biomark HPR LITE READER Manual de usuario

Hioki

Hioki 3169-20 Manual de usuario

Ashcroft

Ashcroft ATE-100 Manual de usuario

Rohde & Schwarz

Rohde & Schwarz RTA4000 Manual de usuario