Fluke 753 Manual de usuario
LIMITED WARRANTY AND LIMITATION OF LIABILITY
This Fluke product will be free from defects in material and workmanship for three years from the date of purchase. This
warranty does not cover fuses, disposable batteries, or damage from accident, neglect, misuse, alteration, contamination, or
abnormal conditions of operation or handling. Resellers are not authorized to extend any other warranty on Fluke’s behalf.
To obtain service during the warranty period, contact your nearest Fluke authorized service center to obtain return
authorization information, then send the product to that Service Center with a description of the problem.
THIS WARRANTY IS YOUR ONLY REMEDY. NO OTHER WARRANTIES, SUCH AS FITNESS FOR A PARTICULAR
PURPOSE, ARE EXPRESSED OR IMPLIED. FLUKE IS NOT LIABLE FOR ANY SPECIAL, INDIRECT, INCIDENTAL OR
CONSEQUENTIAL DAMAGES OR LOSSES, ARISING FROM ANY CAUSE OR THEORY. Since some states or countries
do not allow the exclusion or limitation of an implied warranty or of incidental or consequential damages, this limitation of
liability may not apply to you.
Fluke Corporation
P.O. Box 9090
Everett, WA 98206-9090
U.S.A.
Fluke Europe B.V.
P.O. Box 1186
5602 BD Eindhoven
The Netherlands
11/99
i
Table of Contents
Title Page
Introduction .................................................................................................................... 1
How to Contact Fluke..................................................................................................... 1
Safety Information .......................................................................................................... 2
Before You Begin ........................................................................................................... 3
Standard Equipment....................................................................................................... 4
Operation Features ........................................................................................................ 6
Input and Output Jacks.............................................................................................. 6
Buttons ...................................................................................................................... 8
The Battery..................................................................................................................... 10
Display Languages......................................................................................................... 11
753/754
Getting Started
ii
1
Introduction
The 753 and 754 Documenting Process Calibrators (the
Product) are battery-powered, hand-held instruments that
measure and source electrical and physical parameters.
In addition, the 754 supplies basic HARTcommunicator
functions when used with HART-capable transmitters.
See the 754 HART Mode Users Guide for instructions on
how to use the HART communication feature.
The Product helps troubleshoot, calibrate, verify, and
document work performed on process instruments.
Notes
•All figures in this manual show the 754.
•For more instruction and information,
see the 753/754 Users Manual on the
Product CD.
How to Contact Fluke
To contact Fluke, call one of the following telephone
numbers:
•Technical Support USA: 1-800-44-FLUKE
(1-800-443-5853)
•Calibration/Repair USA: 1-888-99-FLUKE
(1-888-993-5853)
•Canada: 1-800-36-FLUKE (1-800-363-5853)
•Europe: +31 402-675-200
•Japan: +81-3-3434-0181
•Singapore: +65-738-5655
•Anywhere in the world: +1-425-446-5500
Or, visit Fluke's website at www.fluke.com.
To register your product, visit http://register.fluke.com.
To view, print, or download the latest manual supplement,
visit http://us.fluke.com/usen/support/manuals.
The latest software trial version of DPCTrack2 can be
downloaded at www.fluke.com/DPCTrack. For more
information see “Communication with a PC”.
753/754 Accessories can be found at
www.fluke.com/process_acc.
753/754
Getting Started
2
Safety Information
Warning
To prevent personal injury, use the Product
only as specified, or the protection supplied
by the Product can be compromised.
To prevent possible electrical shock, fire, or
personal injury:
•Read all safety Information before you
use the Product.
•Carefully read all instructions.
•Use only correct measurement category
(CAT), voltage, and amperage rated
probes, test leads, and adapters for the
measurement.
•The battery must be locked in place
before you operate the Product.
•Recharge the battery when the low
battery indicator shows to prevent
incorrect measurements.
•Do not apply more than the rated
voltage, between the terminals or
between each terminal and earth ground.
•Limit operation to the specified
measurement category, voltage, or
amperage ratings.
•Do not exceed the Measurement
Category (CAT) rating of the lowest rated
individual component of a Product,
probe, or accessory.
•Measure a known voltage first to make
sure that the Product operates correctly.
•Do not touch voltages > 30 V ac rms, 42 V
ac peak, or 60 V dc.
•Do not use the Product around explosive
gas, vapor, or in damp or wet
environments.
•Do not use and disable the Product if it
is damaged.
•Do not use the Product if it operates
incorrectly.
•Keep fingers behind the finger guards on
the probes.
•Remove all probes, test leads, and
accessories that are not necessary for
the measurement.
•Only use probes, test leads, and
accessories that have the same
measurement category, voltage, and
amperage ratings as the Product.
•Connect the common test lead before
the live test lead and remove the live test
lead before the common test lead.
Documenting Process Calibrators
Before You Begin
3
•Use only current probes, test leads, and
adapters supplied with the Product.
•Do not touch the probes to a voltage
source when the test leads are
connected to the current terminals.
•Use only cables with correct voltage
ratings.
•Do not use test leads if they are
damaged. Examine the test leads for
damaged insulation, exposed metal, or if
the wear indicator shows. Check test
lead continuity.
•Examine the case before you use the
Product. Look for cracks or missing
plastic. Carefully look at the insulation
around the terminals.
Before You Begin
After you unpack the Product, charge the battery for 8
hours (if the battery is outside of the Product, charge for 5
hours). For more information, see “The Battery” in the
753/754 Users Manual. When the Battery is inside the
Product, it will only charge if the Product is off.
753/754
Getting Started
4
Standard Equipment
Items included with the product are shown in Figure 1.
Fluke-75X-Stackable
Test Lead Set (3 Red and 3 Black)
Jumper
TC Cap
TP220-1
Test Probe
(3 Red and 3 Black)
Strap
754-8016,
Alligator Clip Set
(3 Red and 3 Black)
AC280 SureGrip
TM
Hook Clip Set
(2 Red and 2 Black)
gks01f.eps
Figure 1. Standard Equipment
Documenting Process Calibrators
Standard Equipment
5
753/754 Getting
Started
753/754 Manuals
CD
DPCTrack2
CD
Lithium Ion
Battery Pack
USB Cable
HART
Communication
Cable
Battery Charger/Universal Power Supply
gks02f.eps
Figure 1. Standard Equipment (cont)
753/754
Getting Started
6
Operation Features
Input and Output Jacks
Figure 2 shows the input and output jacks and connectors. Table 1 explains their use.
Table 1. Input/Output Jacks and Connectors
No. Name Description
HART jack (754 only) Connects the Product to HART devices.
Pressure module
connector Connects the Product to a pressure module.
TC input/output
Jack to measure or simulate thermocouples. This jack accepts a miniature
polarized thermocouple plug with flat, in-line blades spaced 7.9 mm (0.312 in)
center to center.
,MEASURE V jacks Input jacks to measure voltage, frequency, or three- or four-wire RTDs
(Resistance Temperature Detectors).
,
SOURCE mA,
MEASURE mA ΩRTD
jacks
Jacks to source or measure current, measure resistance and RTDs, and supply
loop power.
,SOURCE V ΩRTD
jacks Output jacks to source voltage, resistance, frequency, and to simulate RTDs.
Battery Charger jack
Jack for the battery charger/universal power supply (referred to as the battery
charger throughout this manual). Use the battery charger for bench-top
applications where ac line power is available.
USB port (Type 2) Connects the Product to a USB port on a PC.
Otros manuales para 753
6
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Equipo de prueba de Fluke
Fluke
Fluke ScopeMeter 190-202 Manual de usuario
Fluke
Fluke MicroNetBlink Kit Manual de usuario
Fluke
Fluke 975 AirMeter Manual de usuario
Fluke
Fluke 190-062/AM Manual de operación
Fluke
Fluke 6270A Manual de usuario
Fluke
Fluke 5730A/03 Manual de usuario
Fluke
Fluke ST120 Manual de usuario
Fluke
Fluke 6003A Manual de usuario
Fluke
Fluke 154 HART Manual de usuario
Fluke
Fluke 1550C Manual de usuario
Fluke
Fluke 80T-150U Manual de usuario
Fluke
Fluke 5623B Manual de usuario
Fluke
Fluke 990DSL Manual de usuario
Fluke
Fluke DTX-CLT CertiFiber Manual de usuario
Fluke
Fluke SimpliFiber Pro Manual de usuario
Fluke
Fluke T+ Manual de usuario
Fluke
Fluke CableIQ Manual de usuario
Fluke
Fluke 717-10000G Manual de usuario
Fluke
Fluke 9500B Manual de instrucciones
Fluke
Fluke 718 30G Manual de usuario
Manuales populares de Equipo de prueba de otras marcas
SMART
SMART KANAAD SBT XTREME 3G Series Manual de usuario
Agilent Technologies
Agilent Technologies BERT Serial Manual de usuario
Agilent Technologies
Agilent Technologies N3280A Manual de usuario
Vernier
Vernier Go Direct Voltage Manual de usuario
Lifeloc
Lifeloc R.A.D.A.R. Manual de usuario
Mercury
Mercury TSL01 Manual de usuario
