Fluke 753 Manual de usuario
PN 3377694
July 2011 Rev. 2, 7/23
© 2011-2023 Fluke Corporation. All rights reserved.
All product names are trademarks of their respective companies.
753/754
Documenting Process Calibrator
Getting Started
LIMITED WARRANTY AND LIMITATION OF LIABILITY
This Fluke product will be free from defects in material and workmanship for three years from the date of purchase. This
warranty does not cover fuses, disposable batteries, or damage from accident, neglect, misuse, alteration, contamination, or
abnormal conditions of operation or handling. Resellers are not authorized to extend any other warranty on Fluke’s behalf.
To obtain service during the warranty period, contact your nearest Fluke authorized service center to obtain return
authorization information, then send the product to that Service Center with a description of the problem.
THIS WARRANTY IS YOUR ONLY REMEDY. NO OTHER WARRANTIES, SUCH AS FITNESS FOR A PARTICULAR
PURPOSE, ARE EXPRESSED OR IMPLIED. FLUKE IS NOT LIABLE FOR ANY SPECIAL, INDIRECT, INCIDENTAL OR
CONSEQUENTIAL DAMAGES OR LOSSES, ARISING FROM ANY CAUSE OR THEORY. Since some states or countries
do not allow the exclusion or limitation of an implied warranty or of incidental or consequential damages, this limitation of
liability may not apply to you.
Fluke Corporation
P.O. Box 9090
Everett, WA 98206-9090
U.S.A.
Fluke Europe B.V.
P.O. Box 1186
5602 BD Eindhoven
The Netherlands
11/99
i
Table of Contents
Title Page
Introduction .................................................................................................................... 1
How to Contact Fluke ..................................................................................................... 1
Safety Information .......................................................................................................... 2
Symbols ......................................................................................................................... 4
Before You Begin ........................................................................................................... 6
Standard Equipment....................................................................................................... 6
Operation Features ........................................................................................................ 10
Input and Output Jacks.............................................................................................. 10
Buttons ...................................................................................................................... 12
The Battery..................................................................................................................... 14
Display Languages......................................................................................................... 15
Safety Specifications ...................................................................................................... 15
753/754
Getting Started
ii
1
Introduction
The 753 and 754 Documenting Process Calibrators (the
Product) are battery-powered, hand-held instruments that
measure and source electrical and physical parameters.
In addition, the 754 supplies basic HARTcommunicator
functions when used with HART-capable transmitters.
See the 754 HART Mode Users Guide for instructions on
how to use the HART communication feature.
The Product helps troubleshoot, calibrate, verify, and
document work performed on process instruments.
Note
All figures in this manual show the 754.
How to Contact Fluke
Fluke Corporation operates worldwide. For local contact
information, go to our website: www.fluke.com
To register your product, view, print, or download the
latest manual or manual supplement, go to our website.
+1-425-446-5500
The latest software trial version of DPCTrack2 can be
downloaded at www.fluke.com/DPCTrack. For more
information see Communication with a PC in the Users
Manual.
753/754 Accessories can be found at
www.fluke.com/process_acc.
753/754
Getting Started
2
Safety Information
XW Warning
To prevent personal injury, use the Product
only as specified, or the protection supplied
by the Product can be compromised.
To prevent possible electrical shock, fire, or
personal injury:
•Read all safety Information before you
use the Product.
•Carefully read all instructions.
•Use only correct measurement category
(CAT), voltage, and amperage rated
probes, test leads, and adapters for the
measurement.
•The battery must be locked in place
before you operate the Product.
•Recharge the battery when the low
battery indicator shows to prevent
incorrect measurements.
•Do not apply more than the rated
voltage, between the terminals or
between each terminal and earth ground.
•Limit operation to the specified
measurement category, voltage, or
amperage ratings.
•Do not exceed the Measurement
Category (CAT) rating of the lowest rated
individual component of a Product,
probe, or accessory.
•Measure a known voltage first to make
sure that the Product operates correctly.
•Do not touch voltages > 30 V ac rms,
42 V ac peak, or 60 V dc.
•Do not use the Product around explosive
gas, vapor, or in damp or wet
environments.
•Do not use and disable the Product if it
is damaged.
•Do not use the Product if it operates
incorrectly.
•Keep fingers behind the finger guards on
the probes.
•Remove all probes, test leads, and
accessories that are not necessary for
the measurement.
•Only use probes, test leads, and
accessories that have the same
measurement category, voltage, and
amperage ratings as the Product.
•Connect the common test lead before
the live test lead and remove the live test
lead before the common test lead.
Documenting Process Calibrator
Safety Information
3
•Use only current probes, test leads, and
adapters supplied with the Product.
•Do not touch the probes to a voltage
source when the test leads are
connected to the current terminals.
•Use only cables with correct voltage
ratings.
•Do not use test leads if they are
damaged. Examine the test leads for
damaged insulation, exposed metal, or if
the wear indicator shows. Check test
lead continuity.
•Examine the case before you use the
Product. Look for cracks or missing
plastic. Carefully look at the insulation
around the terminals.
•Always put the stackable end of the test
lead into a terminal of the Product.
753/754
Getting Started
4
Symbols
Symbols used on the Product and in this manual are explained in Table 1.
Table 1. Symbols
Symbol Meaning Symbol Meaning
WWARNING - RISK OF DANGER. JEarth
X WARNING. HAZARDOUS VOLTAGE. Risk of
electric shock. »Consult user documentation.
, Application around and removal from uninsulated
hazardous live conductors is permitted. PConforms to European Union directives.
TDouble insulated ˜Equipotential
¼
Measurement Category II is applicable to test and
measuring circuits connected directly to utilization
points (socket outlets and similar points) of the low-
voltage MAINS installation.
BAC (Alternating Current)
Documenting Process Calibrator
5
Table 1. Symbols (cont.)
SymbolMeaning Symbol Meaning
fPressure ´
This product contains a Lithium-ion battery. Do
not mix with solid waste stream. Spent batteries
should be disposed of by a qualified recycler or
hazardous materials handler per local regulations.
Contact your authorized Fluke Service Center for
recycling information.
FDC (Direct Current) ~
This product complies with the WEEE Directive
and its marking requirements. The affixed label
indicates that you must not discard this
electrical/electronic product in domestic
household waste. Do not dispose of this product
as unsorted municipal waste. For information
about take-back and recycling programs available
in your country, see the Fluke website.
753/754
Getting Started
6
Before You Begin
After you unpack the Product, charge the battery for
8 hours (if the battery is outside of the Product, charge for
5 hours). For more information, see The Battery in the
753/754 Users Manual. When the Battery is inside the
Product, it will only charge if the Product is off.
Standard Equipment
Items included with the Product are shown in Figure 1
and Table 2.
These items are also available:
•Calibration Manual (available from the Fluke website)
•Sample DPCTrack2 application software (available
from the Fluke website)
•NIST-traceable Certificate of Calibration
Otros manuales para 753
6
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Equipo de prueba de Fluke
Fluke
Fluke PM3082 Manual de usuario
Fluke
Fluke CableAnalyzer DSX-500 Manual de usuario
Fluke
Fluke 5520A Service Manual
Fluke
Fluke 753 Manual de usuario
Fluke
Fluke 1550C Manual de uso y cuidado
Fluke
Fluke FiberInspector Pro FI-7000 Manual de usuario
Fluke
Fluke 1000FLT Manual de usuario
Fluke
Fluke 725Ex Manual de usuario
Fluke
Fluke T5-600 Manual de usuario
Fluke
Fluke 52801RJ9 Manual de usuario
Fluke
Fluke NX1 Pocket Toner Manual de usuario
Fluke
Fluke 705 Manual de usuario
Fluke
Fluke 6270A Manual de usuario
Fluke
Fluke i400 Manual de uso y cuidado
Fluke
Fluke 5522A Operators Manual de usuario
Fluke
Fluke 5730A Manual de usuario
Fluke
Fluke AIRCHECK Manual de usuario
Fluke
Fluke 714C Manual de usuario
Fluke
Fluke 4181 Manual de usuario
Fluke
Fluke 705 Manual de usuario
Manuales populares de Equipo de prueba de otras marcas
SMART
SMART KANAAD SBT XTREME 3G Series Manual de usuario
Agilent Technologies
Agilent Technologies BERT Serial Manual de usuario
Agilent Technologies
Agilent Technologies N3280A Manual de usuario
Vernier
Vernier Go Direct Voltage Manual de usuario
Lifeloc
Lifeloc R.A.D.A.R. Manual de usuario
Mercury
Mercury TSL01 Manual de usuario
