Fluke VT650 Manual de usuario
VT650/VT900
Gas Flow Analyzer
Users Manual
FBC - 0099
October 2017, Rev. 1
©2017 Fluke Corporation. All rights reserved. All product names are trademarks of their respective companies.
Warranty and Product Support
Fluke Biomedical warrants this instrument against defects in materials and workmanship for one year from the date of original purchase OR two
years if at the end of your first year you send the instrument to a Fluke Biomedical service center for calibration. You will be charged our
customary fee for such calibration. During the warranty period, we will repair or at our option replace, at no charge, a product that proves to be
defective, provided you return the product, shipping prepaid, to Fluke Biomedical. This warranty covers the original purchaser only and is not
transferable. The warranty does not apply if the product has been damaged by accident or misuse or has been serviced or modified by anyone
other than an authorized Fluke Biomedical service facility. NO OTHER WARRANTIES, SUCH AS FITNESS FOR A PARTICULAR PURPOSE,
ARE EXPRESSED OR IMPLIED. FLUKE SHALL NOT BE LIABLE FOR ANY SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL
DAMAGES OR LOSSES, INCLUDING LOSS OF DATA, ARISING FROM ANY CAUSE OR THEORY.
This warranty covers only serialized products and their accessory items that bear a distinct serial number tag. Recalibration of instruments is
not covered under the warranty.
This warranty gives you specific legal rights and you may also have other rights that vary in different jurisdictions. Since some jurisdictions do
not allow the exclusion or limitation of an implied warranty or of incidental or consequential damages, this limitation of liability may not apply to
you. If any provision of this warranty is held invalid or unenforceable by a court or other decision-maker of competent jurisdiction, such holding
will not affect the validity or enforceability of any other provision.
7/07
Notices
All Rights Reserved
Copyright 2017, Fluke Biomedical. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval
system, or translated into any language without the written permission of Fluke Biomedical.
Copyright Release
Fluke Biomedical agrees to a limited copyright release that allows you to reproduce manuals and other printed materials for use in
service training programs and other technical publications. If you would like other reproductions or distributions, submit a written
request to Fluke Biomedical.
Unpacking and Inspection
Follow standard receiving practices upon receipt of the instrument. Check the shipping carton for damage. If damage is found, stop
unpacking the instrument. Notify the carrier and ask for an agent to be present while the instrument is unpacked. There are no special
unpacking instructions, but be careful not to damage the instrument when unpacking it. Inspect the instrument for physical damage
such as bent or broken parts, dents, or scratches.
Technical Support
For application support or answers to technical questions, either email [email protected] or call 1-800- 850-4608 or
1-440-248-9300 (Europe +31-40-2965314).
Claims
Our routine method of shipment is via common carrier, FOB origin. Upon delivery, if physical damage is found, retain all packing
materials in their original condition and contact the carrier immediately to file a claim. If the instrument is delivered in good physical
condition but does not operate within specifications, or if there are any other problems not caused by shipping damage, please contact
Fluke Biomedical or your local sales representative.
Returns and Repairs
Return Procedure
All items being returned (including all warranty-claim shipments) must be sent freight-prepaid to our factory location. When you return
an instrument to Fluke Biomedical, we recommend using United Parcel Service, Federal Express, or Air Parcel Post. We also
recommend that you insure your shipment for its actual replacement cost. Fluke Biomedical will not be responsible for lost shipments or
instruments that are received in damaged condition due to improper packaging or handling.
Use the original carton and packaging material for shipment. If they are not available, we recommend the following guide for
repackaging:
• Use a double–walled carton of sufficient strength for the weight being shipped.
• Use heavy paper or cardboard to protect all instrument surfaces. Use nonabrasive material around all projecting parts.
• Use at least four inches of tightly packed, industry-approved, shock-absorbent material around the instrument.
Returns for partial refund/credit:
Every product returned for refund/credit must be accompanied by a Return Material Authorization (RMA) number, obtained from our
Order Entry Group at 1-440-498-2560.
Repair and calibration:
To find the nearest service center, go to www.flukebiomedical.com/service or
To ensure the accuracy of the Product is maintained at a high level, Fluke Biomedical recommends the product be calibrated at least
once every 12 months. Calibration must be done by qualified personnel. Contact your local Fluke Biomedical representative for
calibration.
Certification
This instrument was thoroughly tested and inspected. It was found to meet Fluke Biomedical’s manufacturing specifications when it
was shipped from the factory. Calibration measurements are traceable to the National Institute of Standards and Technology (NIST).
Devices for which there are no NIST calibration standards are measured against in-house performance standards using accepted test
procedures.
WARNING
Unauthorized user modifications or application beyond the published specifications may result in electrical shock hazards or improper
operation. Fluke Biomedical will not be responsible for any injuries sustained due to unauthorized equipment modifications.
Restrictions and Liabilities
Information in this document is subject to change and does not represent a commitment by Fluke Biomedical. Changes made to the
information in this document will be incorporated in new editions of the publication. No responsibility is assumed by Fluke Biomedical
for the use or reliability of software or equipment that is not supplied by Fluke Biomedical, or by its affiliated dealers.
Manufacturing Location
The VT650/VT900 Gas Flow Analyzer is manufactured at Fluke Biomedical, 6920 Seaway Blvd., Everett, WA, U.S.A.
In the U.S.A. and Asia:
Cleveland Calibration Lab
Tel: 1-800-850-4608 x2564
Email: [email protected]
In Europe, Middle East, and Africa:
Eindhoven Calibration Lab
Tel: +31-40-2675300
Email: [email protected]
i
Table of Contents
Title Page
Introduction .................................................................................................... 1
Key Features .................................................................................................. 1
Safety Information .......................................................................................... 2
Unpacking and Inspection .............................................................................. 5
Accessories .................................................................................................... 6
The Analyzer .................................................................................................. 8
Power On the Analyzer ......................................................................... 10
Analyzer Connections ........................................................................... 12
Airway Flow (Inlet and Exhaust) .................................................... 12
Ultra-Low Flow + and - (VT900) .................................................... 13
High Pressure ............................................................................... 13
Low Pressure (+ and -) .................................................................. 14
Ultra-Low Pressure (VT900 only) .................................................. 14
Test Setup .................................................................................................... 15
Bi-directional Flow Mode ....................................................................... 15
VT650/VT900
Users Manual
ii
Unidirectional Flow Mode ......................................................................16
Inspiratory Flow Connections ........................................................ 16
Expiratory Test Connections ......................................................... 17
Operations .................................................................................................... 18
Measured Signals .................................................................................18
Airway Flow ................................................................................... 19
Airway Pressure ............................................................................ 19
Airway Temperature and Humidity ................................................ 19
High Pressure ................................................................................19
Low Pressure ................................................................................20
Ultra-Low Pressure (VT900) .......................................................... 20
Ultra-Low Flow (VT900) ................................................................ 20
Barometric Pressure ...................................................................... 20
Oxygen Concentration ...................................................................21
Calculated Breath Parameters ...................................................... 21
Excel Add-in .......................................................................................... 21
Measurements ......................................................................................22
Make a Measurement .................................................................... 22
Save a Measurement .................................................................... 22
Main Menu Functions ............................................................................ 24
Profiles Menu ................................................................................24
Setup Menu ................................................................................... 25
Units ..............................................................................................31
Special Tests Menu ....................................................................... 32
Calibrate Oxygen ........................................................................... 33
Customize Breath Views ............................................................... 34
Contents (continued)
iii
Memory Menu ............................................................................... 34
Test ID ........................................................................................... 34
Maintenance, Service and Calibration ......................................................... 35
Cleaning ................................................................................................ 35
Oxygen Sensor Replacement ............................................................... 36
Battery Status ....................................................................................... 36
Battery Replacement ............................................................................ 37
Replaceable Parts ................................................................................. 38
Service and Calibration ......................................................................... 38
Specifications ............................................................................................... 39
Pressure ................................................................................................ 40
Flow ...................................................................................................... 41
VT650/VT900
Users Manual
iv
1
Introduction
The VT650/VT900 Gas Flow Analyzer (the
Analyzer or Product), is a general purpose gas
flow analyzer with special features for testing
mechanical patient ventilators. The Analyzer
measures bi-directional air flow, high and
differential low pressure, barometric pressure,
Oxygen concentration and airway pressure,
airway temperature and airway humidity. The
VT900 also measures ultra-low flow (±750 ml/
min) and ultra-low pressure (0 mbar to 10 mbar).
The Analyzer can be controlled externally using
USB commands or automated with available
software. The Analyzer operates on a
rechargeable Li-Ion battery or external power
supply for stationary or portable use. All figures
show the VT900 unless otherwise noted.
Key Features
• Full range, bi-directional air flow and volume
channel
• Ultra-low flow and pressure ranges (VT900)
• High pressure, vacuum and differential low
pressure
• Airway pressure, Oxygen concentration,
temperature, and humidity
• Barometric pressure
• External trigger input (VT900)
• Rechargeable Li-ion battery with up to
8 hours battery life
•USB port
• Customizable profiles that can be saved
• Numerical and graphical screens with real
time data
• Automation software available
• On-board memory
VT650/VT900
Users Manual
2
Safety Information
A Warning identifies conditions and actions that
pose hazards to the user; a Caution identifies
conditions and actions that may damage the
Product or the equipment under test.
XW Warning
To prevent possible electrical shock, fire,
or personal injury:
• Read all safety information before
you use the Product.
• Use the Product only as specified, or
the protection supplied by the
Product can be compromised.
• Carefully read all instructions.
• Do not use the Product around
explosive gas, vapor, or in damp or
wet environments.
• Use this Product indoors only.
• Do not use the Product if it operates
incorrectly.
• Disable the Product if it is damaged.
• Do not use the Product if it is
damaged.
• The battery door must be closed and
locked before you operate the
Product.
• Recharge the battery when the low
battery indicator shows to prevent
incorrect measurements. Low
battery will also corrupt the memory
card.
• Remove all probes, test leads, and
accessories before the battery door
is opened.
• Remove all probes, test leads, and
accessories that are not necessary
for the measurement.
• Use only specified replacement
parts.
• Have an approved technician repair
the Product.
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Instrumento de medición de Fluke
Fluke
Fluke NORMA 6003 Manual de usuario
Fluke
Fluke i400s-EL Manual de usuario
Fluke
Fluke i3000s Flex Series Manual de usuario
Fluke
Fluke VIBXPERT II Manual de usuario
Fluke
Fluke i2000flex Manual de usuario
Fluke
Fluke 82RF Manual de usuario
Fluke
Fluke 377 Manual de usuario
Fluke
Fluke 1730 Manual de uso y cuidado
Fluke
Fluke 3210-PR-TF-II Manual de usuario
Fluke
Fluke ProcessMeter 787 Manual de usuario
Fluke
Fluke 374 Manual de usuario
Fluke
Fluke ESA615 Manual de usuario
Fluke
Fluke 724 Manual de uso y cuidado
Fluke
Fluke 726 Guía de configuración
Fluke
Fluke 362 Manual de usuario
Fluke
Fluke endurance series Manual de usuario
Fluke
Fluke ScopeMeter 123 Manual de usuario
Fluke
Fluke 789 Guía de instalación
Fluke
Fluke 323 Manual de usuario
Fluke
Fluke 5790B/3 Manual de usuario
Manuales populares de Instrumento de medición de otras marcas
Endress+Hauser
Endress+Hauser Proline Promag 50 Especificaciones técnicas
Siemens
Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas
KLINGER
KLINGER CMF V Series Manual de usuario
EXFO
EXFO FTB-2 Manual de operación y mantenimiento
Keysight
Keysight M8290A Manual de usuario
ADTEK
ADTEK MW-5 Manual de usuario