Fluke DSX-600 CableAnalyzer Manual de usuario

Copper Cabling

Troubleshooting Handbook

Contents

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Why the need for advanced diagnostics? . . . . . . . . . . . . . . . . . 4

Troubleshooting Basics . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Before you begin testing, you should verify the basics . . . . . . . . . . . 5

Link models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Permanent Link . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Channel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

The automated DSX-600 diagnostics. . . . . . . . . . . . . . . . . . . . .9

Shield Integrity Test . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

HDTDR diagnostics. . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

HDTDX diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Causes of Cabling Faults . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Wiremap. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Length. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Delay/Skew . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Insertion Loss (Attenuation) . . . . . . . . . . . . . . . . . . . . . . . 19

NEXT and PSNEXT . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Return Loss . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

ACR-F and PS ACR-F (older names: ELFEXT and PSELFEXT) . . . . . . . . 22

Resistance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Architects, Consultants and Designers pages . . . . . . . . . . . . . . . 23

Conclusion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

CableAnalyzer Comparison Guide . . . . . . . . . . . . . . . . . . . . . 26

“Certication” is the process of comparing the transmission performance of an

installed cabling system to a standard using a dened method of measuring the

performance. Certication of the cabling system demonstrates component quality

and installation workmanship. It is typically a requirement to obtain the cabling

manufacturer’s warranty. Certication demands that the cabling links yield a “Passing”

result. Technicians must diagnose the failing links and after a corrective action has

been implemented they must retest to ensure the link meets the required transmission

performance. The total time to certify an installation does not only include making the

certication measurements but also documentation and troubleshooting.

Today’s cabling installation professionals must therefore know how to troubleshoot and

diagnose high-performance cabling systems.

Why the need for advanced diagnostics?

As newer high-performance cabling systems have been developed and deployed, every

aspect of the installation demands a higher level of skill and more attention to detail.

New test parameters have been added. The links must be tested using one of two link

models, the Permanent Link or the Channel and the links are tested and evaluated

over a greater frequency range and with more data points. The components with which

these links are constructed need to deliver better performance and the quality of the

workmanship during installation must rise accordingly.

Due to the increased complexity of these cabling systems, determining the cause of

failure and quickly restoring suitable performance has become a challenging task.

This handbook guides you through the troubleshooting of advanced structured cabling

systems using the Fluke Networks DSX-600 CableAnalyzer™ so you can increase your

productivity and deliver better value to your organization.

Most common causes of failures in twisted pair cabling:

Introduction

1. Installation errors: failure to make proper connections while maintaining the wire

pairs and the twist rate in each pair (always keep the “original twist” in each wire

pair as much as practical)

2.Connectors that do not meet the required transmission quality

3.Incorrect tester set up

4.Defects or damage in the installed cable

5.Bad patch cords*

* Patch cords rate high on the list when we are discussing operating networks.

Certication is often executed using the Permanent Link Model since the actual patch

cords used by the operating network are not yet installed or available.

Before you begin testing, you should verify the basics:

• Has the correct test standard been selected? The certication test is executed as

an automated test or an “Autotest”. The test standard you select for an autotest

determines the link model (Permanent Link or Channel), the test parameters to

be measured and the frequency range over which the tests are executed and the

Pass/Fail criteria for each test.

• Has the correct link model been selected?

• Are you using the appropriate test adapter with a plug that matches the jack in the

telecommunication outlet (TO) or the patch panel?

• Has the test reference been set in the last 30 days? It is recommended to set the

reference on a regular basis and at a time that is easy to remember. (Such as at the

beginning of each testing session)

• Are you using the most current version of the tester software?

• Is the NVP set correctly for the cable under test? NVP plays a role when the tester

reports length or distance to a defect

• Is the tester within its operating temperature range and in calibration?

Remember that your Fluke Networks DSX-600 CableAnalyzer™ is a very accurate

instrument that measures small noise disturbances in cables. These instruments are

calibrated in the factory before shipping and this calibration should be veried every

12 months in an authorized Service Center. If the tester has been stored in a colder

or warmer place than the one in which you are working (i.e. overnight in a vehicle),

allow the unit to warm up to its steady-state operating temperature before setting

a reference or executing any measurements. This may take 10 to 15 minutes or more

depending on the temperature differential.

Troubleshooting Basics

The maximum allowed length of the Permanent Link is 90 meters. This link is most

often used by installers to prove the xed portion of the cabling system (excluding

user cords) meets the requirements of ANSI/TIA/EIA-568 or ISO/IEC 11801. The cabling

vendor offering the warranty will require this. If you see an installer making these

measurements using Channel adapters, you may wish to stop them and ask why they are

not making Permanent Link measurements.

Figure 1

To obtain meaningful results, it is essential to select the appropriate autotest and link

model.

Permanent Link

The Permanent Link performance is dened in such a way that after adding good patch

cords to a passing link, the channel performance is automatically met. By good patch

cords, we mean patch cords that pass the same class or category rating as the link or a

higher level of performance.

For this reason, it is recommended that new cabling installations are certied using

the Permanent Link model and test standard. Patch cords and equipment cords may be

changed many times during the life of the permanent link.

Link models

The Permanent Link shown in Figure 1 includes an optional Consolidation Point. Other

Permanent Link models may have a second patch panel instead of the TO which is

typically seen in a Data Center. The Permanent Link measurement includes the RJ45

plug at the end of the test lead, but does not include the cable portion of the test lead

or connection to the test equipment (See Figure 1). In the case of the DSX Permanent

Link adapters, the RJ45 plug is guaranteed to meet the NEXT, FEXT and Return Loss

requirements of the earlier mentioned standards. The cable portion of the test lead is

removed from the measurement using calibration constants stored in the adapter.

Another Permanent Link conguration that’s being seen more often nowadays is the

Modied Permanent Link. This is not recognized in TIA or ISO/IEC, but is supported in

ANSI/BICSI-004. The Modied Permanent Link is used to asses a horizontal link that

results in a direct connection to equipment like a PoE (Power over Ethernet) Wireless

Access point or CCTV camera. To assess this type of link the TIA Permanent Link test limit

must be used. The main tester must be connected via a Permanent Link adapter to the

patch panel. A Channel adapter on the remote unit at the remote end must be used to

connect the RJ45 plug of the direct connection.

Figure 2

Channel

Channel measurements are typically performed when restoring a service or to verify the

existing cabling for application support. The maximum length allowed for a Channel

is 100 meters. It is uncommon to perform Channel tests at the conclusion of a new

installation, since the patch cords that belong to each link are rarely available at that

time. Correct Channel measurements must cancel the effects of the mated connection

in the tester’s channel adapters as seen in Figure 2, which also shows the optional

consolidation point we saw in the Permanent Link. The same Data Center and Direct

equipment links also exist for the Channel.

When an Autotest fails or delivers a “marginal” pass result, the DSX-600 can use its

diagnostic capabilities to nd the cause of the marginal failures.

First, let us review what a marginal test is. The margin of a test is the difference between

the measured value and the applicable Pass/Fail limit value. The margin is positive when

the test passes, negative when the measurement fails and zero when the measured value

is equal to the limit value. A greater margin indicates that the result is further away

from the limit line. A larger positive margin therefore indicates a better test result. A

very small margin means that the test result is close to the limit value. A test result is

called marginal when its margin is less than the accuracy specication of the instrument

for the test parameter. For example, in gure 3, the Return Loss accuracy is +/- 1.79

dB @ 22.5 MHz and the worst case margin of a link at 22.5MHz was 0.4 dB. This Return

Loss result at 22.5 MHz is considered very close to the limit and is called a marginal test

result. A marginal PASS is indicated by PASS*. In this situation, the tester can be set

up to perform HDTDR and HDTDX tests showing diagnostics information to help identify

and point out what may have caused this marginal result. This information provides

the opportunity to quickly locate the problem, correct it, and deliver a link with good

performance. For more information, see the section that discusses HDTDR and HDTDX

diagnostics.

Figure 3

Shows result for worst pair where

the screen has been zoomed to show

the result in more detail. For this TIA

Cat 5e Permanent. Link Return Loss

accuracy is +/- 1.79 dB @ 22.5 MHz.

The margin was 0.4 dB so the result

has fallen within the accuracy band

and therefore is marked PASS*

The automated DSX-600 diagnostics

Figure 4

Shows a wire map failure on wires 6

and 7. Both are open at 1.4 m from

the near end and 4.7 m from the

far end, suggesting the cable has

been severed or not connected at

the same points. Inspect the link at

these points to identify the issue.

If the cabling link fails to pass the wire map test - the test which veries that all 8

wires connect the right pins at either end of the cable - the tester halts and presents a

window saying ‘Warning Bad Wire Map”. If you press OK, then the wire map diagram is

shown with the option to turn ‘SCAN ON’ which may help nd intermittent connection,

or ‘FIX LATER’ which enables you to save the results then go to then next link to be

tested. Alternatively, you can ‘CONTINUE’ which continues the test with the bad wire

map, this may allow you to nd other issues to help you troubleshoot the problem in the

link. Figure 4 shows such a wire map failure. The DSX-600 main unit is always assumed

at the left hand side of these screens, i.e. the near end. The wire map diagram shows

Wire 6 of pair 3/6 and Wire 7 of pair 7/8, both are open at 1.4 Meters at the near end

and 4.7 Meters from the far end. The software halts and asks the operator whether or

not to continue the test. It often makes more sense to tackle the wire map error before

continuing the test. The open wire causes the results for some test parameters to fail. In

this case we continued and the DSX shows a FAIL. At this point we could inspect the link

at 1.4M from the near end to discover the cause of the failure. We could also select the

DIAGNOSTICS tab which enables us to see the results of the HDTDR or HDTDX results.

Otros manuales para DSX-600 CableAnalyzer

Tabla de contenidos

Otros manuales de Instrumento de medición de Fluke

Fluke

Fluke 312 Manual de usuario

Fluke

Fluke ScopeMeter 123B Instrucciones de funcionamiento

Fluke

Fluke BT520 Manual de usuario

Fluke

Fluke DTX Series Manual de usuario

Fluke

Fluke CO-220 Manual de usuario

Fluke

Fluke Victoreen 190 Manual de usuario

Fluke

Fluke 5820A Manual de usuario

Fluke

Fluke 525B Manual de usuario

Fluke

Fluke LinkSprinter 100 Manual de usuario

Fluke

Fluke 9062 Manual de usuario

Fluke

Fluke 789 Manual de uso y cuidado

Fluke

Fluke 724 Manual de usuario

Fluke

Fluke 931 Manual de usuario

Fluke

Fluke FIBER QUICKMAP Manual de usuario

Fluke

Fluke 845AR Manual de usuario

Fluke

Fluke 5606 Manual de usuario

Fluke

Fluke SMFT-1000 Manual de uso y cuidado

Fluke

Fluke PM6681 Manual de usuario

Fluke

Fluke v3000 FC Manual de uso y cuidado

Fluke

Fluke ScopeMeter 190-102 Manual de usuario

Fluke

Fluke FiberInspector Pro FI-3000 Manual de usuario

Fluke

Fluke 1623-2 Manual de usuario

Fluke

Fluke ProcessMeter 787 Manual de uso y cuidado

Fluke

Fluke 917 Series Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario