Fike SHP 10-051 Manual de usuario

Product Manual

Conventional

Fire Alarm/Suppression

System

Manual P/N: 06-130

Rev. No: 3, 04/02

P/N: 10-051

firealarmresources.com

FIKE CORPORATION

UL S2203 SHP Product Manual Page i

FM 0Z8A0.AY Manual P/N: 06-130 Rev. No. 3, 04/02

Fike Corporation - Offices

This document may not be reproduced, in whole or in part, by any means without the prior express written

permission of Fike Corporation.

Fike



is a registered trademark of Fike Corporation.

Disclaimers

The information contained in this manual is as accurate as currently possible. This manual is intended to

be an aid to Fike authorized sales outlets, who have been trained in an approved manner by Fike, and

the user who is a customer of the Fike authorized sales outlet. Fike does not warrant that this manual is

technically correct, complete, or free from writing problems or that the Fike products referenced therein

are free from minor flaws.

In accordance with our policy of continuing product and system improvement, Fike reserves the right to

change designs or specifications without obligation and without further notice.

Reader Responses

Fike encourages input from our sales outlets and end users on how we can improve this manual and the

products themselves. Please direct all calls of this nature to Fike’s Product Support Department

at (816) 229-3405.

Any communication received becomes the property of Fike Corporation.

Warranties

Fike provides a one-year limited manufacturer's warranty on this product. The standard warranty is printed

in each Marketing Price List. All warranty returns must be returned from an authorized Fike Sales outlet.

Contact Fike's Marketing Department for further warranty information. Fike maintains a repair department

that is available to repair and return existing electronic components or exchange/purchase previously

repaired inventory component (advance replacement). All returns must be approved prior to return. A

Material Return Authorization (MRA) number should be indicated on the box of the item being returned.

Contact the appropriate Regional Sales Manager for further information regarding Material Return

Procedures.

Fike Corporation

World Headquarters

704 South 10th Street

P.O. Box 610

Blue Springs, Missouri 64013

U.S.A.

Ph: (816) 229-3405

Fax: (816) 229-5082

Fike Canada

4140 Morris Drive

Burlington, Ontario L7L 5L6

Canada

Ph: (905) 681-3100

Fax: (905) 681-3107

Fike Europe

Toekomstlaan 52

B-2200 Herentals

Belguim

Ph: 011-32-14-210031

Fax: 011-32-14-210743

Fike Latina

Avenida Paulista 2202, 3°, cj34

Cerqueira Cesar, Sao Paulo

Brazil, CEP 01310-300

Ph: 011-55-11-251-5244

Fax: 011-55-11-284-8479

Fike United Kingdom

10-11 Enterprise Estate

Moorfield Road

P.O. Box 540

Guildford, Surrey GU1 1RB

United Kingdom

Ph: 011-44-8700-777-540

Fax: 011-44-7000-777-540

Fike Singapore PTE. LTD.

30, Loyang Way #01-09

Loyand Industrial Estate

Singapore, 509769

Singapore

Ph: 011-65-545-7989

Fax: 011-65-545-6689

firealarmresources.com

FIKE CORPORATION

UL S2203 SHP Product Manual Page ii

FM 0Z8A0.AY Manual P/N: 06-130 Rev. No. 3, 04/02

TABLE OF CONTENTS

Section Page

1.0 Preface................................................................................................................................................... 1

1.1 About This Manual .............................................................................................................. 1

1.2 Product Support .................................................................................................................. 1

1.3 Revision History .................................................................................................................. 1

1.4 Terms Used in this Manual .............................................................................................. 1-3

1.5 Symbols Used in this Manual.............................................................................................. 4

1.6 Safety Notices ..................................................................................................................... 4

2.0 Product Overview ................................................................................................................................ 5

2.1 Product Description............................................................................................................. 5

2.2 Listings and Approvals ........................................................................................................ 5

2.3 Agency Standards and Compliance................................................................................. 5-6

2.4 Related Documentation.......................................................................................................6

2.5 SHP Features...................................................................................................................... 7

3.0 Equipment/Products............................................................................................................................. 9

3.1 Main Panel Hardware..................................................................................................... 9-10

3.2 Input Devices ...............................................................................................................11-12

3.3 Output Devices.................................................................................................................. 12

3.4 Ancillary Devices............................................................................................................... 13

3.5 Spare Parts ....................................................................................................................... 14

3.6 Specifications ............................................................................................................... 15-18

3.7 Enclosure Specifications ................................................................................................... 19

4.0 Installation........................................................................................................................................... 21

4.1 Enclosure Installation ........................................................................................................ 21

4.2 Power and Field Wiring..................................................................................................... 22

4.3 Wiring Verification ............................................................................................................. 23

4.4 System Module Installation ............................................................................................... 23

4.5 System Configuration........................................................................................................ 23

4.6 Wiring Diagrams........................................................................................................... 24-25

4.7 Circuit Configuration..................................................................................................... 26-27

4.8 Initial Power-Up................................................................................................................. 28

4.9 Complete Field Wiring....................................................................................................... 28

4.10 Checkout System .............................................................................................................. 28

4.11 Releasing Hardware..........................................................................................................28

5.0 Operations ........................................................................................................................................... 29

5.1 User Switch Interaction ..................................................................................................... 29

5.2 Diagnostic LED Code Designators ................................................................................... 29

5.3 Silencing Rules ................................................................................................................. 29

5.4 Outputs Disabled Mode..................................................................................................... 30

5.5 Supervisory and Trouble Status LED’s ............................................................................. 30

5.6 Latching versus Non-Latching Troubles ........................................................................... 30

5.7 Waterflow Alarm Operations ............................................................................................. 30

5.8 Supervision Response Times ........................................................................................... 30

5.9 Low Power Conditions ...................................................................................................... 30

5.10 Alarm Operation (Suppression Mode) .............................................................................. 31

5.11 Alarm Operation (Sprinkler Mode) .................................................................................... 32

5.12 Supervisory Operation ...................................................................................................... 32

5.13 Trouble Operation ............................................................................................................. 32

firealarmresources.com

FIKE CORPORATION

Page iii SHP Conventional Fire Suppression Panel UL S2203

Rev. No: 3, 04/02 Manual P/N: 06-130 FM 0Z8A0.AY

6.0 Servicing .............................................................................................................................................. 33

6.1 Checkout ........................................................................................................................... 33

6.2 Maintenance...................................................................................................................... 33

6.3 Troubleshooting ........................................................................................................... 33-36

Appendix 1 ................................................................................................................................................. 37

Battery Calculations .................................................................................................................. 37-38

Appendix 2 ................................................................................................................................................. 39

ULC Operation ............................................................................................................................... 39

Appendix 3 ................................................................................................................................................. 41

System Operation Posting ............................................................................................................. 41

Index ........................................................................................................................................................... 43

firealarmresources.com

FIKE CORPORATION PREFACE

UL S2203 SHP Product Manual Page 1 of 43

FM 0Z8A0.AY Manual P/N: 06-130 Rev. No. 3, 04/02

1.0 PREFACE

1.1 ABOUT THIS MANUAL

This manual is intended to be a complete reference for the installation, operation, and service of the Fike

Single Hazard Panel (SHP) Fire Alarm/Suppression Control System. The information contained in this

manual must be utilized by the factory trained Fike sales outlet in order to properly install, test and service

the SHP. This manual can also be used by the end user as an Operations Manual for the SHP.

Before you refer to any section in this manual, and before you attempt to install or use the SHP, be sure

to read the important safety notices in section 1.6.

This manual is divided into sections for easy reference. The first-time installer and/or user should

thoroughly read and understand the instructions contained within this manual before using this device.

These instructions must be followed to avoid possible damage to the SHP itself or adverse operating

conditions caused by improper installation and programming.

1.2 PRODUCT SUPPORT

If you have a question or encounter a problem not covered in this manual, you should first try to contact

the sales outlet that installed the protection system. Fike has a worldwide distribution network. Each

sales outlet sells, installs, and services Fike equipment. Look on the inside door, left side, there should

be a sticker with an indication of the sales outlet who sold the system. If you can not locate the sales

outlet, please call Fike Customer Service for locating your nearest sales outlet, or go to our web-site at

www.fike.com. If you are unable to contact your installing sales outlet or you simply do not know who

installed the system you can contact Fike Product Support at (816) 229-3405, Monday through Friday,

8:00 a.m. to 5:00 p.m. CST.

1.3 REVISION HISTORY

Document Title: SHP Conventional Fire Alarm/Suppression System Product Manual

Document Reorder Number: 06-130

Revision Section Date Reason for Change

0 All Sections 06/12/96 Initial Release

1 All Sections 11/02/99 ULC Additions

2 All Sections 12/01/01 Product Update

3 Section 4.6, 6.3.1 04/02 Added wiring and correct

1.4 TERMS USED IN THIS MANUAL

The following are various terms used in this manual with a brief description of each:

Term Description

Ω

ΩΩ

ΩSymbol for “ohm”. Unit of resistance.

AC Normal State (“AC Normal” Green LED ON) The system is in the AC Normal state when

appropriate AC power is being applied to the system.

Abort An input to a suppression system to prevent an unwanted discharge of fire

suppressant agent. The SHP has several different abort types.

Alarm State (“Alarm” Red LED ON, Piezo pulsing) The alarm occurs when an input circuit

configured for alarm operation has been activated. Activation typically

initiated by a detector or contact device. The system leaves the alarm state

upon entry into the pre-discharge or release state.

firealarmresources.com

PREFACE FIKE CORPORATION

Page 2 of 43 SHP Product Manual UL S2203

Rev. No: 3, 04/02 Manual P/N: 06-130 FM 0Z8A0.AY

Class A wiring Input circuits capable of transmitting an alarm signal during a single open or a

non-simultaneous single ground fault on a circuit conductor shall be

designated as Style D or Class A. Similarly, output circuits capable of

activating during a single open or a non-simultaneous ground fault on a circuit

conductor shall be designated as Style Z or Class A. Commonly referred to

as redundant or 4-wire connection; this manual refers to 4-wire connections

as Class A wiring.

Class B wiring Input circuits incapable of transmitting and alarm signal beyond the location of

the fault condition (listed for Class A wiring above) shall be designated as

Style B or Class B. Similarly, output circuits incapable of operating beyond

the location of the fault condition shall be designated as Style Y or Class B.

This manual refers to 2-wire connections as Class B wiring

Cross-zone Detection A detection scheme where two detectors must activate before the system

enters into the pre-discharge state; at least one detector from each detection

initiating circuit must be active.

Initiating Device A system component that originates transmission of a change-of-state

condition, such as in a smoke detector, manual fire alarm box, or supervisory

switch. This manual interchanges the terms initiating device and input device.

Initiating Device Circuit A circuit to which automatic or manual initiating devices are connected where

the signal received does not identify the individual device operated. This

manual interchanges the terms initiating device circuit and input circuit.

Normal State (“Trouble” Yellow LED OFF) The system is in the normal state when the

power supply and all circuits are configured properly, connected, and

responding properly. The system remains in normal state until a trouble

condition occurs.

Notification Appliance A fire alarm system component such as a bell, horn, speaker, light, or textual

display that provides audible, tactile, or visible output, or any combination

thereof. The device notifies building occupants of system status. This

manual interchanges the terms notification and audible appliance.

Notification Appliance

Circuit

A circuit or path directly connected to a notification appliance(s). This manual

interchanges the terms notification appliance circuit and audible circuit.

Non Power-Limited A circuit designation given for wiring purposes. The amount of current flowing

through the circuit is unlimited vs. being limited, or power-limited. AC power

and Battery wiring is Non Power-limited.

Power-Limited A circuit designation given for wiring purposes. The amount of current flowing

through the circuit is limited (typically by fuse) vs. being unlimited, or non-

power limited. The SHP input and output circuits are power limited. The

circuit has a maximum power that flows through it or it current limits and

opens.

Pre-discharge Delay The time (in seconds) that the system will delay entering the release state

after the zone’s detection type has been satisfied. Activation of an abort

switch will have an effect on this value, depending upon the abort type

selected.

Pre-discharge State (“Alarm” Red LED ON, Piezo chirping) The pre-discharge state occurs when

the zone’s detection type input conditions are satisfied (Cross Zone

Detection, Sequential Alarm Detection, or Single Detector Release). Upon

time delay countdown completion (unless delayed by a pertinent activated

abort input), the system leaves the pre-discharge state and enters the release

state.

Release State (“Alarm” Red LED ON, Piezo chirping) The release state occurs upon

completion of the pre-discharge state or upon activation of a manual release

input. At the start of the release state, output circuits configured for releasing

shall operate.

firealarmresources.com

FIKE CORPORATION PREFACE

UL S2203 SHP Product Manual Page 3 of 43

FM 0Z8A0.AY Manual P/N: 06-130 Rev. No: 3, 04/02

Sequential Detection A detection scheme where the sum total of active detectors on the initiating

circuits must be two or more before the system will enter the pre-discharge

state.

Single Detector Release

Detection

A detection scheme where activation of one detector causes the system to

enter the pre-discharge state. SDR (Single Detector Release) detector(s) are

installed on initiating circuits setup for sequential detection.

Solenoid On Time The time (in minutes) that the solenoid is activated upon entering the release

state. Reset of the system overrides this value.

Supervisory State (“Supervisory” Yellow LED ON, Piezo Warble) The supervisory state occurs

upon activation of a supervisory input circuit. The supervisory state is non-

latching and will follow the status of the supervisory input contact.

Trouble State (“Trouble” Yellow LED ON, Piezo Constant) The trouble state occurs upon

any detectable condition which could impair system operation including

connection problems, ground faults, hardware problems, power problems,

configuration problems, or prematurely activated abort inputs. Certain trouble

conditions are latching; others allow the system to reset upon trouble

condition removal. Depending upon the type of trouble condition, the system

may or may not remain operational. When the system is in trouble state, it is

not in the normal state.

firealarmresources.com

PREFACE FIKE CORPORATION

Page 4 of 43 SHP Product Manual UL S2203

Rev. No: 3, 04/02 Manual P/N: 06-130 FM 0Z8A0.AY

1.5 SYMBOLS USED IN THIS MANUAL

The following symbols are used throughout this manual.

NOTE: Used to call your attention to an important procedure, function or operational

procedure.

CAUTION: Used to identify functions or procedures of utmost importance.

WARNING: Used to identify functions and/or procedures that could cause property damage

or personal injury if the procedures identified in this manual are not followed.

1.6 SAFETY NOTICES

Be certain to read all the following warnings and cautions before installing or using this device.

Accidental damage to the device could result if these warnings and cautions are not heeded!

CAUTION: The SHP contains static sensitive components. Handle the electronics by

the edges only and avoid touching the integrated components. Keep the

electronics in the protective static bags it was shipped in until time for

installation. Always ground yourself with a proper wrist strap before handling

the module(s). If the installer is grounded at all times, damage due to static

discharge will not occur. If the module requires repair or return to Fike, it

must be shipped in an anti-static bag.

CAUTION: To ensure proper system operation after installation of the SHP, this device

must be tested in accordance with NFPA 72 - 1999 edition. Re-acceptance

testing is required after any change, addition or deletion of system

components, or after any modification, repair or adjustment to system

hardware or wiring.

WARNING: Failure to disconnect power to the releasing circuit(s) and disarm the

solenoid(s) or any other "critical operation" contacts prior to system testing

may cause accidental activation of the system.

firealarmresources.com

Tabla de contenidos

Otros manuales de Sistema de seguridad de Fike

Fike

Fike Twinflex V3 Manual de usuario

Fike

Fike 10-11 Series Manual de usuario

Fike

Fike TwinflexPro2 conventional Expansion Card Manual de usuario

Fike

Fike 326-0023 Manual de usuario

Fike

Fike 326-0021 Manual de usuario

Fike

Fike TWINFLEX 313-0021 Manual de usuario

Manuales populares de Sistema de seguridad de otras marcas

Inner Range

Inner Range Concept 2000 Manual de usuario

Climax

Climax Mobile Lite R32 Instrucciones de montaje

CADDX

CADDX NX-6 Manual de usuario

FBII

FBII XL-31 Series Manual de usuario

Johnson Controls

Johnson Controls PENN Connected PC10 Manual de usuario

Aeotec

Aeotec Siren Gen5 Manual de usuario

Blaupunkt

Blaupunkt SA 2700 Manual de usuario

IDEAL

IDEAL Accenta Manual del propietario

AJAX

AJAX DoubleButton Manual de usuario

Swann

Swann SW-P-MC2 Manual de usuario

Ecolink

Ecolink Siren+Chime Manual de usuario

Digital Monitoring Products

Digital Monitoring Products XR150 Manual de usuario

EDM

EDM Solution 6+6 Wireless-AE Manual de usuario

Highway Safety Group

Highway Safety Group EA401 Manual de usuario

Siren

Siren LED GSM Manual de usuario

Detection Systems

Detection Systems 7090i Instrucciones de montaje

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Manual de usuario

Siemens

Siemens FDM273 Manual de usuario