FIBARO FGWP-102 Manual de usuario

Manual de Operaci n

Versi

1.1

CONTENTS

#1: Description and features 3

#2: Basic activation 4

#3: Adding the device 5

#4: Removing the device 6

#5: Operating the device 7

#6: Power and energy consumption 9

#7: Association 10

#8: Z-Wave range test 11

#9: Advanced parameters 12

#10: Specications 19

#11: Regulations 20

FIBARO WALL PLUG

FGWP-102

OPERATING

MANUAL EN

v2.1

Important safety information

Read this manual before attempting to install the device!

Failure to observe recommendations included in this manual

may be dangerous or cause a violation of the law. The manufacturer,

Fibar Group S.A. will not be held responsible for any loss or damage

resulting from not following the instructions of operating manual.

General information about

the FIBARO System

FIBARO is a wireless smart home automation system, based on the

Z-Wave protocol. All of available devices can be controlled through

a computer (PC or Mac), smartphone or tablet. Z-Wave devices are

not only receivers, but can also repeat the signal, increasing the

Z-Wave network’s range. It gives advantage over traditional wireless

systems that require direct link between transmitter and receiver, as

a result the construction of the building could aect network’s range

negatively.

Every Z-Wave network has its unique identication number (home

ID). Multiple independent networks can exist in the building without

interfering. Transmission security of FIBARO System is comparable to

wired systems.

Z-Wave technology is the leading solution in smart home automation.

There is a wide range of Z-Wave devices that are mutually

compatible, independently of manufacturer. It gives the system the

ability to evolve and expand over time. For more information visit:

www.baro.com.

This product is intended for indoor use only in dry locations.

Do not use in damp or wet locations, near a bathtub, sink,

shower, swimming pool, or anywhere else where water or moisture

are present.

DESCRIPTION AND FEATURES

Main features of FIBARO Wall Plug:

• Compatible with any Z-Wave or Z-Wave+ Controller.

• Supports protected mode (Z-Wave network security mode) with

AES-128 encryption.

• Extremely easy installation - simply plug the device into the mains

socket.

• Works as a Z-Wave signal repeater.

• Active power and energy consumption metering.

• Current value of the load and operating mode are indicated by the

multi-colour LED ring.

FIBARO Wall Plug is a universal, Z-Wave Plus compatible, remotely

controlled outlet adapter. This device may be applied wherever you

want to control electrical devices with up to 2500W load.

The Wall Plug is equipped with a power and energy metering

function. It uses a LED ring to visualize the current load with colour

changing illumination and operating mode. This is the smallest and

most attractive device of this type available in the world.

The Wall Plug may be operated using the B-button located on its

casing or via any Z-Wave compatible controller.

#1: Description and features

FIBARO Wall Plug is a fully

compatible Z-Wave PLUS device.

NOTE

This device may be

used with all de-

vices certied with

the Z-Wave Plus cer-

ticate and should be

compatible with such

devices produced by

other manufacturers.

NOTE

FIBARO Wall Plug is

a Security Enabled

Z-Wave Plus product

and a Security Ena-

bled Z-Wave Control-

ler must be used in or-

der to fully utilize the

product.

BASIC ACTIVATION

#2: Basic activation

1. Plug the device into a socket nearby the main Z-Wave controller.

2. Set the main controller in (security/non-security) add mode (see

the controller’s manual).

3. Quickly, triple click the B-button located on the casing.

4. Wait for the device to be added to the system.

5. Successful adding will be conrmed by the controller.

6. Plug a device you want to control into the Wall Plug.

7. Test the device by turning it on and o using the B-Button.

NOTE

When powered, the

device will indicate

Z-Wave status with

colour of LED ring:

• Green - the device is

already added to the

Z-Wave network.

• Red - the device is

not added to any

Z-Wave network.

B-button

NOTE

Socket used for

the Wall Plug should

be easily accessible.

CAUTION

Do not put one

Wall Plug into another.

ADDING THE DEVICE

#3: Adding the device

Adding (Inclusion) - Z-Wave device learning mode, allowing to add

the device to existing Z-Wave network.

To add the device to the Z-Wave network:

1. Plug the device into a socket nearby the main Z-Wave controller.

2. The LED ring will glow red signalling not being added (reset or

remove the device otherwise).

3. Set the main controller in (security/non-security) add mode (see

the controller’s manual).

4. Quickly, triple click the B-button located on the casing.

5. Wait for the adding process to end.

6. Successful adding will be conrmed by the Z-Wave controller’s

message.

NOTE

Adding in security

mode must be per-

formed up to 2 meters

from the controller.

NOTE

In case the device is

not added, please

reset the device and

repeat the adding

procedure.

B-button

REMOVING THE DEVICE

Removing (Exclusion) - Z-Wave device learning mode, allowing to

remove the device from existing Z-Wave network.

To remove the device from the Z-Wave network:

1. Plug the device into a socket nearby the main Z-Wave controller.

2. The LED ring will glow green signalling being added (removing is

not necessary otherwise).

3. Set the main controller into remove mode (see the controller’s

manual).

4. Quickly, triple click the B-button located on the casing.

5. Wait for the removing process to end.

6. Successful removing will be conrmed by the Z-Wave controller’s

message.

NOTE

Removing the Wall Plug

from the Z-Wave net-

work restores all the

default parameters of

the device.

B-button

#4: Removing the device

OPERATING THE DEVICE

#5: Operating the device

Controlling the Wall Plug using the B-button:

Wall Plug is equipped with a B-button, which allows to use the menu

and additionally perform the following actions:

1x click: turn controlled device ON/OFF, conrm selected menu op-

tion (if menu is active)

3x click: add/remove the device to/from a Z-Wave network

Holding: enter/navigate through menu

Visual indications:

The Wall Plug is equipped with a LED ring, signalling sensor’s oper-

ating modes and current active power consumption. In addition the

visual indicator may inform of the Z-Wave network range.

Visual indicator ring signalling modes:

1. By default, when the device is turned ON, the colour will vary de-

pending on the current active power consumption.

2. Once inserted to mains socket the device signals Z-Wave network

inclusion status with blink (green - added, red - not added).

3. Menu position is signalled with assigned illumination colour.

4. Ongoing software update is signalled with cyan blinking.

5. Range of the Z-Wave network with colour depending on type of

communication or the lack of it (only in range tester mode).

Menu allows to perform Z-Wave network actions. In order to use the

menu:

1. Press and hold the B-button.

2. Wait for the device to indicate desired position with a colour:

• GREEN - erase energy consumption memory

• VIOLET - Z-Wave network’s range test

• YELLOW - device reset

3. Release the B-button.

4. Click the B-button to conrm selection.

NOTE

Menu is preceded by

two white ashes of

the LED ring 6 seconds

after the B-button is

pressed.

CAUTION

To avoid risk of electri-

cal shock, do not ope-

rate the device with

wet or moist hands.

OPERATING THE DEVICE

Resetting the device to factory defaults:

Reset procedure allows to restore the device back to its factory set-

tings, which means all information about the Z-Wave controller and

user conguration will be deleted.

1. Make sure the device is powered.

2. Press and hold the B-button.

3. Wait for the LED ring to glow yellow (3rd menu position).

4. Release the B-button.

5. Click the B-button once to conrm selection.

6. After few seconds the device will restart with factory settings,

which is signalled with the red ring colour.

NOTE

Resetting the device is

not the recommend-

ed way of removing

the device from the

Z-Wave network. Use

reset procedure only

if the primary con-

troller is missing or

inoperable. Certain

device removal can

be achieved by the

procedure of remov-

ing described in “Add-

ing the device” on

page 5.

Controlling the Wall Plug with FIBARO Home Center controller:

The Wall Plug after successful adding is represented in the

Home Center interface with a single icon. It allows to turn on and o

the device and displays current active power and cumulative energy

consumption.

Disabling visual indicator:

Visual indication ring may be turned o for status signalling (turned

ON/OFF, power consumption). That means each status change will

be signalled by a short white blink of the ring. Disabling it will not

change operation of the device. To disable the LED ring:

1. Insert the Wall Plug in a socket.

2. Press and hold the B-button for about 3 seconds.

3. Release the B-button after LED ring starts pulsing white.

To restore visual indications perform above procedure again.

NOTE

Disabling the LED ring

indications will also

aect alarm signaliza-

tion.

POWER AND ENERGY CONSUMPTION

#6: Power and energy

consumption

The Wall Plug allows to monitor the active power and energy con-

sumption. Data is sent to the main Z-Wave controller, e.g. Home

Center. Measuring is carried out by the most advanced micro-con-

troller technology, assuring maximum accuracy and precision.

Electric active power - power that energy receiver is changing into a

work or a heat. The unit of active power is Watt [W].

Electric energy - energy consumed by a device through a time

period. Consumers of electricity in households are billed by sup-

pliers on the basis of active power used in given unit of time. Most

commonly measured in kilowatt-hour [kWh]. One kilowatt-hour is

equal to one kilowatt of power consumed over period of one hour,

1kWh = 1000Wh.

Resetting consumption memory:

Wall Plug allows to erase stored consumption data (turning it o/on

or removing it from the socket will not erase consumption):

1. Make sure the device is powered.

2. Press and hold the B-button.

3. Release the B-button when the LED ring glows green (1st menu

position).

4. Press the B-button briey.

Otros manuales para FGWP-102

Tabla de contenidos

Otros manuales de Accesorios de FIBARO

FIBARO

FIBARO FGBHFS-001 Manual de usuario

FIBARO

FIBARO FGBHDW-002 Manual de usuario

FIBARO

FIBARO FGMS-001 Manual de usuario

FIBARO

FIBARO FGWOE-011 Manual de usuario

FIBARO

FIBARO FGFS-101-ZW5 Manual de usuario

FIBARO

FIBARO Walli Outlet E Manual de usuario

FIBARO

FIBARO FGWPG-111 Manual de usuario

FIBARO

FIBARO FGMS-001-USA-A-V1.01 Manual de usuario

FIBARO

FIBARO FGBHFS-101 Manual de usuario

FIBARO

FIBARO FGBHDW-002 Manual de usuario

FIBARO

FIBARO FGDW-002 Manual de usuario

FIBARO

FIBARO Flood Sensor Manual de usuario

FIBARO

FIBARO FGBHMS-001 Guía de instalación

FIBARO

FIBARO FGBHDW-002 Manual de usuario

FIBARO

FIBARO FGFS-101 Manual de usuario

FIBARO

FIBARO CO Sensor FGCD-001 Manual de usuario

FIBARO

FIBARO FGK-101 Manual de usuario

FIBARO

FIBARO FGWPA-111 Manual de usuario

FIBARO

FIBARO FGFS-101 Manual de usuario

FIBARO

FIBARO FGWPB-121 Manual de usuario

FIBARO

FIBARO FGMS-001 Manual de usuario

FIBARO

FIBARO FGFS-101 Manual de usuario

FIBARO

FIBARO FGFS-101-EN-A Manual de usuario

FIBARO

FIBARO FGWPG-111 Manual de usuario

Manuales populares de Accesorios de otras marcas

Hillco

Hillco 2810 Manual de usuario

Siemens

Siemens QSA2700D Manual del operador

Contours

Contours ZY024 Manual de usuario

Saivod

Saivod VS621 Manual de usuario

Virtuox

Virtuox VirtuCLEAN 2.0 Manual de usuario

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manual de usuario

Z-Wave

Z-Wave HSD-200Z Manual de usuario

turck

turck FMX-IM-2UPLI63FX Manual de usuario

Decagon Devices

Decagon Devices 10HS Manual de usuario

UPPAbaby

UPPAbaby Cup Holder Manual de usuario

Elko

Elko SmartSensor Leakage Wireless Manual de usuario

Grizzly

Grizzly H8371 Manual de usuario

Panasonic

Panasonic HG-T Series Manual de usuario

IFM Electronic

IFM Electronic Efector 250 Series Guía de referencia

DigiDesign

DigiDesign 888/24 I/O Manual de usuario

PROZIS

PROZIS QUAY Manual de usuario

patagonia

patagonia PSI Vest Manual de usuario

SFC Energy

SFC Energy EFOY GO! Manual de usuario