FIBARO FGK-10x Manual de usuario

FIBARO DOOR/WINDOW SENSOR

FGK-10x

CONTENTS

#1: Description and features 4

#2: Basic activation 5

#3: Adding/removing the device 6

#4: Temperature sensor 7

#5: Button or external sensor 8

#6: Physical installation 9

#7: Operating the device 10

#8: Association 12

#9: Advanced parameters 13

#10: Specications 19

#11: Regulations 20

OPERATING

MANUAL EN

v2.0

Important safety information

Read this manual before attempting to install the device!

Failure to observe recommendations included in this manual

may be dangerous or cause a violation of the law. The manufacturer,

Fibar Group S.A. will not be held responsible for any loss or damage

resulting from not following the instructions of operating manual.

General information about

the FIBARO System

FIBARO is a wireless smart home automation system, based on the

Z-Wave protocol. All of available devices can be controlled through

a computer (PC or Mac), smartphone or tablet. Z-Wave devices are

not only receivers, but can also repeat the signal, increasing the

Z-Wave network’s range. It gives advantage over traditional wireless

systems that require direct link between transmitter and receiver, as

a result the construction of the building could aect network’s range

negatively.

Every Z-Wave network has its unique identication number (home

ID). Multiple independent networks can exist in the building without

interfering. Transmission security of FIBARO System is comparable to

wired systems.

Z-Wave technology is the leading solution in smart home automation.

There is a wide range of Z-Wave devices that are mutually

compatible, independently of manufacturer. It gives the system the

ability to evolve and expand over time. For more information visit:

www.baro.com.

DESCRIPTION AND FEATURES

Main features of FIBARO Door/Window Sensor:

• Compatible with any Z-Wave or Z-Wave+ Controller,

• Supports protected mode (Z-Wave network security mode) with

AES-128 encryption,

• Door/window opening detected through separation of Sensor’s

body and a magnet,

• Easily mounted on doors, windows, garage gates and roller blinds,

• Battery powered,

• Visual LED indicator signalling status of the device,

• Compatible with the DS18B20 temperature sensor,

• Potential-free input allowing to connect a button or binary sensor.

FIBARO Door/Window Sensor is a wireless, battery powered reed

sensor compatible with the Z-Wave standard. Changing the device’s

status will automatically send signal to the Z-Wave controller and

associated devices.

Sensor can be used to trigger scenes and everywhere there is a need

for information about opening or closing of doors, windows, garage

doors, etc. Opening is detected by separating the sensor’s body and

the magnet.

In addition the FIBARO Door/Window Sensor supports one DS18B20

temperature sensor and has one potential free input.

#1: Description and features

FIBARO Door/Window Sensor is

a fully compatible Z-Wave PLUS

device.

NOTE

This device may be

used with all devices

certied with Z-Wave

Plus certicate and

should be compatible

with such devices pro-

duced by other manu-

facturers.

NOTE

FIBARO Door/Window

Sensor is a Security

Enabled Z-Wave Plus

product and a Secu-

rity Enabled Z-Wave

Controller must be

used in order to fully

utilize the product.

BASIC ACTIVATION

#2: Basic activation

1. Open the cover.

2. Remove the battery blocker.

3. Close the cover.

4. Add the device (see “Adding/removing the device” on page 6).

5. Install the device (see “Physical installation” on page 9).

NOTE

The antenna should

be placed above the

battery. Never cut,

shorten or bend the

antenna. Its length is

suited to the band at

which the system op-

erates.

NOTE

Metal surfaces in close

vicinity (e.g. metal

switch boxes, metal

door trims) may im-

pair the reception ca-

pability.

ADDING/REMOVING THE DEVICE

#3: Adding/removing the device

Adding (Inclusion) - Z-Wave device learning mode, allowing to add

the device to existing Z-Wave network.

To add the device to the Z-Wave network:

1. Close the cover.

2. Place the Door/Window Sensor within the direct range of your

Z-Wave controller.

3. Set the main controller into (security/non-security) add mode (see

the controller’s manual).

4. Quickly, three times press the TMP button.

5. Wait for the adding process to end.

6. Successful adding will be conrmed by the Z-Wave controller’s

message.

Removing (Exclusion) - Z-Wave device learning mode, allowing to

remove the device from existing Z-Wave network.

To remove the device from the Z-Wave network:

1. Close the cover.

2. Place the Door/Window Sensor within the direct range of your

Z-Wave controller.

3. Set the main controller into remove mode (see the controller’s

manual).

4. Quickly, three times press the TMP button.

5. Wait for the removing process to end.

6. Successful removing will be conrmed by the Z-Wave controller’s

message.

TMP

button

NOTE

Adding in security

mode must be per-

formed up to 2 meters

from the controller.

NOTE

Removing the device

from the Z-Wave net-

work restores all the

default parameters of

the device (except for

parameter 20).

NOTE

In case the device is

not added, please re-

set the device and re-

peat the adding pro-

cedure.

TMP

button

TEMPERATURE SENSOR

#4: Temperature sensor

CAUTION

Connected the device

in accordance with

the wiring diagram.

Incorrect wiring may

be dangerous or result

in the device break-

down.

NOTE

Connecting/discon-

necting the temper-

ature sensor to/from

previously added

Door/Window Sensor,

requires removing

and re-adding the

device to the Z-Wave

network.

The DS18B20 temperature sensor may be installed anywhere where

temperature readouts are necessary. If adequately protected, the

DS18B20 sensor may be installed in humid conditions, under water,

sealed in concrete or placed under the oor.

CAUTION

Connecting devic-

es and sensors other

than DS18B20 is not

allowed.

To activate the device with temperature measurement functionality:

1. Open the cover.

2. Connect the temperature sensor to terminals of the device

according to the diagram:

3. Add the device (see “Adding/removing the device” on page 6).

4. Install the device (see “Physical installation” on page 9).

GND

max 30m

TD (DQ)

TP (VDQ)

321

(BOTTOM VIEW)

(TOP VIEW)

TMP

DS18B20

123

321

GND

TD (DQ)

TP (VDQ)

DS18B20

(TEMP_POWER) - power supply terminal of

temperature sensor

(TEMP_DATA) - signal terminal of temperature sensor

GND

(GROUND) - ground terminal

BUTTON OR EXTERNAL SENSOR

#5: Button or external sensor

Door/Window Sensor is equipped with a potential-free input. It allows

to change device state using the external button or sensor through

GND signal.

If the Door/Window Sensor will be used only as a binary sensor, do

not install the magnet.

To activate the device as a binary sensor:

1. Open the cover.

2. Connect the button or external sensor to terminals of the device

according to diagram:

3. Add the device (see “Adding/removing the device” on page 6) if

the device is not already added.

4. In case of connecting external sensor modify advanced parameter

no. 20 to match type of the sensor, then remove and re-add the

device to the network.

5. Install the device (see “Physical installation” on page 9).

GND

MOMENTARY SWITCH

(TOP VIEW)

TMP

GND

(GROUND) - ground terminal

- potential-free input

NOTE

Potential-free input is

a type of input contact

which does not have

a voltage on it after

closing.

CAUTION

Connected the device

in accordance with

the wiring diagram.

Incorrect wiring may

be dangerous or result

in the device break-

down.

PHYSICAL INSTALLATION

#6: Physical installation

To install the Door/Window Sensor:

1. Stick the included self-adhesive pads to the bottom of the device

and magnet.

2. Peel o the protective layer of the sticker.

3. Stick the device onto the door/window frame.

4. Stick the magnet onto the moving part of the door/window, no

further than 5mm from the sensor.

max. 5 mm

Correct postioning of the magnet in relation to the Sensor:

Positioning of the Sensor and the magnet:

OPERATING THE DEVICE

#7: Operating the device

Controlling the Door/Window Sensor with FIBARO Home Center

controller:

After adding the Sensor to the FIBARO System, it will be represented

by one or two icons in Home Center interface.

Sensor without connected DS18B20 sensor or used with a button

connected to IN input (without magnet), will be represented by a sin-

gle icon.

In case of connecting DS18B20 temperature sensor, the additional

temperature sensor icon will be displayed.

Tamper (TMP) button:

The Door/Window Sensor is equipped with a tamper switch with two

buttons.

First TMP button is located inside the device, pressed by the closed

cover. Second TMP button is located at bottom of the device, pressed

by the surface on which the device is mounted.

For the tamper switch to work one of the buttons must always be

pressed!

When one of the buttons is released, the tamper alarm will be send to

the controller and associated devices.

Additionally, tamper button allows to control the device directly.

TMP

(TOP VIEW)

(BOTTOM VIEW) TMP

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Accesorios de FIBARO

FIBARO

FIBARO FGWPG-111 Manual de usuario

FIBARO

FIBARO CO Sensor FGCD-001 Manual de usuario

FIBARO

FIBARO FGFS-001 Manual de usuario

FIBARO

FIBARO FGBHDW-002 Manual de usuario

FIBARO

FIBARO FGWPG-111 Manual de usuario

FIBARO

FIBARO FGSS-001-EN-A-v1.00 Manual de usuario

FIBARO

FIBARO FIBEFGMS-001-ZW5 Manual de usuario

FIBARO

FIBARO FGFS-101 Manual de usuario

FIBARO

FIBARO FGWPA-111 Manual de usuario

FIBARO

FIBARO FGMS-001 Manual de usuario

FIBARO

FIBARO Flood Sensor Manual de usuario

FIBARO

FIBARO FGFS-101 Manual de usuario

FIBARO

FIBARO FGFS-101 Manual de usuario

FIBARO

FIBARO FGBHFS-001 Manual de usuario

FIBARO

FIBARO FGBHFS-101 Manual de usuario

FIBARO

FIBARO FGWOE-011 Manual de usuario

FIBARO

FIBARO FGFS-101-ZW5 Manual de usuario

FIBARO

FIBARO Flood Sensor Manual de usuario

FIBARO

FIBARO FGMS-001-USA-A-V1.01 Manual de usuario

FIBARO

FIBARO FGK Series Manual de usuario

FIBARO

FIBARO Walli Outlet E Manual de usuario

FIBARO

FIBARO FGBHDW-002 Manual de usuario

FIBARO

FIBARO FGBHDW-002 Manual de usuario

FIBARO

FIBARO FGWPB-121 Manual de usuario

Manuales populares de Accesorios de otras marcas

Hillco

Hillco 2810 Manual de usuario

Siemens

Siemens QSA2700D Manual del operador

Contours

Contours ZY024 Manual de usuario

Saivod

Saivod VS621 Manual de usuario

Virtuox

Virtuox VirtuCLEAN 2.0 Manual de usuario

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manual de usuario

Z-Wave

Z-Wave HSD-200Z Manual de usuario

turck

turck FMX-IM-2UPLI63FX Manual de usuario

Decagon Devices

Decagon Devices 10HS Manual de usuario

UPPAbaby

UPPAbaby Cup Holder Manual de usuario

Elko

Elko SmartSensor Leakage Wireless Manual de usuario

Grizzly

Grizzly H8371 Manual de usuario

Panasonic

Panasonic HG-T Series Manual de usuario

IFM Electronic

IFM Electronic Efector 250 Series Guía de referencia

DigiDesign

DigiDesign 888/24 I/O Manual de usuario

PROZIS

PROZIS QUAY Manual de usuario

patagonia

patagonia PSI Vest Manual de usuario

SFC Energy

SFC Energy EFOY GO! Manual de usuario