Feig Electronic OBID i-scan Instrucciones de instalación y funcionamiento

APPLICATION-NOTE

preliminary

public (B)

2008-06-17

N61100-2e-ID-B.doc

OBI

i-scan

Smartshelf Demo

OBID i-scan®Application-Note Smartshelf Demo

FEIG ELECTRONIC GmbH Page 2 of 17 N61100-2e-ID-B.doc

Note

FEIG ELECTRONIC GmbH

Lange Straße 4

D-35781 Weilburg

Tel.: +49 6471 3109-0

http://www.feig.de

With the edition of this document, all previous editions become void. Indications made in this manual may be

changed without previous notice.

Copying of this document, and giving it to others and the use or communication of the contents thereof are

forbidden without express authority. Offenders are liable to the payment of damages. All rights are reserved

in the event of the grant of a patent or the registration of a utility model or design.

Composition of the information in this document has been done to the best of our knowledge. FEIG

ELECTRONIC GmbH does not guarantee the correctness and completeness of the details given in this

manual and may not be held liable for damages ensuing from incorrect or incomplete information. Since,

despite all our efforts, errors may not be completely avoided, we are always grateful for your useful tips.

The instructions given in this manual are based on advantageous boundary conditions. FEIG ELECTRONIC

GmbH does not give any guarantee promise for perfect function in cross environments and does not give

any guaranty for the functionality of the complete system which incorporates the subject of this document.

FEIG ELECTRONIC call explicit attention that devices which are subject of this document are not designed

with components and testing methods for a level of reliability suitable for use in or in connection with surgical

implants or as critical components in any life support systems whose failure to perform can reasonably be

expected to cause significant injury to a human. To avoid damage, injury, or death, the user or application

designer must take reasonably prudent steps to protect against system failures.

FEIG ELECTRONIC GmbH assumes no responsibility for the use of any information contained in this docu-

ment and makes no representation that they free of patent infringement. FEIG ELECTRONIC GmbH does

not convey any license under its patent rights nor the rights of others.

OBID®and OBID i-scan®are registered trademarks of FEIG ELECTRONIC GmbH.

I-CODE®is a registered trademark of Philips Electronics N.V.

Tag-itTM is a registered trademark of Texas Instruments Incorporated.

Microsoft®and Windows®are registered trademarks of Microsoft Corporation

Linux is a registered trademark of Linus Torvalds.

OBID i-scan®Application-Note Smartshelf Demo

FEIG ELECTRONIC GmbH Page 3 of 17 N61100-2e-ID-B.doc

General information's regarding this document

•The sign ")" indicates extensions or changes of this manual compared with the former issue.

•If bits within one byte are filled with "-", these bit spaces are reserved for future extensions or

for internal testing- and manufacturing-functions. These bit spaces must not be changed, as this

may cause faulty operation of the reader.

•The following figure formats are used:

0...9: for decimal figures

0x00...0xFF: for hexadecimal figures,

b0...1 for binary figures.

•The hexadecimal value in brackets "[ ]" marks a control byte (command).

OBID i-scan®Application-Note Smartshelf Demo

FEIG ELECTRONIC GmbH Page 4 of 17 N61100-2e-ID-B.doc

Content

1. Safety Instructions / Warning - Read before start-up ! 5

2. Introduction 6

3. System Requirements 7

3.1.1 Smartshelf (Embedded Linux) HF.....................................................................................7

3.1.2 Smartshelf (Embedded Linux) UHF..................................................................................7

3.2 SmartShelfDemo (Windows XP/2000) .................................................................................7

3. Installation 8

4. Settings 9

4.1 ISC.ANT.MUX / ISC.ANT.UMUX Configuration ...................................................................9

4.2 SmartShelfDemo ...................................................................................................................9

4.3.1 Antenna organisation HF-Reader...................................................................................11

4.3.2 Antenna organisation UHF-Reader.................................................................................13

4.3.3 Antenna numeration ........................................................................................................14

5 Connection Information 15

APPENDIX: XML conventions 16

OBID i-scan®Application-Note Smartshelf Demo

FEIG ELECTRONIC GmbH Page 5 of 17 N61100-2e-ID-B.doc

1. Safety Instructions / Warning - Read before start-up !

•The device may only be used for the intended purpose designed by for the manufacturer.

•The operation manual should be conveniently kept available at all times for each user.

•Unauthorized changes and the use of spare parts and additional devices which have not been

sold or recommended by the manufacturer may cause fire, electric shocks or injuries. Such

unauthorized measures shall exclude any liability by the manufacturer.

•The liability-prescriptions of the manufacturer in the issue valid at the time of purchase are valid

for the device. The manufacturer shall not be held legally responsible for inaccuracies, errors,

or omissions in the manual or automatically set parameters for a device or for an incorrect

application of a device.

•Repairs may only be executed by the manufacturer.

•Installation, operation, and maintenance procedures should only be carried out by qualified

personnel.

•Use of the device and its installation must be in accordance with national legal requirements

and local electrical codes .

•When working on devices the valid safety regulations must be observed.

•Special advice for carriers of cardiac pacemakers:

Although this device doesn't exceed the valid limits for electromagnetic fields you should keep

a minimum distance of 25 cm between the device and your cardiac pacemaker and not stay in

an immediate proximity of the device respective the antenna for some time.

OBID i-scan®Application-Note Smartshelf Demo

FEIG ELECTRONIC GmbH Page 6 of 17 N61100-2e-ID-B.doc

2. Introduction

The software package Smartshelf Demo consists of two programs.

The first program is called Smartshelf. This program is an executable binary file for the i-scan

Readers ID ISC.LR2000 and ID ISC.LRU2000.

This program was developed as an example for registering and managing the current stock of a

warehouse. For instance an possible application is to check the availability of a product, or the

availability of books in a library.

With this program it is possible to use up to 512 antennas with max. 73 multiplexers of type ID

ISC.ANT.MUX for Reader ID ISC.LR2000 or ID ISC.ANT.UMUX for Reader ID ISC.LRU2000.

The program makes inventory commands and if there is a transponder in field it inserts this trans-

ponder with its attributes into a taglist. Furthermore there is a notification function implemented

which generates status messages if a transponder is detected or lost. The application then sends a

message to the client side Windows program called SmartShelfDemo, which is the second pro-

gram. SmartShelfDemo let’s you also change reader settings, i.e. the number of antennas and the

threshold.

The number of antennas value is (obviously) how many antennas are connected. You need to set

the number of antennas only if you use the HF-Reader ID ISC.LR2000, because it can not detect

antennas automatically. Threshold means how often a transponder could not respond until it will be

deleted from the taglist (the reader will then send a “LOST” notification). There is even a possibility

to connect FEIG’s demo application ISOSTART to change the configuration of the reader. In this

case the protocols are forwarded to the reader and the received protocols are returned to

ISOSTART.

With the SmartshelfDemo program it is possible to show the complete contents of the taglist from

the embedded program Smartshelf. Event messages are received when there is a new trans-

ponder in field or a transponder was lost. The messages are sent as standard XML documents.

OBID i-scan®Application-Note Smartshelf Demo

FEIG ELECTRONIC GmbH Page 7 of 17 N61100-2e-ID-B.doc

3. System Requirements

3.1.1 Smartshelf (Embedded Linux) HF

•Reader ID ISC.LR2000 with ACC

•ACC Firmware V1.09.00

•ID ISC.ANT.MUX Rev. FE 553/3 with Firmware V1.05

•Ethernet connection

3.1.2 Smartshelf (Embedded Linux) UHF

•Reader ID ISC.LRU2000 with ACC

•ACC Firmware V1.09.00

•ID ISC.ANT.UMUX Rev. FE 623/1 with Firmware V00.11.00 or higher

•Ethernet connection

3.2 SmartShelfDemo (Windows XP/2000)

•Windows 2000/XP

•Ethernet connection

OBID i-scan®Application-Note Smartshelf Demo

FEIG ELECTRONIC GmbH Page 8 of 17 N61100-2e-ID-B.doc

3. Installation

The embedded Smartshelf function is realized inside the Application Connectivity Controller

(ACC) of the reader. Thus, only the ACC must be updated with the firmware version 1.09.00. This

can be done with the OBIDFirmwareUpdateTool and it is recommended to use the ethernet con-

nection.

After the firmware update, the ACC reboots and the Smartshelf application is started 5 seconds

later. The green LED V6 signals a running ACC, the orange LED V3 signals communication ac-

tions between ACC and RFC and the blue LED V2 signals RF communication with tags.

The Smartshelf function is initialized for 3 antennas. This can be changed with the Windows appli-

cation SmartShelfDemo. For all other settings use ISOStart.

The Windows application SmartShelfDemo consists of three files (SmartShelfDemo.exe, Smart-

ShelfDemo.ini and FETCP.DLL) and can be copied to any directory of the target PC.

OBID i-scan®Application-Note Smartshelf Demo

FEIG ELECTRONIC GmbH Page 9 of 17 N61100-2e-ID-B.doc

4. Settings

4.1 ISC.ANT.MUX / ISC.ANT.UMUX Configuration

For detailed information see M30201-xde-ID-B.doc for ID ISC.ANT.MUX or M71100-xde-ID-B.doc

for ID ISC.ANT.UMUX

4.2 SmartShelfDemo

After the first start of the program some settings for the smartshelf reader must be executed. Press

the button ‘Settings...’ and open the settings dialog. With this dialog, the smartshelf reader can be

configured.

After configuring, the handling of smartshelf notifications are enabled with the button ‘Start’.

OBID i-scan®Application-Note Smartshelf Demo

FEIG ELECTRONIC GmbH Page 10 of 17 N61100-2e-ID-B.doc

•Threshold must be a value between 0...255. The threshold is for lost notifications. A 5 means,

that a tag is five times re-read after absent until a lost notification is sent. The re-read is real-

ized with a Read Multiple Blocks command and costs approximately 30ms.

•No. of antennas must be a value between 1...512. The no. of antennas is needed only if the

HF-Reader ID ISC.LR2000 is used. The combination of UHF-Reader ID ISC.LRU2000 and ID

ISC.ANT.UMUX multiplexers can detect multiplexers and connected antennas automatically.

•IP is the IP address of the reader. The addressed port is set to 10005, because it is fix.

•The button ‘Set reader configuration’ establish a connection to the reader, transfers the pa-

rameters and close the connection. The reader saves the parameters in its EEPROM and re-

boots, if the number of antenna is changed. When only the lost threshold is changed, then no

reboot is executed.

By pressing the button „Get List“ all transponders which are currently in field will be displayed.

Tabla de contenidos

Otros manuales de Sistema RFID de Feig Electronic

Feig Electronic

Feig Electronic OBID i-scan HF ID ISC.ANT1300/680-GPC Manual de usuario

Feig Electronic

Feig Electronic ID ISC.ANT1710/690 Crystal Gate Excellence... Manual de usuario

Feig Electronic

Feig Electronic OBID classic-pro ID CPR.02.10-AD Manual de usuario

Feig Electronic

Feig Electronic ID ISC.LRU3500 Manual de usuario

Feig Electronic

Feig Electronic ID ISC.ANT.U500/270 Manual de usuario

Feig Electronic

Feig Electronic OBID ID ISC.ANT40/30 Manual de usuario

Feig Electronic

Feig Electronic OBID i-scan UHF ID ISC.MRU102-PoE-LED Manual de usuario

Feig Electronic

Feig Electronic OBID i-scan ID ISC.MRU200i Manual de usuario

Feig Electronic

Feig Electronic ID ISC.ANT.U500/270-DM Manual de usuario

Feig Electronic

Feig Electronic OBID classic-pro ID CPR.03.20-CD Manual de usuario

Feig Electronic

Feig Electronic ID LR5400 Manual de usuario

Feig Electronic

Feig Electronic ID ISC.PRH101-A Manual de usuario

Feig Electronic

Feig Electronic OBID classic-pro ID CPR40.30-A Manual de usuario

Feig Electronic

Feig Electronic ID CPR40.30-U Manual de usuario

Feig Electronic

Feig Electronic ID LRU500i-BD Series Manual de usuario

Feig Electronic

Feig Electronic OBID i-scan ID ISC.MR101-USB Manual de usuario

Feig Electronic

Feig Electronic ID RED.M50-E Manual de usuario

Feig Electronic

Feig Electronic OBID i-scan ID ISC.MR101-USB Manual de usuario

Feig Electronic

Feig Electronic OBID i-scan ID ISC.ANT.MUX Manual de usuario

Feig Electronic

Feig Electronic ID HyWEAR compact Manual de usuario

Feig Electronic

Feig Electronic OBID ID RW40.30-USB Manual de usuario

Feig Electronic

Feig Electronic OBID classic-pro ID CPR.04.P/AB-USB Manual de usuario

Feig Electronic

Feig Electronic ID ISC.MRMU102-A Manual de usuario

Feig Electronic

Feig Electronic OBID i-scan ID ISC.LRM2500-A Manual de usuario

Manuales populares de Sistema RFID de otras marcas

Chainway

Chainway R1 Manual de usuario

IFM

IFM DTC600 Manual de usuario

Elatec

Elatec TWN4 MULTITECH NANO LEGIC 63 M Manual de usuario

RHOMBUS

RHOMBUS DR20 Manual de usuario

Sirit

Sirit IDentity 6204 Manual de usuario

SOREX

SOREX FLEX Manual de usuario

Omron

Omron V780-HMD68-EIP-KR Manual de usuario

IDENTEC SOLUTIONS

IDENTEC SOLUTIONS iPOINT Si Instrucciones de uso

Shuttle

Shuttle BR06 Instrucciones de uso

Digilock

Digilock Curve Keypad Basic Manual de usuario

Atid

Atid AT870 Manual de usuario

Chacon

Chacon 34958 Manual de usuario

Paxton

Paxton PROXIMITY architectural reader Manual de usuario

CipherLab

CipherLab 1800 series Manual de usuario

Brady

Brady FR22 Manual de usuario

Kronotech

Kronotech BLUEBOX GEN2 M30 UHF Manual de usuario

Unitech

Unitech RH767 Manual de usuario

Honeywell

Honeywell 026366.00 Manual de usuario