Feig Electronic ID ISC.MR102 Manual de usuario

MANUAL

final –public (B)

2018-07-24 –H01113-4e-ID-B.docx

ID ISC.MR102

Standard Reader

from Firmware-Version 2.10 or higher

Identification

Manual

ID ISC.MR102

FEIG ELECTRONIC GmbH

Page 2 of 153

H01113-4e-ID-B.docx

Note

FEIG ELECTRONIC GmbH

Lange Strasse 4

D-35781 Weilburg-Waldhausen

Tel.: +49 6471 3109-0

http://www.feig.de

With the edition of this document, all previous editions become void. Indications made in this manual may be

changed without previous notice.

Copying of this document, and giving it to others and the use or communication of the contents thereof are

forbidden without express authority. Offenders are liable to the payment of damages. All rights are reserved

in the event of the grant of a patent or the registration of a utility model or design.

Composition of the information in this document has been done to the best of our knowledge. FEIG

ELECTRONIC GmbH does not guarantee the correctness and completeness of the details given in this

manual and may not be held liable for damages ensuing from incorrect or incomplete information. Since,

despite all our efforts, errors may not be completely avoided, we are always grateful for your useful tips.

The instructions given in this manual are based on advantageous boundary conditions. FEIG ELECTRONIC

GmbH does not give any guarantee promise for perfect function in cross environments and does not give

any guaranty for the functionality of the complete system which incorporates the subject of this document.

FEIG ELECTRONIC call explicit attention that devices which are subject of this document are not designed

with components and testing methods for a level of reliability suitable for use in or in connection with surgical

implants or as critical components in any life support systems whose failure to perform can reasonably be

expected to cause significant injury to a human. To avoid damage, injury, or death, the user or application

designer must take reasonably prudent steps to protect against system failures.

FEIG ELECTRONIC GmbH assumes no responsibility for the use of any information contained in this docu-

ment and makes no representation that they free of patent infringement. FEIG ELECTRONIC GmbH does

not convey any license under its patent rights nor the rights of others.

I-CODE®is a registered trademark of Philips Electronics N.V.

Tag-itTM is a registered trademark of Texas Instruments Incorporated.

Identification

Manual

ID ISC.MR102

FEIG ELECTRONIC GmbH

Page 3 of 153

H01113-4e-ID-B.docx

General information's regarding this document

If bits within one byte are filled with "-", these bit spaces are reserved for future extensions or

for internal testing- and manufacturing-functions. These bit spaces must not be changed, as this

may cause faulty operation of the reader.

The following figure formats are used:

0...9: for decimal figures

0x00...0xFF: for hexadecimal figures,

b0...1 for binary figures.

The hexadecimal value in brackets "[ ]" marks a control byte (command).

Identification

Manual

ID ISC.MR102

FEIG ELECTRONIC GmbH

Page 4 of 153

H01113-4e-ID-B.docx

Contents

ID ISC.MR102 1

Standard Reader 1

1. Safety Instructions / Warning - Read before start-up ! 8

Revision History of documentation ........................................................................................9

Abbreviations ......................................................................................................................... 10

2. Data Transmission between OBID i-scan®ID ISC.MR102 and Host 11

2.1. Configuration Commands and Control Commands...................................................... 11

2.2. ISO15693 Host Commands............................................................................................. 12

2.3. Scan Mode ....................................................................................................................... 15

3. Interface 17

3.1. Protocol Frames of TCP/IP protocol ..............................................................................17

3.2. Serial Data Format and Protocol Frames....................................................................... 18

3.3. CRC16 Calculation Algorithm.........................................................................................20

4. Configuration Parameters (CFG) 21

4.1. CFG0: Passwords............................................................................................................ 23

4.2. CFG1: Interface................................................................................................................ 25

4.3. CFG2: Inputs / Outputs general...................................................................................... 29

4.4. CFG3: RF-Interface..........................................................................................................32

4.5. CFG4: Transponder Parameters.....................................................................................34

4.6. CFG5: Anticollision .........................................................................................................37

4.7. CFG6: Customer Command Option Bytes..................................................................... 38

4.8. CFG7 - 10: Reserved .......................................................................................................39

4.9. CFG11 Read Mode Data.................................................................................................. 40

4.10. CFG12: Read Mode - Filter............................................................................................ 44

4.11. CFG13 Scan Mode.........................................................................................................45

4.12. CFG14-15: Reserved......................................................................................................48

4.13. CFG16: Persistence Reset............................................................................................ 49

Identification

Manual

ID ISC.MR102

FEIG ELECTRONIC GmbH

Page 5 of 153

H01113-4e-ID-B.docx

4.14. CFG17-19: Reserved......................................................................................................50

4.15. CFG20: RF-Parameter ...................................................................................................51

4.16. CFG21: Reserved........................................................................................................... 52

4.17. CFG22-23: Selection mask for ISO18000-3M3............................................................. 53

4.18. CFG24-32: Reserved......................................................................................................56

4.19. CFG33-34: LAN-Hostname............................................................................................ 57

4.20. CFG35-39: Reserved......................................................................................................58

4.21. CFG40: LAN Settings, Part 1 (only for MR102-PoE, SPAD102-E).............................. 59

4.22. CFG41: LAN Settings, Part 2 (only for MR102-PoE, SPAD102-E).............................. 60

4.23. CFG49: Notification Channel (only for MR102-PoE, SPAD102-E) .............................62

4.24. CFG63: Customer Parameter........................................................................................ 64

5. Protocols for Reader Configuration 65

5.1. [0x80] Read Configuration..............................................................................................65

5.2. [0x81] Write Configuration..............................................................................................66

5.3. [0x83] Set Default Configuration (Reset) .......................................................................67

6. Protocols for Reader Control 68

6.1. [0x52] Baud Rate Detection ............................................................................................68

6.2. [0x55] Start Flash Loader................................................................................................ 68

6.3. [0x63] Software Reset ..................................................................................................... 69

6.4. [0x64] System Reset........................................................................................................ 69

6.5. [0x65] Get Software Version...........................................................................................70

6.6. [0x66] Get Reader Info.....................................................................................................72

6.7. [0x69] RF Reset................................................................................................................ 74

6.8. [0x6A] RF ON/OFF........................................................................................................... 74

6.9. [0x6D] Get Noise Level.................................................................................................... 75

6.10. [0x6E] Reader Diagnostic ............................................................................................. 76

6.11. [0x72] Set Output...........................................................................................................78

6.12. [0x85] Set System Timer ............................................................................................... 80

6.13. [0x86] Get System Timer...............................................................................................80

6.14. [0xA0] Reader-Login......................................................................................................81

7. Protocols for ISO15693 Host Commands 82

Identification

Manual

ID ISC.MR102

FEIG ELECTRONIC GmbH

Page 6 of 153

H01113-4e-ID-B.docx

7.1. [0xB0] Host commands for ISO15693 Mandatory and Optional Commands...............83

7.1.1. [0x01] Inventory .........................................................................................................84

7.1.2. [0x02] Stay Quiet .......................................................................................................86

7.1.3. [0x22] Lock Multiple Blocks........................................................................................87

7.1.4. [0x23] Read Multiple Blocks....................................................................................... 89

7.1.5. [0x24] Write Multiple Blocks....................................................................................... 92

7.1.6. [0x25] Select..............................................................................................................95

7.1.7. [0x26] Reset to Ready................................................................................................96

7.1.8. [0x27] Write AFI.........................................................................................................97

7.1.9. [0x28] Lock AFI..........................................................................................................98

7.1.10. [0x29] Write DSFI.....................................................................................................99

7.1.11. [0x2A] Lock DSFI................................................................................................... 100

7.1.12. [0x2B] Get System Information...............................................................................101

7.1.13. [0x2C] Get Multiple Block Security Status.............................................................. 105

8. [0xB3] Host commands for EPC Transponders 107

8.1. ISO18000-3M3 Commands [0xB3]................................................................................ 108

8.1.1. [0xB3] [0x18] Kill......................................................................................................108

8.1.2. [0xB3] [0x22] Lock ...................................................................................................110

8.2. [0xBF] ISO15693 Transparent Command.................................................................... 112

Supported ISO15693 Host commands 115

8.3. Supported ISO15693 Host commands for ISO15693 Transponders......................... 115

8.3.1. Fujitsu (MB89R116)................................................................................................115

8.3.2. Fujitsu (MB89R118)................................................................................................115

8.3.3. Fujitsu (MB89R118)................................................................................................117

8.3.4. Fujitsu (MB89R119)................................................................................................118

8.3.5. Infineon (ISO address mode) 0xE0......................................................................... 119

8.3.6. Infineon (My-d Light)...............................................................................................120

8.3.7. NXP (I-Code SLI)..................................................................................................... 121

8.3.8. NXP (I-Code SLI-S).................................................................................................. 122

8.3.9. NXP (I-Code SLI-L)..................................................................................................123

8.3.10. NXP (I-Code SLIX)................................................................................................ 124

8.3.11. NXP (I-Code SLIX-S) ............................................................................................ 125

Identification

Manual

ID ISC.MR102

FEIG ELECTRONIC GmbH

Page 7 of 153

H01113-4e-ID-B.docx

8.3.12. NXP (I-Code SLIX-L).............................................................................................126

8.3.13. NXP (I-Code SLIX2).............................................................................................. 127

8.3.14. NXP ICode ILT-M (ISO18000-3M3) ......................................................................128

8.3.15. STMicroelectronics (LRI64).................................................................................. 129

8.3.16. STMicroelectronics (LRI2k / LRIS2k)....................................................................130

8.3.17. STMicroelectronics (M24LR64-R) ........................................................................ 131

8.3.18. STMicroelectronics (ST25DVxxK-IE/JF)............................................................... 132

8.3.19. Texas Instruments (Tag-it HFI Pro / Standard)..................................................... 134

8.3.20. Texas Instruments (Tag-it HFI Plus)..................................................................... 136

9. Protocols for Notification Mode 138

9.1. The Notification Mode Procedure................................................................................. 138

9.1.1. DATA Structure in Notification Mode........................................................................139

9.2. [0x31] Read Data Buffer Info......................................................................................... 139

9.3. [0x32] Clear Data Buffer................................................................................................ 140

9.4. [0x33] Initialize Buffer.................................................................................................... 140

ANNEX 141

ANNEX A: Codes of Transponder Types............................................................................ 141

ANNEX B: Codes of Identifier Data Types (IDDT) .............................................................. 141

ANNEX C: Time Behavior of the Asynchronous Interface................................................. 141

ANNEX D: Time Behavior of ISO15693 Host Commands .................................................. 142

Time Behavior for [0x01] Inventory and ISO15693 Transponders......................................142

ANNEX E: Index of Status Bytes........................................................................................ 144

ANNEX F: Transponder Error Codes .................................................................................. 147

ANNEX G: Codes of Reader Types ..................................................................................... 148

ANNEX H: Examples for Read Data ................................................................................... 149

ISO15693 Host Command (DB-Size of the Transponder = 4 bytes)................................... 149

ISO15693 Host Command (DB-Size of the Transponder = 8 bytes)................................... 149

ANNEX I: Labeling of configuration parameter.................................................................. 150

Identification

Manual

ID ISC.MR102

FEIG ELECTRONIC GmbH

Page 8 of 153

H01113-4e-ID-B.docx

Safety Instructions / Warning - Read before start-up !

The device may only be used for the intended purpose designed by for the manufacturer.

The operation manual should be conveniently kept available at all times for each user.

Unauthorized changes and the use of spare parts and additional devices which have not been

sold or recommended by the manufacturer may cause fire, electric shocks or injuries. Such

unauthorized measures shall exclude any liability by the manufacturer.

The liability-prescriptions of the manufacturer in the issue valid at the time of purchase are valid

for the device. The manufacturer shall not be held legally responsible for inaccuracies, errors,

or omissions in the manual or automatically set parameters for a device or for an incorrect

application of a device.

Repairs may only be executed by the manufacturer.

Installation, operation, and maintenance procedures should only be carried out by qualified

personnel.

Use of the device and its installation must be in accordance with national legal requirements

and local electrical codes .

When working on devices the valid safety regulations must be observed.

Special advice for carriers of cardiac pacemakers:

Although this device doesn't exceed the valid limits for electromagnetic fields you should keep

a minimum distance of 25 cm between the device and your cardiac pacemaker and not stay in

an immediate proximity of the device respective the antenna for some time.

Identification

Manual

ID ISC.MR102

FEIG ELECTRONIC GmbH

Page 9 of 153

H01113-4e-ID-B.docx

Revision History of documentation

Revi-

sion

Date

Page

Description

12.04.11

Initial version

04.06.12

CFG03: Tag detect, blue LED for ID ISC.ANTS370/270-A

14.11.12

several

Support of ISO18000-3m3 implemented

Read Complete Bank added in CFG11

15.04.15

CFG33/34: TCP/IP Hostname implemented

CFG41: Additional parameter for LAN settings

127

NXP SLIX 2 integrated

05.09.17

40; 139

CFG11: Notification Mode with MAC output configurable

16.02.18

Get Reader Info, new Hardware Version

132

ST25 Transponder implemented

06.07.18

CFG1: HID Delay

06.07.18

CFG20: RF-ON Holdtime

06.07.18

Reader Diagnostic Mode 0x01: Temperature

06.07.18

101

Extended Get System Information

06.07.18

105

Extended Get Multiple Block Security Status

Identification

Manual

ID ISC.MR102

FEIG ELECTRONIC GmbH

Page 10 of 153

H01113-4e-ID-B.docx

Abbreviations

ADR

Address

ASK

Amplitude Shift Keying

Config Block

CFG

Configuration Parameter Block

CRC

Cyclic Redundancy Check

data block

DIP

Dual Inline Plastic

FIFO

First in First out

frq

Frequency

FSK

Frequency Shift Keying

Hour

Hertz

Identification

Input

LEN

Length

LOC

Location

LSB

Least Significant Byte

min

Minutes

Milliseconds

MSB

Most Significant Byte

Number

OUT

Output

R/W

Read / Write Access

Read

REL

Relay

Radio Frequency

RSSI

Received Signal Strength Indicator

RTC

Real Time Clock

TAB

Table

Transponder

Timeslot

UID

Unique Identifier (read only Serial Number)

Write Only Access

Write

Otros manuales para ID ISC.MR102

Otros manuales de Sistema RFID de Feig Electronic

Feig Electronic

Feig Electronic ID HyWEAR compact Manual de usuario

Feig Electronic

Feig Electronic OBID classic-pro ID CPR40.30-A Manual de usuario

Feig Electronic

Feig Electronic OBID i-scan ID ISC.MRU200i Manual de usuario

Feig Electronic

Feig Electronic ID ISC.LRU3500 Manual de usuario

Feig Electronic

Feig Electronic OBID i-scan ID ISC.ANT.UMUX Manual de uso y cuidado

Feig Electronic

Feig Electronic ID ISC.LRMU2000 Manual de usuario

Feig Electronic

Feig Electronic ID RED.M50-E Manual de usuario

Feig Electronic

Feig Electronic ID ISC.LRU3500 Manual de usuario

Feig Electronic

Feig Electronic OBID i-scan ID ISC.MR101-USB Manual de usuario

Feig Electronic

Feig Electronic ID ISC.MRMU102-A Manual de usuario

Feig Electronic

Feig Electronic OBID i-scan ID ISC.LRM2500-A Manual de usuario

Feig Electronic

Feig Electronic ID CPR40.30-U Manual de usuario

Feig Electronic

Feig Electronic OBID classic-pro ID CPR.M04.P/AB-U2 Manual de usuario

Feig Electronic

Feig Electronic OBID classic-pro ID CPR.04.P/AB-USB Manual de usuario

Feig Electronic

Feig Electronic OBID classic-pro ID CPR.03.20-CD Manual de usuario

Feig Electronic

Feig Electronic ID CPR50.10-E Manual de usuario

Feig Electronic

Feig Electronic ID ISC.ANT.U500/270 Manual de usuario

Feig Electronic

Feig Electronic OBID i-scan HF ID ISC.ANT1300/680-GPC Manual de usuario

Feig Electronic

Feig Electronic ID ISC.PRH101-A Manual de usuario

Feig Electronic

Feig Electronic OBID classic-pro ID CPR.02.10-AD Manual de usuario

Feig Electronic

Feig Electronic ID LR5400 Manual de usuario

Feig Electronic

Feig Electronic OBID i-scan Instrucciones de instalación y funcionamiento

Feig Electronic

Feig Electronic OBID i-scan ID ISC.MR101-USB Manual de usuario

Feig Electronic

Feig Electronic OBID i-scan RFID-Tunnel Instrucciones de instalación y funcionamiento

Manuales populares de Sistema RFID de otras marcas

Chainway

Chainway R1 Manual de usuario

IFM

IFM DTC600 Manual de usuario

Elatec

Elatec TWN4 MULTITECH NANO LEGIC 63 M Manual de usuario

RHOMBUS

RHOMBUS DR20 Manual de usuario

Sirit

Sirit IDentity 6204 Manual de usuario

SOREX

SOREX FLEX Manual de usuario

Omron

Omron V780-HMD68-EIP-KR Manual de usuario

IDENTEC SOLUTIONS

IDENTEC SOLUTIONS iPOINT Si Instrucciones de uso

Shuttle

Shuttle BR06 Instrucciones de uso

Digilock

Digilock Curve Keypad Basic Manual de usuario

Atid

Atid AT870 Manual de usuario

Chacon

Chacon 34958 Manual de usuario

Paxton

Paxton PROXIMITY architectural reader Manual de usuario

CipherLab

CipherLab 1800 series Manual de usuario

Brady

Brady FR22 Manual de usuario

Kronotech

Kronotech BLUEBOX GEN2 M30 UHF Manual de usuario

Unitech

Unitech RH767 Manual de usuario

Honeywell

Honeywell 026366.00 Manual de usuario