Feig Electronic OBID i-scan ID ISC.MR101-USB Manual de usuario

INSTALLATION

final

public (B)

2007-09-25

M50805-4e-ID-B.doc

OBI

i-scan

ID ISC.MR101-USB

ID ISC.PR101-USB

OBIDi-scan® Installation ID ISC.MR101-USB / ID ISC.PR101-USB

FEIG ELECTRONIC GmbH Page 2 of 20 M50805-4e-ID-B.doc

Note

FEIG ELECTRONIC GmbH

Lange Strasse 4

D-35781 Weilburg-Waldhausen

Tel.: +49 6471 3109-0

http://www.feig.de

With the edition of this document, all previous editions become void. Indications made in this manual may be

changed without previous notice.

Copying of this document, and giving it to others and the use or communication of the contents thereof are

forbidden without express authority. Offenders are liable to the payment of damages. All rights are reserved

in the event of the grant of a patent or the registration of a utility model or design.

Composition of the information in this document has been done to the best of our knowledge. FEIG

ELECTRONIC GmbH does not guarantee the correctness and completeness of the details given in this

manual and may not be held liable for damages ensuing from incorrect or incomplete information. Since,

despite all our efforts, errors may not be completely avoided, we are always grateful for your useful tips.

The instructions given in this manual are based on advantageous boundary conditions. FEIG ELECTRONIC

GmbH does not give any guarantee promise for perfect function in cross environments.

FEIG ELECTRONIC GmbH assumes no responsibility for the use of any information contained in this

document and makes no representation that they free of patent infringement. FEIG ELECTRONIC GmbH

does not convey any license under its patent rights nor the rights of others.

OBID®and OBID i-scan®are registered trademarks of FEIG ELECTRONIC GmbH.

OBIDi-scan® Installation ID ISC.MR101-USB / ID ISC.PR101-USB

FEIG ELECTRONIC GmbH Page 3 of 20 M50805-4e-ID-B.doc

Contents

1. Safety Instructions / Warning - Read before start-up ! 5

2. Performance Features of the readers 6

2.1. Performance features .........................................................................................................6

2.2. Available Reader-Types......................................................................................................6

3. Assembly and Wiring 7

3.1. Dimensions..........................................................................................................................7

3.2. Connector sockets..............................................................................................................8

3.3. USB-Interface connection X3.............................................................................................8

3.4. Power supply (only ID ISC.MR101)....................................................................................9

3.5. Antenna terminal X4 (only ID ISC.MR101).......................................................................10

3.6. Starting...............................................................................................................................11

3.6.1. ID ISC.MR101..............................................................................................................11

3.6.2. ID ISC.PR101..............................................................................................................11

4. Control and display elements 12

4.1. LED.....................................................................................................................................12

5. Technical Data 13

6. Approvals 15

6.1. Europe (CE)........................................................................................................................15

6.2. Canada (IC) ........................................................................................................................16

6.3. USA.....................................................................................................................................17

6.3.1. FCC .............................................................................................................................17

6.3.2. UL................................................................................................................................17

7. Appendix 18

OBIDi-scan® Installation ID ISC.MR101-USB / ID ISC.PR101-USB

FEIG ELECTRONIC GmbH Page 4 of 20 M50805-4e-ID-B.doc

7.1. Accessories.......................................................................................................................18

7.1.1. Wall mounting kit ID ISC.MS.MR/PR-A.......................................................................19

7.1.2. Antennas......................................................................................................................20

OBIDi-scan® Installation ID ISC.MR101-USB / ID ISC.PR101-USB

FEIG ELECTRONIC GmbH Page 5 of 20 M50805-4e-ID-B.doc

1. Safety Instructions / Warning - Read before start-up !

•The device may only be used for the intended purpose designed by for the manufacturer.

•The operation manual should be conveniently kept available at all times for each user.

•Unauthorized changes and the use of spare parts and additional devices which have not been

sold or recommended by the manufacturer may cause fire, electric shocks or injuries. Such

unauthorized measures shall exclude any liability by the manufacturer.

•The liability-prescriptions of the manufacturer in the issue valid at the time of purchase are valid

for the device. The manufacturer shall not be held legally responsible for inaccuracies, errors,

or omissions in the manual or automatically set parameters for a device or for an incorrect

application of a device.

•Repairs may only be executed by the manufacturer.

•Installation, operation, and maintenance procedures should only be carried out by qualified

personnel.

•Use of the device and its installation must be in accordance with national legal requirements

and local electrical codes .

•When working on devices the valid safety regulations must be observed.

•Special advice for carriers of cardiac pacemakers:

Although this device doesn't exceed the valid limits for electromagnetic fields you should keep

a minimum distance of 25 cm between the device and your cardiac pacemaker and not stay in

an immediate proximity of the device respective the antenna for some time.

OBIDi-scan® Installation ID ISC.MR101-USB / ID ISC.PR101-USB

FEIG ELECTRONIC GmbH Page 6 of 20 M50805-4e-ID-B.doc

2. Performance Features of the readers

2.1. Performance features

The Reader is designed for reading passive data carriers, so-called „Smart Labels“ at an operating

frequency of 13.56 MHz.

The reader ID ISC.MR101 is suitable for all applications in which moderate reading distances are

required. Also required is an external antenna connected to the Reader.

The ID ISC.PR101 is suitable for all applications which don’t require wide reader ranges. The

reader contains of an internal antenna, so that is no external antenna necessary.

An anti-collision function enables simultaneous reading of up to 30 transponders per second.

The Reader electronics is contained in a plastic housing having an IP30 enclosure rating.

Both readers comes with an USB-Interface.

The reader ID ISC.PR101-USB will be powered via the USB-Interface. An additional power supply

is not necessary.

2.2. Available Reader-Types

Reader-Types Description

ID ISC.MR101-A asynchronous RS232 interface and external antenna

ID ISC.MR101-A-M asynchronous RS232 interface and external antenna - Module

ID ISC.MR101-USB USB-Interface and external antenna

ID ISC.PR101-A asynchronous RS232 interface and internal antenna

ID ISC.PR101-A-M asynchronous RS232 interface and internal antenna - Module

ID ISC.PR101-USB USB-Interface and internal antenna

Table 1: Reader-Types

OBIDi-scan® Installation ID ISC.MR101-USB / ID ISC.PR101-USB

FEIG ELECTRONIC GmbH Page 7 of 20 M50805-4e-ID-B.doc

3. Assembly and Wiring

The Reader is designed for an office environment. It can be wall-mounted, in this case the wall-

mount kit should be ordered separately.

(see Appendix: 7.1. Accessories and 7.1.1. Wall mounting kit ID ISC.MS.MR/PR-A

Notes:

•The distance between two readers of the same type should not fall below 4m.

•Before any installation the intended position of the reader should be tested for it´s suit-

ability.

•Only ID ISC.PR101:

The reader must not be installed directly upon conductive materials as e.g. metal sur-

faces, metal grids (reinforcements) or metallized surfaces, as these surfaces reduce the

detection range of the reader. The distance between the reader and such surfaces

should be min. 10 cm.

3.1. Dimensions

RFID by FEIG ELECTRONIC

145 27

Fig. 1: Enclosure (all dimensions in mm)

OBIDi-scan® Installation ID ISC.MR101-USB / ID ISC.PR101-USB

FEIG ELECTRONIC GmbH Page 8 of 20 M50805-4e-ID-B.doc

3.2. Connector sockets

X3 - USB

X1 - VCC

12 - 24 VDC X4 - Antenna

(50 Ω)

LED

Fig. 2: Connection sockets

3.3. USB-Interface connection X3

There is a USB-socket on board for the connection of the USB-Interface. The pinout is standard-

ized. The datarate is reduced to 12 Mbit (USB full speed). A standard USB-cable can be used.

A 2.5m USB-cable is available for the reader.. (see 7.1. Accessories).

Feig Article No. Part No.

1686.000.00 ID CAB.USB-A

Table 2: USB-cable 2,5m

Note:

The length of the USB-cable can be a max. of 3 meter. It isn’t allowed to use longer cables!

The reader ID ISC.PR101-USB does not need an external power supply. The power supply takes

place via the USB-Interface (Bus-powered). The USB-Interface must support a current of about

500mA (High Powered Interface).

OBIDi-scan® Installation ID ISC.MR101-USB / ID ISC.PR101-USB

FEIG ELECTRONIC GmbH Page 9 of 20 M50805-4e-ID-B.doc

3.4. Power supply (only ID ISC.MR101)

Connect the 12-24 V DC/ supply voltage to socket X1 on the circuit board.

Terminal Name Description

X1 / inside Vcc Vcc – supply voltage (+)

X1 / outside GND Ground – supply voltage (-)

Table 3: Connecting the supply voltage

GND

(outside)

Vcc

(inside)

Fig. 3: DC/ socket X1 configuration.

Note:

Reversing the polarity of the supply voltage may destroy the device.

Power supply recommendations :

To take full advantage of the Reader module performance, you must use a sufficiently regulated

and low-noise power supply. When using a switching power supply, be sure that its internal

switching frequency is less than 300 kHz. (see: 7.1. Accessories).

Feig Article No Part No. Description.

1688.000.00 ID NET.12VDC-A Input voltage 230V AC

1688.001.00 ID NET.12VDC-B Input voltage 95 - 265V AC

Table 4: Recommended power supply

Note:

The power supply is supplied with a DC/ plug 2.5mm x 5.5mm. This is compatible with

the readers socket X1.

OBIDi-scan® Installation ID ISC.MR101-USB / ID ISC.PR101-USB

FEIG ELECTRONIC GmbH Page 10 of 20 M50805-4e-ID-B.doc

3.5. Antenna terminal X4 (only ID ISC.MR101)

An SMA socket is provided on the circuit board for connecting the external antenna.

The maximum tightening torque for the SMA socket is 0.45 Nm.

Caution:

Higher tightening torque will damage the connector.

Terminal Description

X4 Connecting the external antenna

(input impedance 50Ω)

Table 5: Connecting the external antenna

Note:

•The input impedance for the antenna must be calibrated to a value of

Ω

(15

Ω

∠

15°).

•If the antenna ID ISC.ANT240340 is used a minimum distance of 20cm to any metal parts

are necessary. Otherwise there is a danger that the reader will be destroyed.

•The optimum operating Q factor of the antenna should be in a range of QB = 10...20. To

determine the operating Q the antenna must be supplied with a 50 Ohm source such as

a network analyzer or frequency generator.

•When connecting an antenna, ensure that it does not exceed the permissible limits pre-

scribed by the national regulations for radio frequency devices.

Otros manuales para OBID i-scan ID ISC.MR101-USB

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Sistema RFID de Feig Electronic

Feig Electronic

Feig Electronic OBID classic-pro ID CPR.M04.P/AB-U2 Manual de usuario

Feig Electronic

Feig Electronic OBID i-scan HF ID ISC.ANT1300/680-GPC Manual de usuario

Feig Electronic

Feig Electronic ID LR5400 Manual de usuario

Feig Electronic

Feig Electronic ID CPR40.30-U Manual de usuario

Feig Electronic

Feig Electronic ID HyWEAR compact Manual de usuario

Feig Electronic

Feig Electronic ID ISC.LRU3500 Manual de usuario

Feig Electronic

Feig Electronic ID ISC.LRU3500 Manual de usuario

Feig Electronic

Feig Electronic OBID ID ISC.ANT40/30 Manual de usuario

Feig Electronic

Feig Electronic ID ISC.MR102 Manual de usuario

Feig Electronic

Feig Electronic ID CPR60 Manual de usuario

Feig Electronic

Feig Electronic ID ISC.ANT1710/690 Crystal Gate Excellence... Manual de usuario

Feig Electronic

Feig Electronic OBID classic-pro ID CPR.04.P/AB-USB Manual de usuario

Feig Electronic

Feig Electronic OBID i-scan ID ISC.ANT.MUX Manual de usuario

Feig Electronic

Feig Electronic OBID classic-pro ID CPR.02.10-AD Manual de usuario

Feig Electronic

Feig Electronic ID ISC.ANT.U500/270 Manual de usuario

Feig Electronic

Feig Electronic OBID i-scan UHF ID ISC.MRU102-PoE-LED Manual de usuario

Feig Electronic

Feig Electronic OBID classic-pro ID CPR40.30-A Manual de usuario

Feig Electronic

Feig Electronic ID ISC.ANT.U500/270-DM Manual de usuario

Feig Electronic

Feig Electronic ID LRU500i-BD Series Manual de usuario

Feig Electronic

Feig Electronic OBID i-scan RFID-Tunnel Instrucciones de instalación y funcionamiento

Feig Electronic

Feig Electronic ID ISC.PRH101-A Manual de usuario

Feig Electronic

Feig Electronic OBID classic-pro ID CPR.03.20-CD Manual de usuario

Feig Electronic

Feig Electronic OBID i-scan ID ISC.MR101-USB Manual de usuario

Feig Electronic

Feig Electronic OBID ID RW40.30-USB Manual de usuario

Manuales populares de Sistema RFID de otras marcas

Chainway

Chainway R1 Manual de usuario

IFM

IFM DTC600 Manual de usuario

Elatec

Elatec TWN4 MULTITECH NANO LEGIC 63 M Manual de usuario

RHOMBUS

RHOMBUS DR20 Manual de usuario

Sirit

Sirit IDentity 6204 Manual de usuario

SOREX

SOREX FLEX Manual de usuario

Omron

Omron V780-HMD68-EIP-KR Manual de usuario

IDENTEC SOLUTIONS

IDENTEC SOLUTIONS iPOINT Si Instrucciones de uso

Shuttle

Shuttle BR06 Instrucciones de uso

Digilock

Digilock Curve Keypad Basic Manual de usuario

Atid

Atid AT870 Manual de usuario

Chacon

Chacon 34958 Manual de usuario

Paxton

Paxton PROXIMITY architectural reader Manual de usuario

CipherLab

CipherLab 1800 series Manual de usuario

Brady

Brady FR22 Manual de usuario

Kronotech

Kronotech BLUEBOX GEN2 M30 UHF Manual de usuario

Unitech

Unitech RH767 Manual de usuario

Honeywell

Honeywell 026366.00 Manual de usuario