F&F BIS-411B Manual de usuario

Tabla de contenidos

Manuales populares de Relé de otras marcas

Shelly

Shelly Pro Series Manual de usuario

GE

GE MVAX 11 Manual de usuario

ABB

ABB RELION REF615R Manual de usuario

Pilz

Pilz PNOZ X10 Manual del propietario

ABB

ABB SPAJ 142 C Manual de lista de piezas

Kemo Electronic

Kemo Electronic B197 Manual de usuario

Seg

Seg MRM3 Manual de usuario

Basler

Basler BE1-700C Manual de usuario

CD Automation

CD Automation REVEX 2PH 280A Manual de usuario

Ruelco

Ruelco 1S04 Manual de usuario

Basler

Basler V3E Z1P B2C1F Manual de usuario

Doepke

Doepke Dupline DSM 2 Manual de usuario

Siemens

Siemens SIRIUS 3RT1966-4D Manual de usuario

GE

GE DGP Manual de usuario

Kyongbo Electronics

Kyongbo Electronics GDR-D01 Manual de usuario

Siemens

Siemens SIPROTEC 4 Manual de usuario

Siemens

Siemens BD2-AK03X/FS Series Manual de usuario

Leuze

Leuze MSI-SR5B Manual de usuario

- 1 -

BIS-411B

Bistable relay

Electronic bistable pulse relay BIS-411B allows switching on or off

the lighting or other device from several different points by paral-

lel connected, momentary (bell) control switches.

A push button on the housing enables direct control of the cir-

cuit without the need to trigger external buttons.

The receiver is switched on after a current pulse caused by pres-

sing any momentary (bell) button connected to the relay. After

the next pulse, the receiver will be switched off. The relay does

not have a "memory" of the contact position, which means in

the event of a power failure and its subsequent return, the relay

contact will be set to "off". This prevents the controlled receivers

from being switched on automatically without supervision after

a prolonged power failure. The button on the housing performs

exactly the same function as the external button connected to

the terminals of the device.

Purpose

Functioning

F&F Filipowski sp. j.

Konstantynowska 79/81, 95-200 Pabianice, POLAND

phone/fax (+48 42) 215 23 83 / (+48 42) 227 09 71

www.fif.com.pl; e-mail: biuro@fif.com.pl

Do not dispose of this device in the trash along with other waste! According to the Law on

Waste, electro coming from households free of charge and can give any amount to up to

that end point of collec� on, as well as to store the occasion of the purchase of new equip-

ment (in accordance with the principle of old-for-new, regardless of brand). Electro thrown

in the trash or abandoned in nature, pose a threat to the environment and human health.

- 2 -

1.Disconnect the power supply.

2.Fix the relay on a rail in the control box.

3.Connect the power wires to terminals 1-3 according to the se-

lected relay control option (control pulse L or N).

4.Momentary switches connected in parallel, connect to termi-

nal 6 and to the wire to which terminal 3 is connected.

5.Connect the powered receiver in series to terminals 11-12.

The maximum total backlight current of all connected

buttons must not exceed 5 mA.

BIS-411B can work with backlit buttons.

Mounting

- 3 -

Wiring diagram

- 4 -

1-3 power supply of the relay 165÷265 V AC

6 control input

10 NC contact (passive)

11 relay common contact (COM)

12 NO contact (active)

- 5 -

power supply 165÷265 V AC

contact separated 1×NO/NC

maximum load current (AC-1) 16 A

control pulse current 5 mA

activation delay 0.1÷0.2 s

power supply indication green LED

activation indication red LED

mechanical life of the button 10⁶ cycles

power consumption

stand-by 0.15 W

on 0.6 W

terminal 2.5 mm² screw terminals

tightening torque 0.4 Nm

working temperature -25÷50°C

dimensions 1 module (18 mm)

mounting on TH-35 rail

ingress protection IP20

Technical data

- 6 -

tungsten halogen fluorescent energy-saving LED

2000 W 1250 W 1000 W 500 W 250 W

The above data are indicative and will heavily depend on the

design of a specific receiver (that is especially important for

LED bulbs, energy-saving lamps, electronic transformers and

pulse power supply units), switching frequency and operating

conditions.

For more information visit: www.fif.com.pl.

The F&F products are covered by a warranty of the 24 months

from the date of purchase. Effective only with proof of purchase.

Contact your dealer or directly with us.

F&F Filipowski sp. j. declares that the device is in conformity

with the essential requirements of The Low Voltage Directive

(LVD) 2014/35/EU and the Electromagnetic Compatibility (EMC)

Directive 2014/30/UE. The CE Declaration of Conformity, along

with the references to the standards in relation to which confor-

mity is declared, can be found at www.fif.com.pl on the product

page.

Power table

Warranty

CE declaration

E210119