F&F BIS-412M 24V Manual de usuario
- 1 -
Electronic bistable pulse relay BIS-412M is designed to work in
a group system. The single relay allows you to control the re-
ceiver using momentary (bell) buttons, connected to local con-
trol inputs. Additionally, thanks to the central control inputs, it
is possible to group control of many receivers simultaneously.
The lighting of the green LED marked with the U symbol means
that the device is properly powered. The device can be control-
led from the level of local and central inputs.
Local control
The receiver is turned on (the relay contact is switched to po-
sition 7-10) after pressing any momentary button from the local
control group. The activation of the receiver is signaled by the
lighting of the red LED diode. Another pressing of the button
from the local control group will turn off the receiver (the con-
tact returns to position 7-12).
Purpose
Functioning
F&F Filipowski sp. j.
Konstantynowska 79/81, 95-200 Pabianice, POLAND
phone/fax (+48 42) 215 23 83 / (+48 42) 227 09 71
www.fif.com.pl; e-mail: biuro@fif.com.pl
Do not dispose of this device in the trash along with other waste! According to the Law on
Waste, electro coming from households free of charge and can give any amount to up to
ment (in accordance with the principle of old-for-new, regardless of brand). Electro thrown
in the trash or abandoned in nature, pose a threat to the environment and human health.
BIS-412M 24V
Bistable relay (group) with
„memory” contact position
- 2 -
Central control
(input no. 9) – pressing the momentary
button connected to this input will always turn off the receiver
(regardless of its previous state). The relay contacts will be swit-
ched to position 7-12. This input allows you to centrally control a
group of devices with a single button.
(input no. 4) – pressing the momentary
button connected to this input will always turn on the receiver
(regardless of its previous state). The relay contacts will be swit-
ched to position 7-10. This input allows you to centrally control a
group of devices with a single button.
The relay has the feature of the so-called "memory" of the con-
tact position, which means when the power supply is switched
back on, the relay will be restored to the state it was in when the
power supply was switched off.
1.Disconnect the power supply.
2.Fix the relay on a rail in the control box.
Do not install a device that is damaged or incomplete.
3.Connect the power wires to terminals 1-3 according to the
diagram.
A group of relays working with common central control
must be powered from the same line (~) for AC or only
from (+) for DC.
Mounting
- 3 -
Be especially careful when installing the controller.
Incorrect connection may result in electric shock and/or
damage to the controller and the powered device.
4.Connect the local control and central control switches to the
relay terminals according to the function and to the common
wire (~) or (+).
Connecting to the control inputs of relays of different
lines (~) or (+) may cause incorrect operation of the sys-
tem and lead to an electric short circuit in the installa-
tion and destruction of the controllers.
5.Connect the relay contact in series into the power supply cir-
cuit of the controlled receiver (lighting) (connect the power
to terminal 7; supply the controlled receiver from the contact
10).
6.Connect the power supply.
BIS-412M 24V is not compatible with backlit buttons.
Contact configuration
- 4 -
1-3 relay power supply 9÷30 V AC/DC
4 central control:
6 local control:
9 central control:
7-10-12 1×NO/NC separated changeover contact
With the DC supply voltage, the control inputs can be
powered only from the "plus" wire (+).
Wiring diagram
- 5 -
Group system diagram
- 6 -
power supply 9÷30 V AC/DC
contact separated 1×NO/NC
maximum load current (AC-1) 16 A
activation delay 0.1÷0.2 s
power indication green LED
signalling indication red LED
power consumption
standby 0.15 W
on 0.6 W
working temperature -25÷50°C
dimensions 1 module (18 mm)
mounting on TH-35 rail
ingress protection IP20
Table for loads supplied with 230 V AC:
tungsten halogen fluorescent energy-saving LED
The above data are indicative and will heavily depend on the
design of a specific receiver (that is especially important for
LED bulbs, energy-saving lamps, electronic transformers and
conditions.
For more information visit: www.fif.com.pl.
Technical data
Power table
- 7 -
The F&F products are covered by a warranty of the 24 months
ffrom the date of purchase. Effective only with proof of purcha-
se. Contact your dealer or directly with us.
F&F Filipowski sp. j. declares that the device is in conformity
(LVD) 2014/35/EU and the Electromagnetic Compatibility (EMC)
Directive 2014/30/UE.
The CE Declaration of Conformity, along with the references to
the standards in relation to which conformity is declared, can be
found at www.fif.com.pl on the product page.
Warranty
CE declaration
E220126
Tabla de contenidos
Otros manuales de Relé de F&F
F&F
F&F PCS-516 DUO Manual de usuario
F&F
F&F 5908312595649 Manual de usuario
F&F
F&F PP-1P Manual de usuario
F&F
F&F MST-03 Manual de usuario
F&F
F&F PCS-517.2 Manual de usuario
F&F
F&F BIS-404 Manual de usuario
F&F
F&F BIS-409 Manual de usuario
F&F
F&F PK-2P Manual de usuario
F&F
F&F BIS-408 Manual de usuario
F&F
F&F 5908312592389 Manual de usuario
F&F
F&F FW-R2D Manual de usuario
F&F
F&F FOX HERMETIC BOX Manual de usuario
F&F
F&F PP-1Z-LED Pico Manual de usuario
F&F
F&F PCS-516UNI Manual de usuario
F&F
F&F FW-R2P Manual de usuario
F&F
F&F BIS-408i Manual de usuario
F&F
F&F CP-721-FPV Manual de usuario
F&F
F&F PZ-829 RC Manual de usuario
F&F
F&F BIS-410i Manual de usuario
F&F
F&F BIS-411BM-LED Manual de usuario
