Extron electronics PVT RGB D Plus Manual de usuario

Installation

1. Using the mud ring or a junction box as a guide, mark the edges and cut out

the material within the marked area.

NOTE: If installing a junction box, allow enough depth for the wallplate and

cables. The box should be at least 2.0 inches (5.1 cm) deep for the

connectors and cables.

2. Either:

Insert the mud ring into the opening, rotate the locking arms, and secure

with the supplied screws,

Or, Insert the wall box and secure with nails or screws.

3. Run the CAT 5 cables from the PoleVault switcher location, going behind the

wall and to the PVT location, then thread the cables through the mud ring or

wall box.

NOTE: Two cables (A and B) are needed for RGB signals.

NOTE: The CAT 5 cables supplied are terminated to the TIA 568A standard.

Other CAT 5 cables can be used if they are TIA 568A or TIA 568B

standards and terminated to the same standard at both ends.

4. Connect the cables to connectors on the rear of the wallplate (cable labeled

A to port A, cable B to port B).

5. If available, connect the switcher line out port to the rear panel 3-pole captive

screw connector, using a line out audio cable: L = left (tip), R = right (ring),

G = ground (sleeve). See inset, step 5.

6. Connect an IR cable from the MediaLink® Controller to the rear panel IR connector

by inserting the signal wire into the hole marked “S” and the ground wire into

the hole marked “G” (see inset, step 6).

7. If the display refresh rate and resolution is known, set the EDID Minder

5-pole DIP switches according to the EDID table (see reverse side for details).

Alternatively, if the EDID Minder is used in the learn mode, set all the DIP switches to off.

8. Mount the device into the mud ring or wall box and attach the supplied Decora faceplate.

9. Connect a source device to “Computer In” and a local display device to “Monitor Out.”

10. Connect the IR emitter to the front panel 2-pole captive screw connector with the signal

wire in the hole marked “S” and the ground wire in the hole marked “G.”

Place the IR emitter near or in front of the IR pickup sensor on the device.

11. To complete system installation refer to the PoleVault System Installation Guide,

available at www.extron.com.

The Extron® PVT RGB D Plus with EDID is a 1-gang A/V wallplate for

PoleVault™ Systems that transmits high-resolution computer video and

audio signals to the PoleVault switcher. This model incorporates

EDID Minder®, which allows the transmitter to communicate the appropriate

EDID information to the source, ensuring correct video output resolution.

See reverse side for EDID Minder operation.

NOTE: The 5-pole EDID Minder settings switch is located on the rear of the wallplate. After

installation, these switch settings are only accessible by removing the device from its installed

location. The factory EDID setting (default) is 1024x768@60 Hz (preset 2).

Continued on side 2.

COMPUTER IN

AUDIO

IN OUT

MONITOR OUT

IR OUT

S G

COMPUTER IN

AUDIO

MONITOR OUT

IR OUT

S G

IN OUT

Decora®

Faceplate

Extron

PVT RGB D Plus (EDID)

Wall

Wall Mounting

Bracket (mud ring)

RGB output cables

Wire Color

White-green

Green

White-orange

White-blue

Orange

White-brown

Brown

568A

Blue

Wire Color

568B

White-green

Green

White-orange

White-blue

Orange

White-brown

Brown

Blue

12345678

RJ-45

Connector

Insert Twisted

Pair Wires

Pins:

IR OUT

S G

Step 5

Step 6

Step 10

PVT RGB D Plus (EDID) • Setup Guide

EDID Minder

The EDID Minder has two modes; a preset mode and a learn mode.

Preset mode allows selection of pre-programed EDID rates, as shown in the table below.

Learn mode enables the displays speciﬁc EDID information to be recorded and emulated

by the input wallplate.

To use the EDID Minder mode in preset or learn Mode, follow the instructions below.

Using Preset mode

1. If already installed, disconnect any sources and displays from the front panel and

remove the wallplate from the wall.

2. On the rear panel, set DIP switch 1 to the 50 or 60 kHz setting as desired.

Set DIP switches 2 to 5 accordingly, to match the desired EDID rate (see table below).

3. Connect the video source to the “Computer In” VGA connector and a local display

device to the “Monitor Out” port.

4. Restart the video source and display devices. Verify the image, making any

changes to the EDID settings as needed.

5. When the image is correct, re-install the wallplate. Re-connect and restart the source and display devices.

Preset

Number

Switch setting Resolution

2345

0 Off Off Off Off Learn mode

1 Off Off Off On 800 x 600

2 Off Off On Off 1024 x 768 (default)

3 Off Off On On 1280 x720

4 Off On Off Off 1280 x 768

5 Off On Off On 1280 x 800

6 Off On On Off 1280 x 1024

7 Off On On On 1360 x 768

8 On Off Off Off 1366 x 768

9 On Off Off On 1400 x 1050

A On Off On Off 1440 x 900

B On Off On On 1600 x 1200

C On On Off Off 1680 x 1050

D On On Off On 1920 x 1080

E On On On Off 1920 x 1200

F On On On On N/A

Using Learn mode

1. Disconnect any sources from the front panel and remove the wallplate from the wall.

2. On the rear panel, set all the DIP switches to off (down).

3. Temporarily connect the main display device (the projector) to the “Monitor Out” port.

4. On the front panel, the learn LED is lit solid green. Press and release the Learn button.

5. The LED ﬂashes red when in learn mode, then returns to solid green when complete.

6. Re-install the wallplate and reconnect the source device.

Connect a local display device to the “Monitor Out” port as needed.

7. Reconnect the projector to the PoleVault switcher. Restart the source and display devices.

Extron USA - West

Headquarters

+800.633.9876

Inside USA / Canada Only

+1.714.491.1500

+1.714.491.1517 FAX

Extron USA - East

+800.633.9876

Inside USA / Canada Only

+1.919.863.1794

+1.919.863.1797 FAX

Extron Europe

+800.3987.6673

Inside Europe Only

+31.33.453.4040

+31.33.453.4050 FAX

Extron Asia

+800.7339.8766

Inside Asia Only

+65.6383.4400

+65.6383.4664 FAX

Extron Japan

+81.3.3511.7655

+81.3.3511.7656 FAX

Extron China

+400.883.1568

Inside China Only

+86.21.3760.1568

+86.21.3760.1566 FAX

Extron Middle East

+971.4.2991800

+971.4.2991880 FAX

68-1823-50

Rev B

10 10

COMPUTER IN

AUDIO

IN OUT

MONITOR OUT

IR OUT

S G

EDID Learn

Status LED

EDID Learn

Button

EDID

Selection

1 2 3 4

NOTE This setting is for 1024x768@60 Hz,

preset 2 (factory default)

PVT RGB D Plus (EDID) • Setup Guide, cont’d

Otros manuales de Transmisor de Extron electronics

Extron electronics

Extron electronics DTP3 T 101 D Manual de usuario

Extron electronics

Extron electronics ExSens Manual de usuario

Extron electronics

Extron electronics DTP T HWP D Series Manual de usuario

Extron electronics

Extron electronics DTP3 T 101 D Manual de usuario

Extron electronics

Extron electronics DTP2 T 203 Manual de usuario

Extron electronics

Extron electronics DTP T UWP 4K 232 D Manual de usuario

Extron electronics

Extron electronics XTP T HDMI Manual de usuario

Extron electronics

Extron electronics XTP T FB 202 4K Manual de usuario

Extron electronics

Extron electronics UCS FT 901 Manual de usuario

Extron electronics

Extron electronics DTP2 T 203 Manual de usuario

Extron electronics

Extron electronics USB Extender Plus Series Manual de usuario

Extron electronics

Extron electronics MTP T 15HD A Manual de usuario

Extron electronics

Extron electronics XTP T VGA Manual de usuario

Extron electronics

Extron electronics DTP DVI 230 Manual de usuario

Extron electronics

Extron electronics PVT CV Manual de usuario

Extron electronics

Extron electronics DTP2 T 201 D Manual de usuario

Extron electronics

Extron electronics XTP T HWP 101 4K Manual de usuario

Extron electronics

Extron electronics XTP T HWP 101 Manual de usuario

Extron electronics

Extron electronics DTP T FB 332 Manual de usuario

Extron electronics

Extron electronics XTP T UWP 202 4K Manual de usuario

Extron electronics

Extron electronics DVI 201 Tx/Rx Manual de usuario

Extron electronics

Extron electronics DTP2 T 201 D Series Manual de usuario

Extron electronics

Extron electronics FOX3 T 201 Manual de usuario

Extron electronics

Extron electronics PVT CV D Manual de usuario

Manuales populares de Transmisor de otras marcas

NIVELCO

NIVELCO EasyTREK SCA-300 Series Manual del propietario

Honeywell

Honeywell 5816WMBR Manual de usuario

Kamstrup

Kamstrup READy MTU Instrucciones de funcionamiento

Omega

Omega ZW Series Manual de usuario

ABB

ABB Field 264H Guía

Alinco

Alinco DJ-V17T Manual de usuario

Dejero

Dejero EnGo 3x Manual de usuario

Rosemount

Rosemount 4600 Manual de usuario

Speaka Professional

Speaka Professional 2342740 Manual de usuario

trubomat

trubomat GAB 1000 Manual de usuario

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Manual de usuario

Rondish

Rondish UT-11 Manual de usuario

MG 10JRE Manual de usuario

Burkert

Burkert 8177 Manual de usuario

Firetide

Firetide HotPort 3203 Manual

Tele Radio

Tele Radio T9-02 Manual de usuario

Rotronic

Rotronic HygroFlex HF3 Series Manual de usuario

Jamara

Jamara FCX6 Pro Tel Manual de usuario