Extron electronics DTP DVI 330 Manual de usuario

IMPORTANT:

Go to www.extron.com for the complete

user guide, installation instructions, and

specifications before connecting the

product to the power source.

DTP DVI 330 • Setup Guide

This guide provides quick start instructions for an experienced installer to set up and operate the Extron DTP DVI 330 digital video

extender. The DTP DVI 330 transmitter and receiver pair can extend an HDCP-compliant DVI signal up to 330 feet (100 m).

Installation

Step 1 — Mounting

Turn off or disconnect all equipment power sources and mount the Tx and Rx units as required.

Step 2 — Connections

aDVI Input connector (Tx) — Connect an DVI cable between this port and the DVI output port of the digital video source.

bLocal Output connector (Tx) — If desired, connect a DVI monitor for local monitoring of the input digital image.

cAudio input (Tx) — Connect an unbalanced stereo audio source to this 3.5 mm mini stereo jack for an analog audio input.

dRS-232 and IR connectors (both units) — To pass serial or infrared data or control signals,

such as serial control of a projector, connect the primary device to the transmitter and the

secondary device to the receiver via the RS-232 and IR captive screw connectors on both

units.

eDTP RJ-45 connectors (both units) — Connect transmitter DTP Out to receiver DTP In.

Extron recommends that you terminate both cable ends in accordance with the following

specifications, at a minimum:

• TIA/EIA T 568 B •CAT 6A, shielded •24 AWG, solid conductor

ATTENTION:

• Do not connect these devices to a computer data or telecommunications network.

• Ne connectez pas ces appareils à un réseau de télécommunications ou de données

informatiques..

Sig(nal) LED (both units) — Lights when the unit is receiving a TMDS clock signal on the DVI input

(transmitter) or any valid signal on the DTP In connector (receiver).

Link LED (both units) — Lights when a valid link is established between the units on the DTP cable.

fDVI Output connector (Rx) — Connect a display with an DVI input for display of the transmitted direct digital image.

gAudio Output connector (Rx) — Connect a balanced or unbalanced stereo or mono audio device to the receiver via the Audio

captive screw connector. See the drawing on page 2.

DTP DVI 330 Tx

DTP DVI 330 Rx

L R

OUTPUTS

DVI-D

AUDIO

DTP DVI 330 Rx

INPUTSLOCAL OUTPUT

AUDIODVI-D

DTP DVI 330 Tx Rx GTx

RS-232 IR

RxTx

POWER

12V

0.8 A MAX

SIG LINK

DTP OUT

OVER DTP

Rx GTx

RS-232 IR

RxTx

POWER

12V

0.8 A MAX

SIG LINK

DTP IN

OVER DTP

LOCAL

REMOTE

1 2

DDC ROUTE

Front Rear 4

1 523

Front Rear 47

6 5

Wire color

White-green

Green

White-orange

White-blue

Orange

White-brown

Brown

Blue

TIA/EIA T

568 B

TP Wires

12345678

Pins:

Ground

Receiv

e pin on connected unit

ansmit pin on connected unit

Connected RS-232

and IR Device Pins

Tx/Rx

Pins

Receiv

e pin on connected unit

ansmit pin on connected unit

Rx GTx

RS-232 IR

RxTx

68-2342-50 Rev. B

1120

For information on safety guidelines, regulatory compliances, EMI/EMF compatibility, accessibility, and related topics, see the

Extron Safety and Regulatory Compliance Guide on the Extron website.

All trademarks mentioned are the property of their respective owners.

Worldwide Headquarters: Extron USA West, 1025 E. Ball Road, Anaheim, CA 92805, 800.633.9876

Unbalanced Stereo Output Balanced Stereo Output

Do not tin the wires!

Tip

Ring

Tip

Ring

Sleeves

Tip

No Ground Here

Tip

Sleeves

ATTENTION:

•Connect the sleeves to the ground contact. DO NOT connect the sleeves to the negative (-) contacts.

•Raccordez les manchons à la masse (GND). Ne PAS connecter les manchons aux contacts négatifs (–).

hPower connector — Connect an IEC power cord between the included 12 VDC

power supply and a 100-240 VAC, 50-60 Hz source. Connect the power supply

to either unit as shown at right. Use the included tie-wrap to strap the cord to the

captive screw connector.

NOTE: Only one power supply is required. A single power supply connected to

either unit in the pair powers both units. A power supply is included with each

transmitter.

Operation

After all devices are powered up, the system is fully operational. See the denitions

Rear

(Tx)

LOCAL

SPARE

REMOTE

DDC ROUTE

POWER

12V

0.8 A MAX

1 2

2 3

of the power indications (shown at right), below:

aPower LED (front panel) —

Amber — The unit is receiving power, either locally or remotely (on the DTP cable).

Green — The unit is powered on and is receiving an active DVI signal, either on the DVI

input if a transmitter, or transmitted on the DTP cable if a receiver.

bPower LED (rear panel) —

Amber — The unit is receiving power remotely (on the DTP cable).

Green — The unit is receiving power locally.

cDDC Route switch — This rear panel switch selects either the remote or local DVI display as the display data channel (DDC)

reference for EDID and HDCP communication.

If any problems are encountered, verify that the cables are routed and connected properly. If your problems persist, call the Extron S3

Sales and Technical Support Hotline that is closest to you, at the number shown below.

LockIt™ Lacing Brackets

1. Use an included LockIt Lacing Bracket to securely fasten an DVI cable to each device as follows.

2. Plug the DVI cable into the panel connection (a).

3. Loosen the DVI connection mounting screw from the panel enough to allow the LockIt lacing

bracket to be placed over it (b). The screw does not have to be removed.

4. Place the LockIt lacing bracket on the screw and against the DVI connector, then tighten the screw

to secure the bracket (c).

ATTENTION: Do not overtighten the DVI connector mounting screw. The shield it fastens

to is very thin and can easily be stripped.

5. Loosely place the included tie wrap around the DVI connector and the LockIt lacing bracket as

shown (d).

6. While holding the connector securely against the lacing bracket, use pliers or similar tools to tighten the tie wrap, then remove any

excess length (e).

Power Supply

Output Cord

Ridges

Smooth

Captive

Screw

Connector

16 (5 mm) Max

SECTION A–A

Otros manuales para DTP DVI 330

Este manual sirve para los siguientes modelos

Otros manuales de Transmisor de Extron electronics

Extron electronics

Extron electronics DTP2 T 201 D Manual de usuario

Extron electronics

Extron electronics DTP T EU 4K 331 Manual de usuario

Extron electronics

Extron electronics DVI 201xi TX Manual de usuario

Extron electronics

Extron electronics XTP T VGA Manual de usuario

Extron electronics

Extron electronics ExSens Manual de usuario

Extron electronics

Extron electronics FOX3 T 201 Manual de usuario

Extron electronics

Extron electronics UCS FT 901 Manual de usuario

Extron electronics

Extron electronics A/V Receiver MTP 4T 15HD RS Manual de usuario

Extron electronics

Extron electronics A/V Receiver MTP 4T 15HD RS Manual de usuario

Extron electronics

Extron electronics TP Series Manual de usuario

Extron electronics

Extron electronics DTP3 T 101 D Manual de usuario

Extron electronics

Extron electronics MTP U T A D Manual de usuario

Extron electronics

Extron electronics MTP 15HD A Series Manual de usuario

Extron electronics

Extron electronics DTP3 T 203 Manual de usuario

Extron electronics

Extron electronics XTP T EU 202 Manual de usuario

Extron electronics

Extron electronics XTP T UWP 202 4K Manual de usuario

Extron electronics

Extron electronics DTP T UWP 4K 232 D Manual de usuario

Extron electronics

Extron electronics DVI 201 A D Tx/Rx Manual de usuario

Extron electronics

Extron electronics FOX3 T 301 Manual de usuario

Extron electronics

Extron electronics XTP FT HD 4K Manual de usuario

Extron electronics

Extron electronics PowerCage MTP AV Series Manual de usuario

Extron electronics

Extron electronics XTP T UWP 202 Manual de usuario

Extron electronics

Extron electronics DVI 201xi TX Manual de usuario

Extron electronics

Extron electronics PowerCage FOX 4G Tx VGA Manual de usuario

Manuales populares de Transmisor de otras marcas

NIVELCO

NIVELCO EasyTREK SCA-300 Series Manual del propietario

Honeywell

Honeywell 5816WMBR Manual de usuario

Kamstrup

Kamstrup READy MTU Instrucciones de funcionamiento

Omega

Omega ZW Series Manual de usuario

ABB

ABB Field 264H Guía

Alinco

Alinco DJ-V17T Manual de usuario

Dejero

Dejero EnGo 3x Manual de usuario

Rosemount

Rosemount 4600 Manual de usuario

Speaka Professional

Speaka Professional 2342740 Manual de usuario

trubomat

trubomat GAB 1000 Manual de usuario

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Manual de usuario

Rondish

Rondish UT-11 Manual de usuario

MG 10JRE Manual de usuario

Burkert

Burkert 8177 Manual de usuario

Firetide

Firetide HotPort 3203 Manual

Tele Radio

Tele Radio T9-02 Manual de usuario

Rotronic

Rotronic HygroFlex HF3 Series Manual de usuario

Jamara

Jamara FCX6 Pro Tel Manual de usuario