Extron electronics DTP2 T 201 D Series Manual de usuario

IMPORTANT:

Go to www.extron.com for the

complete user guide, installation

instructions, and specifications.

DTP2 T 201 D Series • Setup Guide

This setup guide provides instructions for an experienced installer to set up the Extron DTP2 T 201 D Transmitter.

Installation

Step 1 — Disconnect Power

Disconnect all equipment from power sources.

Step 2 — Prepare the Mounting Surface

NOTES:

• Use a wall box with a depth of at least 3.0 inches (7.6

cm). Alternatively, the included mud ring (MR 100) can

be used.

• For more information, see the full product user guide at

www.extron.com. The installation must comply with

the National Electrical Code and all applicable local

codes.

Refer to gure2 for the following steps.

a. Place the wall box against the installation surface and

mark the opening guidelines.

b. Cut out the material from the marked area.

c. Secure the wall box with 10-penny nails or #8 or #10 screws, leaving the front edge flush with the surface.

d. Run all required cables (see steps 4and 5, on the next pages) and secure them with cable clamps.

e. Do not install the transmitter into the wall box until a later step.

TIP: To ensure a proper t the unit in the junction box, do not install boots on TP cables and RJ-45 connectors.

Step 3 — Connect Input to the Transmitter

Connect an HDMI cable between the HDMI input connector and the output of the digital video source (see figure1, A).

HDMI IN

LINK

OUT

DTP2 T 201 D

OFF

SEND

POWER

12V

--A MAX

HDBT

DTP

CONFIG

DTP2 T 201 D

Front Panel

DTP2 T 201 D

Rear Panel

Top View

DTP2 T 201 D

Bottom View

A HDMI input connector

B Send Power mode switch

C Power connector

D DTP OUT connector

E USB Configuration port

F HDBaseT/DTP mode switch

G Grounding Screw

Wall Stud

Screws

or Nails

Signal

Output

Cable

HDMI IN

LINK

Decorator-Style Faceplate

Extron

DTP2 T 201 D

Transmitter

Figure 2. Typical DTP2 T 201 D Wall Installation

2 Figure 1. DTP2 T 201 D Front and Rear Panels

DTP2 T 201 D • Setup Guide (Continued)

Step 4 — Set DTP/HDBT and SEND POWER Switches

Connect an RJ-45 DTP or HDBT receiving device to the output (see ﬁgure1, Don the previous page) for either DTP or HDBT

model.

zFor DTP2 series receivers, set the DTP/HDBT switch (F) to DTP and the SEND POWER switch (B) to the UP (SEND POWER)

position. On the receiver, set the SEND POWER switch to the Down (OFF) position (see figure 3 below).

zFor legacy DTP series, set the DTP/HDBT toggle switch (F) to DTP, and the SEND POWER switch (B) to the Down (OFF)

position (see figure 3 below).

zIf the receiver is HDBaseT enabled, set the DTP/HDBT toggle switch (F) to HDBT,and the SEND POWER switch (B) to the

Down (OFF)position.

ATTENTION:

• Position these toggle switches (see ﬁgure1, Fand B)BEFORE connecting the appropriate device to the TP

connector. Failure to comply can damage the endpoint.

• Positionnez ces sélecteurs (voir ﬁgure1, F et B) AVANT de connecter l’appareil approprié au connecteur TP. Ne

pas respecter cette procédure pourrait endommager le point de connexion.

• The DTP2 T 201 D device is congured to output power to DTP2 models only. If connected to a legacy DTP or

HDBT device, set the SEND POWER toggle switch to the Down position (OFF). Failure to turn the power OFF will

damage the connected DTP device.

• Le DTP2 T 201 D est conguré pour fournir une alimentation aux modèles DTP2 uniquement. S’il est connecté à un

autre appareil, veuillez positionner l’interrupteur à bascule sur « Down » (OFF). Si l’interrupteur n’est pas positionné

sur OFF, vous risquez d’entraîner la défaillance de l’appareil legacy DTP connecté.

SEND

POWER

OFF

SEND

POWER

OFF

SEND

POWER

OFF

SEND

POWER

OFF

SEND

POWER

OFF

OUT

DTP2 T 201 D

OFF

SEND

POWER

12V

--A MAX

OUT

DTP2 T 201 D

OFF

SEND

POWER

12V

--A MAX

OUT

DTP2 T 201 D

OFF

SEND

POWER

12V

--A MAX

DTP HDMI 330 Rx

OVER DTP

RS-232 IR

Tx Rx Tx RxG

DTP2 R 211

CONFIG

INPUT

LINK

OUTPUT

SEND

POWER

OFF

STATUS

DTP2 R 211

CONFIG

INPUT

LINK

OUTPUT

SEND

POWER

OFF

STATUS

Local

Power Supply

CATx Cable

up to 330' (100 m)

Local

Power Supply

No Remote Power

Extron

DTP2 T 201 D

Transmitter

Extron

DTP HDMI 4K 330 Rx

Receiver

DTP2 Endpoint Connected to a DTP Endpoint

CATx Cable

up to 330' (100 m)

Direction of

Remote Power

Local

Power Supply

Extron

DTP2 T 201 D

Transmitter

Extron

DTP2 R 211

Receiver

CATx Cable

up to 330' (100 m)

Direction of

Remote Power

Extron

DTP2 T 201 D

Transmitter

Extron

DTP2 R 211

Receiver

DTP2 Endpoint Connected to a DTP2 Endpoint

Local

Power Supply

Figure 3. Send Power Toggle Switch Conﬁguration

3 NOTE: When the output is configured

for DTP mode, remote power is

available for Extron DTP2 devices

only. When the output is configured

for HDBT mode, remote power is

disabled and both the switcher and

receiver require their own 12VDC

power supply.

Step 5 — Run Cable Between Units

NOTE: The DTP2 T 201 D product can transmit video, control, and audio (if applicable) signals up to 330feet (100 m).

Connect the transmitter output (see ﬁgure1, D) to the receiver input using shielded twisted pair (STP) cable.

For optimal performance, Extron highly recommends the following:

ATTENTION:

• Do not use Extron UTP23SF-4 Enhanced Skew-Free AV UTP cable or STP201 cable.

• N’utilisez pas le câble AV Skew-FreeUTP version améliorée UTP23SF d’Extron ou le câble STP201.

zRJ-45 termination with STP cable must comply with TIA/EIA T 568B wiring standard for all

connections (see image to the right to properly wire the RJ-45 connector).

zUse shielded twisted pair cable, 24 AWG solid conductor or better, with a minimum cable

bandwidth of 400 MHz.

zUse shielded RJ-45 plugs to terminate the cable.

zLimit the use of RJ-45 patches. Overall transmission distance capabilities vary depending on the

number of patches used. If possible, limit the number of patches to only 1 or 2 total.

zIf RJ-45 patches must be used in the system, shielded CAT 6 (or better) patches are recommended.

Step 6 — Connect Outputs from the Receiver

The DTP2 T 201 D transmitter is compatible with DTP 230 and DTP 330 receivers (sold separately). Connect an HDMI cable

between the receiver HDMI output port and the input port of the display device.

Step 7 — Power the Units

When the unit is congured for DTP mode via the HDBT/DTP switch (see ﬁgure1, F), the

unit can be powered either locally, with the included external 12 VDC power supply, or over

the DTP line by a locally powered receiver or switcher.

When congured for HDBaseT mode, remote power capability is disabled, and the unit must

be powered locally.

To power the unit locally in either mode, wire the 2 pole captive screw connector for the

included external 12 VDC power supply as shown at right. Plug the power supply captive

screw connector into C.

Step 8 — Final Installation

a. Make all connections and test the system for satisfactory operation.

b. Run all required cables (see steps 4, 5, and 7) and secure them, as needed, with cable clamps.

c. At the power outlet for the transmitter, if connected, unplug the power supply.

d. Mount the transmitter into the wall box and attach the supplied decorator-style faceplate to the unit (see figure2).

e. At the power outlet, reconnect the power supply.

f. Power up all attached devices, including displays.

Operation

After all devices are powered up, the system is fully operational. See the denitions of the power indications below.

Transmitter Power and Link Indicators

• Power LED — This two-color front panel LED on the DTP2 T 201 D transmitter lights to indicate signal and power status as

follows:

• Amber — The unit is receiving power but no signal is present on the HDMI input.

• Green — The unit is receiving power and a signal is present on the HDMI input.

• Link LED — This green LED lights to indicate when a valid link is established between the units on the DTP cable.

SECTION A–A

Power Supply

Output Cord

Captive Screw

Connector

Ridges

Smooth

3/16"

(5 mm) Max.

Wire color

White-green

Green

White-orange

White-blue

Orange

White-brown

Brown

Blue

TIA/EIA T

568 B

TP Wires

12345678

Pins:

68-3339-50 Rev. A

11 20

All trademarks mentioned are the property of their respective owners.

Worldwide Headquarters: Extron USA West, 1025 E. Ball Road, Anaheim, CA 92805, 800.633.9876

For information on safety guidelines, regulatory compliances, EMI/EMF compatibility, accessibility, and related topics, see the

Extron Safety and Regulatory Compliance Guide on the Extron website.

Application Diagrams

The following gures show typical applications for the DTP2 T 201 D transmitters.

TLP Pro 1520 TG

IN1808 IPCP SA

DTP2 R 211

Projector

IN1808 IPCP SA

INPUTS (DTP2/XTP)

LOOP OUT

4 6 7

SIG LINK

OUTPUTS (DTP2/XTP/HDBT) AUDIO INPUTS OUTPUTS REMOTE

HDMI/CEC

OVER TP

1A 1B

SIG LINK

OUT Tx Rx

LAN

AV LAN2 AV LAN3

AV LAN1

2x25W(8Ω)/2x50W(4Ω)

CLASS 2 WIRING

AMPLIFIED OUTPUT

Tx Rx

RTSCTS

Tx Rx GTxRxG

1234G

DIGITALI/OCOM 3COM 2COM 1

SSGG

2C34C -S G+S+V

PWROUT =6W

RRRRRRRRRR

IR/SERIALeBUSRELAYS

100-240V 50/60 Hz

--A MAX Tx Rx

RS-232

RESET

+48V

MIC/LINE

AUX

SCALING PRESENTATION SWITCHER

IN1808

CONFIG

1 2 3 4 5 6 7 8

INPUTS

LOGO

VOLUMEMIC

ENTER

eBUS

OVER

LIMIT

RTS

CTS

COM

IR/S

I/ORELAYS

INPUTS

SIGNAL

OUTPUTS

12345678 1ALOOP 1B

HDCP

DTP2

DTP

HOLDFOR 720p/1080p

Extron

DTP2 T 201 D

Transmitter

Ethernet

A Typical DTP2 T 201 D Application

Network

OUTPUTS

POWER

12V

1.3A MAX

SIG LINK

DTP2 IN

RS-232 IR

Tx Rx Tx RxG

AUDIO

OVER DTP2

CATx Cable

330 '

CATx Cable

330 '

HDMI

HDMI IN

LINK

100-240V ~ --A MAX

50-60 Hz

L IN RL OUT R

Tx Rx G

C T

C T G V+

RS-232

Tx Rx G

RESET

LAN

34 1A

HDMI/CEC

OUTPUTS

REMOTE

AUDIO

CONTACT

/TALLY

INPUTS

OVER TP

SIG

LINK

HDMI IN

LINK

CATx Cable

up to 330' (100 m)

Extron

DTP2 T 201 D

Transmitter

Extron

IN1804 DI

Receiver

RS-232

HDMI

Blu-ray Player

Flat Panel

Display

Otros manuales de Transmisor de Extron electronics

Extron electronics

Extron electronics DTP T HWP D Series Manual de usuario

Extron electronics

Extron electronics TP T 15HD AV Manual de usuario

Extron electronics

Extron electronics MTP 15HD A Series Manual de usuario

Extron electronics

Extron electronics DTP T EU 232 Manual de usuario

Extron electronics

Extron electronics DTP T USW 233 Manual de usuario

Extron electronics

Extron electronics DTP2 T 203 Manual de usuario

Extron electronics

Extron electronics DTP T HD2 4K 230 Manual de usuario

Extron electronics

Extron electronics XTP T HWP 101 Manual de usuario

Extron electronics

Extron electronics DTP3 T 101 D Manual de usuario

Extron electronics

Extron electronics PowerCage FOX 4G Tx VGA Manual de usuario

Extron electronics

Extron electronics DTP3 T 203 Manual de usuario

Extron electronics

Extron electronics DTP T UWP 4K 232 D Manual de usuario

Extron electronics

Extron electronics XTP T FB 202 4K Manual de usuario

Extron electronics

Extron electronics XTP T VGA Manual de usuario

Extron electronics

Extron electronics PVT CV D Manual de usuario

Extron electronics

Extron electronics A/V Receiver MTP 4T 15HD RS Manual de usuario

Extron electronics

Extron electronics DTP T HWP 232 D Manual de usuario

Extron electronics

Extron electronics DTP3 T 203 Manual de usuario

Extron electronics

Extron electronics DTP T DWP 4K D Series Manual de usuario

Extron electronics

Extron electronics DVI 201xi TX Manual de usuario

Extron electronics

Extron electronics XTP T HWP 101 Manual de usuario

Extron electronics

Extron electronics FOXBOX 4G Tx Manual de usuario

Extron electronics

Extron electronics DVI 201xi TX Manual de usuario

Extron electronics

Extron electronics PVT CV Manual de usuario

Manuales populares de Transmisor de otras marcas

NIVELCO

NIVELCO EasyTREK SCA-300 Series Manual del propietario

Honeywell

Honeywell 5816WMBR Manual de usuario

Kamstrup

Kamstrup READy MTU Instrucciones de funcionamiento

Omega

Omega ZW Series Manual de usuario

ABB

ABB Field 264H Guía

Alinco

Alinco DJ-V17T Manual de usuario

Dejero

Dejero EnGo 3x Manual de usuario

Rosemount

Rosemount 4600 Manual de usuario

Speaka Professional

Speaka Professional 2342740 Manual de usuario

trubomat

trubomat GAB 1000 Manual de usuario

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Manual de usuario

Rondish

Rondish UT-11 Manual de usuario

MG 10JRE Manual de usuario

Burkert

Burkert 8177 Manual de usuario

Firetide

Firetide HotPort 3203 Manual

Tele Radio

Tele Radio T9-02 Manual de usuario

Rotronic

Rotronic HygroFlex HF3 Series Manual de usuario

Jamara

Jamara FCX6 Pro Tel Manual de usuario