Extron electronics FOX3 Matrix 80x Manual de usuario

IMPORTANT:

Go to www.extron.com for the complete

user guide, installation instructions, and

specifications before connecting the

product to the power source.

IMPORTANT:

Go to www.extron.com for the

complete product specifications.

FOX3Matrix80x • Setup Guide

General Setup

The FOX3Matrix Switchers are congurable matrix switchers that distribute optical and audio signals. The FOX3 matrix is

primarily designed to support switching of FOX3 endpoints, FOX3 transmitters to FOX3 receivers. The matrix switcher routes any

input signal to any combination of outputs. The FOX3 matrix switcher can also route multiple input and output congurations

simultaneously (see gure1 for a FOX3Matrix80x conguration).

WARNING: The FOX3 matrix switcher fiber optic I/O boards output continuous invisible light, which may be harmful to the

eyes; use with caution. Do not look into the ber optic cable connectors or into the ber optic cables themselves. Plug the

attached dust caps into the optical transceivers when the ber cable is unplugged.

AVERTISSEMENT : Les cartes d’E/S fibre optique FOX3 matrix switcher émettent une lumière invisible continue, qui peut être

dangereuse pour les yeux ; à utiliser avec précaution. Ne pas xer directement les connecteurs optiques ou les câbles bre

optique. Branchez les protections contre la poussière dans l’ensemble émetteur/récepteur lorsque le câble bre optique est

débranché.

NOTE: FOX3 signals are not compatible with FOX and FOX II signals.

FOX3MATRIX CONTROL FOX3MATRIX AUDIO

DANTEEXPANSION

FANASSEMBLY

Tx G

1-4041-80

INPUTS/ OUTPUTS

AUDIOOUTPUTS

AUDIOINPUTS

RESET

RS-232

DMP

EXPANSION AT

LINK

AUDIOEXPANSION

DISCONNECTPOWER

CORDBEFORE

SERVICING

PRIMARY

50-60Hz

100-240V --AMAX

DISCONNECTPOWER

CORDBEFORE

SERVICING

REDUNDANT

50-60Hz

100-240V --AMAX

FOX3MATRIX 80X

LANREMOTE

FOX3MATRIX 8io

5OUTIN

OUT IN

6OUT

OUT IN

7OUTIN

OUT IN

8OUTIN

OUT IN

FOX3MATRIX 8io

5OUTIN

OUT IN

6OUTIN

OUT IN

7OUTIN

OUT IN

8OUTIN

OUT IN

FOX3MATRIX 8io

5OUTIN

OUT IN

6OUTIN

OUT IN

7OUTIN

OUT IN

8OUTIN

OUT IN

FOX3MATRIX 8io

5OUTIN

OUT IN

6OUTIN

OUT IN

7OUTIN

OUT IN

8OUTIN

OUT IN

FOX3MATRIX 8io

5OUTIN

OUT IN

6OUTIN

OUT IN

7OUTIN

OUT IN

8OUTIN

OUT IN

FOX3MATRIX 8io

5OUTIN

OUT IN

6OUTIN

OUT IN

7OUTIN

OUT IN

8OUTIN

OUT IN

FOX3MATRIX 8io

5OUTIN

OUT IN

6OUTIN

OUT IN

7OUTIN

OUT IN

8OUTIN

OUT IN

FOX3MATRIX 8io

5OUTIN

OUT IN

6OUTIN

OUT IN

7OUTIN

OUT IN

8OUTIN

OUT IN

FOX3MATRIX 8io

5OUTIN

OUT IN

6OUTIN

OUT IN

7OUTIN

OUT IN

8OUTIN

OUT IN

FOX3MATRIX 8io

5OUTIN

OUT IN

6OUTIN

OUT IN

7OUTIN

OUT IN

8OUTIN

OUT IN

FOX3MATRIX 8io

5OUTIN

OUT IN

6OUTIN

OUT IN

7OUTIN

OUT IN

8OUTIN

OUT IN

100-240V 0.7AMAX

50-60Hz

FOX3 R 301

HDMI LAN

OUT

IN OUT IN

INPUTS

CONTROL

AUDIO

RETURN

REMOTE

OUTPUTS

SYNC

AUDIO

RS-232

Rx TxRxG

Tx Rx G S 5V

100mA

2 1

500mA

USB2.0

USBHID

DEVICES

100-240V 0.7AMAX

50-60Hz

FOX3 R 301

HDMI LAN

OUT

IN OUT IN

INPUTS

CONTROL

AUDIO

RETURN

REMOTE

OUTPUTS

SYNC

AUDIO

RS-232

Rx TxRxG

Tx Rx G S 5V

100mA

2 1

500mA

USB2.0

USBHID

DEVICES

100-240V 0.7AMAX

50-60Hz

FOX3 T 301

HDMI

USB HID

HOST HOST

USB 2.0 LAN

OUT

IN OUT IN

LOOP OUT

OUTPUTS

CONTROL

AUDIO

RETURN

REMOTE

INPUTS

SYNC

AUDIO

RS-232

Rx Tx RxG

Tx Rx G S 5V

100-240V 0.7AMAX

50-60Hz

FOX3 T 301

HDMI

USB HID

HOST HOST

USB 2.0 LAN

OUT

IN OUT IN

LOOP OUT

OUTPUTS

CONTROL

AUDIO

RETURN

REMOTE

INPUTS

SYNC

AUDIO

RS-232

Rx Tx RxG

Tx Rx G S 5V

100-240V 0.7AMAX

50-60Hz

FOX3 T 301

HDMI

USB HID

HOST HOST

USB 2.0 LAN

OUT

IN OUT IN

LOOP OUT

OUTPUTS

CONTROL

AUDIO

RETURN

REMOTE

INPUTS

SYNC

AUDIO

RS-232

Rx Tx RxG

Tx Rx G S 5V

100-240V 0.7AMAX

50-60Hz

FOX3 T 301

HDMI

USB HID

HOST HOST

USB 2.0 LAN

OUT

IN OUT IN

LOOP OUT

OUTPUTS

CONTROL

AUDIO

RETURN

REMOTE

INPUTS

SYNC

AUDIO

RS-232

Rx Tx RxG

Tx Rx G S 5V

1.2AMAX

100-240V~ 50-60Hz

PWROUT = 12W

+V +S -S G

2 3 7

5 6 8

S G S G S G S GTx Rx G Tx Rx G TxRx G TxRx G

RTSCTS

1 2 1 2 3 41 2 3 4

321 4 G

Tx Rx G Tx Rx G TxR x G Tx Rx G

RTS

CTS

SGSG SGSG

5 6 7 8 5 6 7 8

SWITCHED12 VDC

40WMAX TOTAL

3 4

COM

eBUS

FLEX I/ORELAYSIR/SERIAL

12 VDC

LAN

MODEL80

FLATPANEL

MODEL80

FLATPANEL

TLP Pro 725M

7" Wall Mount Touchlink

Pro Touchpanel

FOX3 T 301

Fiber Optic Transmitter

for HDMI 4K Display

USB Headset

Keyboard

Mouse

Ethernet

4K HDMI

USB

FOX3 T 301

Fiber Optic Transmitter

for HDMI

4K HDMI

USB

FOX3 T 301

Fiber Optic Transmitter

for HDMI

4K HDMI

USB

FOX3 T 301

Fiber Optic Transmitter

for HDMI

Computer

4K HDMI

USB

RS-232

4K HDMI

Fiber

USB

Ethernet

FOX3 R 301

Fiber Optic Receiver

for HDMI

4K Display

USB Headset

Keyboard

Mouse

RS-232

4K HDMI

USB

FOX3 R 301

Fiber Optic Receiver

for HDMI

IPCP Pro 555

IP Link Pro Control

Processor

FOX3 Matrix 80x

Modular Fiber Optic

Matrix Switcher

AV Control

Network

Figure 1. Typical FOX3Matrix80x Application

FOX3 Matrix 80x • Setup Guide (Continued)

The Extron proprietary ber optic signal, generated by Extron ber optic transmitters, can include video, stereo audio, USB 2.0,

USB HID, return audio, IR, 3D sync, and transmitter-to-receiver RS-232 serial communications.

The matrix switcher can be remotely controlled via the rear panel Ethernet LAN port, rear panel RS-232 port (SIS only), or front

panel USB port, using either the Windows®-based Extron Product Conguration Software (PCS) or Simple Instruction Set (SIS)

commands.

NOTES:

• Compatible optical signals are digital signals up to 10 Gbps that are sent and received via fiber optic small form factor

pluggable (SFP) modules.

• The FOX3 transmitter-to-receiver communications, including the serial link, occupy one matrix switcher input and

output. This matrix switcher supports the insertion, through the LAN port, of serial (pass through) communications from

the matrix to the FOX3 transmitter or the FOX3 receiver.

The switcher has two hot-swappable 100 VAC to 240 VAC, 50-60 Hz power supplies that provide worldwide power compatibility

and reliability.

Conﬁgurability and Transmission modes

The FOX3Matrix Switchers are assembled from individual input/output (I/O) boards. The switcher can include up to 10 I/O

boards, each supports up to 8 inputs and 8 outputs. The two types of I/O boards are:

• Singlemode (SM) fiber optic 8x8 I/O board — Very long distance, up to 20 km (12.43 miles)

• Multimode (MM) fiber optic 8x8 I/O board — Long distance, up to 500 m (1640 feet)

Increase or decrease the size of the FOX3Matrix 80x Switcher from an 8-input by 8-output matrix to an 80-input by 80-output

matrix by adding or removing I/O boards.

NOTE: Multimode and singlemode fiber optic I/O boards can be mixed in a FOX3Matrix switcher, but it is imperative to

connect the proper transmission mode fiber cables to the board.

Rear Panel

As shown in gure2, each I/O board is identied by the input and output numbers supported by the board position. The board

position designators, printed beside the fan, correspond to the input and output numbers served by that position (1 - 40, 41 - 80).

WARNING: This unit outputs continuous invisible light, which may be harmful to the eyes; use with caution. For additional

safety, plug the attached dust caps into the optical transceivers when the fiber cable is unplugged.

AVERTISSEMENT : L’appareil émet une lumière invisible en continu, à utiliser avec précaution. Pour une sécurité renforcée,

associez les bouchons anti-poussière à l’ensemble émetteur/récepteur optique lorsque le câble fibre optique est

débranché.

PRIMARY

FOX3 MATRIX 80x

AUDIO EXPANSION

DMP

EXPANSION

LINK

AUDIO OUTPUTS

AUDIO INPUTSS

FOX3 MATRIX

CONTROL

FAN ASSEMBLY

Extron

INPUTS / OUTPUTS

LINK

FOX3 MATRIX AUDIO

DANTE EXPANSION

50/60Hz

100-240V ~x.xA MAX. 100-240V ~x.xA MAX.

DISCONNECT POWER

CORD BEFORE

SERVING

DISCONNECT POWER

CORD BEFORE

SERVING

REDUNDANT

1 - 40

41 - 80

RESET Tx Rx G

RS-232

LAN

REMOTE

OUT IN

OUT

IN 8

OUT IN

OUT

IN 7

OUT IN

OUT

IN 6

OUT IN

OUT

IN 5

FOX3 MATRIX 8io

OUT IN

OUT

IN 8

OUT IN

OUT

IN 7

OUT IN

OUT

IN 6

OUT IN

OUT

IN 5

FOX3 MATRIX 8io

OUT IN

OUT

IN 8

OUT IN

OUT

IN 7

OUT IN

OUT

IN 6

OUT IN

OUT

IN 5

FOX3 MATRIX 8io

OUT IN

OUT

IN 8

OUT IN

OUT

IN 7

OUT IN

OUT

IN 6

OUT IN

OUT

IN 5

FOX3 MATRIX 8io

OUT IN

OUT

IN 8

OUT IN

OUT

IN 7

OUT IN

OUT

IN 6

OUT IN

OUT

IN 5

FOX3 MATRIX 8io

OUT IN

OUT

IN 8

OUT IN

OUT

IN 7

OUT IN

OUT

IN 6

OUT IN

OUT

IN 5

FOX3 MATRIX 8io

OUT IN

OUT

IN 8

OUT IN

OUT

IN 7

OUT IN

OUT

IN 6

OUT IN

OUT

IN 5

FOX3 MATRIX 8io

OUT IN

OUT

IN 8

OUT IN

OUT

IN 7

OUT IN

OUT

IN 6

OUT IN

OUT

IN 5

FOX3 MATRIX 8io

OUT IN

OUT

IN 8

OUT IN

OUT

IN 7

OUT IN

OUT

IN 6

OUT IN

OUT

IN 5

FOX3 MATRIX 8io

OUT IN

OUT

IN 8

OUT IN

OUT

IN 7

OUT IN

OUT

IN 6

OUT IN

OUT

IN 5

FOX3 MATRIX 8io

GGG

GGGG

GGGG HHH

HHHH

HHHH III

IIII

IIII JJJK K K

BBB

BBBB

FFF

FFFF

AAA

AAAA

CCC

CCCC

DDD

DDDD

EEE

EEEE

FFF

FFFF

Figure 2. FOX3 Matrix 80x Switcher Rear Panel

AFiber optic boards with connectors and LEDs

BReplaceable fans

CLAN Ethernet port

DRemote RS-232 port

EReset button and LED

FPower supplies

GPower connectors

HAudio Inputs

IAudio Outputs

JDMP Expansion port and LED

KDante Expansion ports

Rear Panel Overview

AFiber optic boards with connectors and LEDs — (see figure2 on page2)

NOTES:

• Ensure the proper fiber cable for the I/O board is used. Typically, singlemode fiber has a

yellow jacket and multimode cable has an orange or cyan jacket.

• The FOX3 matrix switcher uses one connector on the block as an input and the second

connector on the same block as a separate output.

1 Input connector — Connect a fiber optic cable between each Input LC connector and a FOX3

transmitter or any other compatible Extron FOX device.

NOTE: For USB, return audio, and serial RS-232 (receiver-to-transmitter) function, connect

the far end to the Optical Out connector on a FOX receiver.

Input LED — See Fiber optic I/O board LED indication on page4.

2 Output connector — Connect a fiber optic cable between each output LC connector and a

FOX3 receiver or any other compatible Extron FOX device (see figure1 on page1).

NOTE: For USB, return audio, and serial RS-232 (receiver-to-transmitter) function, connect

the far end to the Optical In connector on a FOX transmitter.

Output LED — See Fiber optic I/O board LED indication on the next page.

BReplaceable fans — This fan card has 3 removable fans (see Removing and Installing a Fan

Module on page12 to replace a fan).

CLAN Ethernet port — Optionally, connect a network WAN or LAN hub, a control system, or a

computer to the Ethernet RJ-45 port.

• Network connection — Wire as a patch (straight) cable.

• Computer or control system connection — Wire the interface cable as a crossover cable.

DRemote RS-232 port — Optionally, connect a control system or computer to the rear panel Remote

RS-232 port (see figure3 for wiring).

RS-232

Tx Rx G

REMOTE

TransmitReceive

ReceiveTransmit

GroundGround

DB9 Pin Locations

Female

Pin 2 = Rx

Pin 3 = Tx

Pin 5 = G

Computer

Figure 3. RS-232 Connector Wiring

EReset button and LED — Initiate four levels of reset of the matrix switcher. For different reset levels, press and hold the

recessed button while the switcher is running or while powering up the switcher (see the FOX3 80x User Guide, available at

www.extron.com for more information on the reset modes).

NOTE: The factory configured passwords for all accounts on this device have been set to the device serial number.

In the event of a complete system reset, the passwords convert to the default, which is extron for the Admin and no

password for the User.

FPower supplies — The Primary and Redundant power supplies are hot-swappable. There are two corresponding LEDs on

the front panel that indicate the status of each power supply (see Removing and Installing a Power Supply Module on

page12 to replace power supplies).

GPower connectors — Plug the switcher into two grounded AC sources.

NOTE: For reliability, connect the Redundant power cord to either an uninterruptible power source or to a power source

that is completely independent from the primary power source.

OUT IN

Optional for

return data

OUTPUTS

Transmitting

Unit

Receiving

Unit

FOX3 Matrix

Switcher

IN*

*Optional for

return data

OUT

INPUTS

OUT*

2211

FOX3 Matrix 80x • Setup Guide (Continued)

HAudio Inputs (see figure2 on page2) — Connect

audio input devices to an audio 5-pole captive screw

port (see figure4 to wire the captive screw connector).

IAudio Outputs — Connect audio output devices to an

audio 5-pole captive screw port (see figure4 to wire the

captive screw connector).

Unbalanced Stereo Input Balanced Stereo Input

Do not tin the wires!

Tip

Ring

Tip

Ring

Sleeves

Tip

Sleeve

Tip

Unbalanced Stereo Output Balanced Stereo Output

Do not tin the wires!

Tip

No Ground Here

Tip

Sleeves

Tip

Ring

Tip

Ring

Sleeves

Figure 4. Audio Input Wiring Diagram

JDMP Expansion port and LED —

• Expansion Port — Connect an STP cable between this port and the Expansion port on an optional Extron DMP Digital

Matrix Processor for digital audio connection. Receive and transmit eight 2-channel stereo inputs and eight 2-channel

stereo outputs via this RJ-45 connection.

• Link LED — Lights to indicate that the port is connected to a compatible device.

NOTE: Only connect Extron non-AT audio devices to the DMP Expansion port.

KDante Expansion ports — Connect RJ-45 connectors to external Dante devices for digital audio networking. Receive and

transmit 32 2-channel inputs and 32 2-channel outputs via these two RJ-45 connections.

Fiber optic I/O board LED indication

On the fiber optic I/O boards, the input and output LEDs on the transceivers

light green when 10G light is detected. The arrow LEDs point to the input and

output port they represent.

In figure5, SFP 1 and SFP 5 are examples of the LEDs that indicate the input

and output port (different colors are used to indicate the connection only).

• Out 1 is red and the corresponding arrow LED is red.

• In 1 is blue and the corresponding arrow LED is blue.

• Out 5 is purple and the corresponding arrow LED is purple.

• In 5 is green and the corresponding arrow LED is green.

OUT IN

OUT

IN 8

OUT IN

OUT

IN 7

OUT IN

OUT

IN 6

OUT IN

OUT

IN 5

FOX3 MATRIX 8io

Figure 5. Fiber Optic I/O Board LEDs

Front Panel

FOX3 MATRIX 80x

PRIMARY REDUNDANT

FIBER OPTIC DIGITAL MATRIX SWITCHER

Extron

POWER

CONFIG

AAABBB

Figure 6. FOX3Matrix80x Switcher Front Panel

AUSB Config port — If desired, connect computer to the front panel Configuration port.

BPrimary and Redundant Power Supply LEDs — Light to indicate the power supply status.

• Green — Indicates that the associated power supply is operating within normal tolerances.

• Red — Indicates that the associated power supply is operating outside the normal tolerances, there is no AC connected

to the power supply, or the power supply has failed (see Removing and Installing a Power Supply Module on

page12 to replace the power supply).

• Unlit — Indicates that the power supply is not connected.

Matrix Operations

The FOX3 Matrix 80x can be operated in one of two modes: Port mode and System Map mode.

NOTE: The FOX3 matrix is initially in Port mode when it is powered for the first time.

• In Port mode, each physical SFP on the Matrix represents an individual In 1 and Out 1.

• In System Map mode, multiple SFP modules can be combined via PCS to create a configuration map. This mode is used to

simplify system switching and USB group switching.

Remote Control

This section describes using the remote control features of the FOX3Matrix switchers to control the devices.

Use Simple Instruction Set (SIS) commands for operation and conguration of the matrix. Run these commands from a PC

connected to:

• A LAN or WAN using the rear panel RJ-45 LAN connector (see figure2,C on page2) via PuTTY and port 22023.

• The Remote RS-232 port (see figure2,D) via DataViewer.

• The front panel USB config port (see figure6,A on page4) via PuTTY and IP address 203.0.113.22 and port 22023.

NOTE: The table below is a partial list of SIS commands. For a complete listing of commands and instructions to install

PuTTY, see the FOX3Matrix80x User Guide.

Command and Response Table for SIS Commands

Command ASCII Command

(Host to Unit)

Response

(Unit to Host)

Additional Description

NOTE: Commands can be entered back-to-back in a string, with no spaces. For example: 1*1!002*002!003*003!.

Output switching

NOTES:

• The quick multiple tie and tie input to all output commands activate all I/O switches simultaneously.

• The !tie command, &tie command, and %tie command can be used interchangeably.

• The !tie all command, &tie all command, and %tie all command can be used interchangeably.

• When you create a tie where X! = 00, you tie no input to the specied output (X@) (untie X@).

• When you create a tie where X@ = 00, you untie all outputs from input X!.

• If a System Map has been initiated, the Input number (X!) or Output number (X#) can represent a single physical SFP port or a group of

SFP ports.

Tie input X! to output X# X!*X#! OutX#•InX!•All]Tie input X! to output X#, all signals.

Tie input X! to output X# X!*X#% OutX#•InX!•Vid]Tie input X! to output X#, video only.

Tie input X3% to output X3^ X3%*X3^$ OutX3^•InX3%•Aud]Tie input X! to output X#, audio.

Tie return audio source X3&

to destination X3*

X3&*X3*& OutX3*•InX3&•Rta]Tie return audio source to destination.

TIP: 0*! clears all ties.

KEY: X! = Input number 00 – Maximum number of inputs for your configuration (0= untied)

X# = Output number 00 – Maximum number of outputs for your configuration (0= untied)

X3% = Audio input number 00 – Maximum number of inputs or Expansion 30001-30008, Dante 40001-40032,

Analog 50001-50004

X3^ = Audio output number 00 – Maximum number of outputs or Expansion 30001-30008, Dante 40001-40032,

Analog 50001-50004

X3& = Return audio source number 00 – Maximum number of outputs (from an Rx unit, Expansion 30001-30008,

Dante 40001-40032, or Analog 50001-50004)

X3* = Analog audio destination number (to Tx) 00 – Maximum number of inputs

FOX3 Matrix 80x • Setup Guide (Continued)

Command ASCII Command

(Host to Unit)

Response

(Unit to Host)

Additional Description

Tie an input to all outputs

Tie input to all outputs X!*! InX!•All]Tie video and audio input, 3D sync and IR

signals to all outputs.

NOTE: USB 2.0, USB HID, and Return Audio are not switched with this command

Tie input to all outputs X!*% InX!•Vid]Tie video input to all outputs.

Tie input to all outputs X!*$ InX!•Aud]Tie audio input to all outputs.

KEY: X! = Input number 00 – Maximum number of inputs for your configuration (00 = untied)

Untie

Untie all outputs 0*! In00 All]Untie all outputs.

Untie an output 0* X#! Out X#•In00 •All]Untie a particular output.

Untie an input X#*0! Outx00•InX# •All]Untie an input from all tied outputs.

KEY: X# = Output number 00 – Maximum number of outputs for your configuration (00 = untied)

Quick tie

NOTES:

• The Quick multiple tie and tie input to all outputs commands activate all I/O switches simultaneously.

• The matrix switcher support 3-digit numeric (001*001) and 5- digit for audio ties (50001*50001)

• The Quick tie applies to ber I/O, audio expansion, Dante, or analog audio sections.

• Commands can be made back to back with no spaces.

Quick multiple tie E+QX!*X#!...X!*X#!}Qik]or

Qik14]

Make multiple ties.

Qik14 responds back when part of the

command is invalid or incorrect.

KEY: X! = Input number 00 – Maximum number of inputs for your configuration (00 = untied)

X# = Output number 00 – Maximum number of outputs for your configuration (00 = untied)

Matrix Status

Request Information I/i

Verbose mode 2/3

VX2*XX2*•AX!XX3% •SX^ 1

XX^ 2... X^n]

Inf00* VX2*XX2*•AX!XX3% •SX^ 1

XX^ 2... X^n]

Slot/LC connector

information

0*X&I

Verbose mode 2/3

X1*X1*X1* X1* X1*X1* X1* X1*]

Inf*X1*X1*X1* X1* X1*X1*X1* X1*]

Request part number N/n 60-nnnn-nn]

View power supply voltages,

unit temperature, fan speeds

and Power Supply status

S/s X2$p

•X2$ R•X2%•X2^1•X2^ 2•X2^ 3...•X2^n

•X2&P

•X2&R]

Sts00 •X2$p

•X2$ R•X2%•X2^1•X2^ 2•X2^ 3...•X2^n

•X2&P

•X2&R]

View temperature of the unit E20STAT}

Verbose mode 2/3

X2%]

20StatX2%]

View status of power

supplies (Primary,

Redundant)

E21STAT}

Verbose mode 2/3

X2$P

•X2$R]

21StatX2$P

•X2$R]

View fan speeds E22STAT}

Verbose mode 2/3

X2^1•X2^2•X2^ 3...•X2^ n] 80x has 3 fans

22StatX2^1•X2^2•X2^ 3...•X2^ n]

KEY: X! = Input number 00 – Maximum number of inputs for your configuration (00 = untied)

X^ = I/O board type 0= No board detected, 1= Active MM board, 2= Active SM board, 3= Passive MM board,

4= Passive SM board, 5= Unknown

X& = I/O board slot number 1– maximum number of slots (10 for 80x)

X1* = SFP modules installed 0= No SFP, 1= MM SFP, 2= SM SFP, 3= Unknown SFP

X2$ = Power supply voltage P = Primary, R = Redundant

X2% = Temperature Degrees in Fahrenheit and Celsius (example: xx.xF • xx.xC)

X2^ = Fan speed Revolutions per Minute (RPM) (example: xxxRPM

X2& = Power supply status 0= Power Supply inactive/Not installed, 1= Power Supply active/Installed,

2= Power Supply failed/Installed

X2* = Maximum virtual video matrix size inputxoutput (example: 80x80)

X3% = Audio input number 00 – Maximum number of inputs or Expansion 30001-30008, Dante 40001-40032,

Analog 50001-50004

Command ASCII Command

(Host to Unit)

Response

(Unit to Host)

Additional Description

View individual video input

signal status

EX!LS}

Verbose mode 2/3

X1(]

InX!•X1(]

View all video input signal

status

E0LS}

Verbose mode 2/3

X1(1

X1( 2... X1(n]

In00X1(1

X1( 2... X1(n]

Each response is the video input status,

starting from Input 1 and n= highest

numbered installed input.

KEY: X! = Input number 00 – Maximum number of inputs for your configuration (00 = untied)

X1( = Video signal status 0= No video signal at input, 1= Video Input signal detected

Verbose Mode

Set verbose mode EX2)CV}VrbX2) ]

View verbose mode ECV} X2)]

NOTE: Verbose mode will revert back to default in the event of a power cycle, disconnect from dataviewer, or disconnect from the Ethernet.

KEY: X2) = Verbose mode 0= Clear/none, 1= Verbose mode (default), 2= Tagged response for queries,

3= Verbose mode and tagged responses for queries

Product Conﬁguration Software (PCS)

Another way to operate the switcher is via Product Conguration Software (PCS), which runs on computers that use the

Windows®operating system. This program is available on the Extron website. PCS can be run from a PC connected to the rear

panel LAN port (see ﬁgure2, C) or front panel conguration port (see ﬁgure6, Aon page4) on the switcher.

NOTE: For details on operating PCS, see the FOX3Matrix80x Help file.

Installing the Program

Download and install all programs as follows:

1. Go to www.extron.com and mouse over the Download

tab (see figure7, 1).

2. Click the PCS Product Configuration Software

link (2). The PCS Product Configuration Software

page opens.

3. Click Download (see figure8, 1).

TIP: Jump to the nearest page of downloads

by clicking the desired filtering letter. Figure 7. Download Drop-down List

The download warns about downloads and asks to conrm

the download.

4. Click Run to confirm that you want to run the installation.

5. Follow the on-screen instructions. The installation program

creates the necessary directories and folders and installs the

program. Figure 8. Download Center Dialog Box

FOX3 Matrix 80x • Setup Guide (Continued)

Connecting to PCS

The Extron Product Conguration Software window opens to the Device Discovery panel. Connect to the FOX3 Matrix using the

Device Discovery panel or the TCP/IP panel (see gure9).

1. Open the Product Configuration Software program from the desktop shortcut.

The Extron PCS window opens to the Device Discovery panel (see gure9).

Figure 9. Device Discovery Panel

2. Select the FOX3 Matrix 80x device by clicking on it to highlight it in the list (1).

3. Click Connect (2). The FOX3 Matrix 80x PCS main page opens (see gure10).

Figure 10. FOX3 Matrix 80x PCS Main Page

To edit the IP address:

1. Click on the Edit button (see figure9, 3on page8). The

Communication Settings box opens.

2. Click in the field to edit (see figure11) .

3. Click Apply to complete and close.

Alternatively, click Apply and Connect to complete and connect to the

device.

Click Cancel to close the box without changes.

Figure 11. Communication Settings Box

Internal Web Pages

Another way to congure and operate the switcher is via its factory-installed internal web pages. The pre-loaded web pages on

the switcher are accessible through the LAN port (see ﬁgure2,C on page2) via a LAN or WAN connection or the front panel

USB cong port (see ﬁgure6,A on page4) using a web browser such as Microsoft®Internet Explorer®.

Disabling Compatibility Mode

The internal web page does not support compatibility mode in Microsoft Internet Explorer.

To check compatibility view settings:

1. From the Tools menu of the browser, select Compatibility View Settings. The Compatibility View Settings dialog box

opens.

2. Be sure the Display all websites in Compatibility View checkbox is clear, and the IP address of the matrix is not in the

list of websites that have been added to Compatibility View.

Accessing the Internal Web Page

Access the FOX3 Matrix internal web page as follows:

1. Connect the FOX3 Matrix to a LAN or WAN using the rear panel RJ-45 LAN connector (see ﬁgure2,C) or the front panel

USB cong port (see ﬁgure6,A on page4).

2. Open a web browser on a connected PC.

3. Enter the FOX3 Matrix IP address in the browser Address field.

NOTES:

• If the local system administrators have not changed the value, the factory specified default for the LAN or WAN

connection is 192.168.254.254.

• The default for the USB connection is 203.0.113.22 (this IP address cannot be changed).

4. Press the <Enter> key on the keyboard.

5. The FOX3 Matrix is password protected. Enter a user name (user or admin) in the Username field and the password in the

Password field when prompted (see figure12 on page10).

NOTE: The factory configured passwords for all accounts on this device have been set to the device serial number. In

the event of a complete system reset, the passwords convert to the default. The default username is admin and the

password is extron.

FOX3 Matrix 80x • Setup Guide (Continued)

Figure 12. Network Password Prompt

6. Click the Sign in button. The internal web page opens (see figure13).

Figure 13. Internal Web Main Page

NOTE: For detailed information about the internal web page, see the FOX3 Matrix 80x User Guide available at

www.extron.com.

Otros manuales para FOX3 Matrix 80x

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Conmutador de matriz de Extron electronics

Extron electronics

Extron electronics DTP CrossPoint 4K Series Manual de usuario

Extron electronics

Extron electronics HDXP Plus Series Manual de usuario

Extron electronics

Extron electronics MAV Series Manual de usuario

Extron electronics

Extron electronics MPX 423 A Manual de usuario

Extron electronics

Extron electronics MAV Plus Series Manual de usuario

Extron electronics

Extron electronics DXP HD 4K Series Manual de usuario

Extron electronics

Extron electronics XTP II CrossPoint Series Manual de usuario

Extron electronics

Extron electronics CrossPoint 42 HVA Manual de usuario

Extron electronics

Extron electronics CrossPoint 450 Plus 64 Series Manual de usuario

Extron electronics

Extron electronics SMX Series Manual de usuario

Extron electronics

Extron electronics XTP CrossPoint1600 Manual de usuario

Extron electronics

Extron electronics Crosstalk 1632 Manual de usuario

Extron electronics

Extron electronics DXP 1616 HD 4K PLUS Series Manual de usuario

Extron electronics

Extron electronics Matrix 50 Series Manual de usuario

Extron electronics

Extron electronics FPC 5000 Manual de usuario

Extron electronics

Extron electronics Matrix 50 Series Manual de usuario

Extron electronics

Extron electronics DXP DVI Pro Manual de usuario

Extron electronics

Extron electronics TPX 88 Series Manual de usuario

Extron electronics

Extron electronics SW HD 4K PLUS Series Manual de usuario

Extron electronics

Extron electronics FOX3 Matrix Series Manual de usuario

Extron electronics

Extron electronics FOX 4G Matrix 14400 Manual de usuario

Extron electronics

Extron electronics MMX 32 VGA A Manual de usuario

Extron electronics

Extron electronics MPX 423 A Manual de usuario

Extron electronics

Extron electronics CrossPoint 300 Series Manual de usuario

Manuales populares de Conmutador de matriz de otras marcas

Broadcast Tools

Broadcast Tools SS 8.2 Manual de usuario

Altimium

Altimium MATF32 Manual de usuario

ALFAtron

ALFAtron ALF-MUK44N Manual de usuario

Monoprice

Monoprice Blackbird 15377 Manual de usuario

Kramer

Kramer XL 3216VS Manual de usuario

PTN

PTN FMX12 Manual de usuario

CYP

CYP nT15GX01 Manual de usuario

Kramer

Kramer VP-2x2 Manual de usuario

Kramer

Kramer Sierra Video 6432V5xl Manual de usuario

TESmart

TESmart HMA0402A40 Manual de usuario

Octava

Octava HD4XSTPMX Manual de usuario

Intelix

Intelix FLX-88 Instrucciones de funcionamiento

Kramer

Kramer LASSEN XL 3232S Manual de usuario

Roland

Roland XS-1HD Manual de usuario

Kramer

Kramer VS-66HDCPxl Manual de usuario

Atlona

Atlona AT-HDMI-22M Manual de usuario

Link

Link HD8X8 Manual de usuario

AMX

AMX AVS-OP-2020-117 Instrucciones y recetas