Extron electronics MMX 32 VGA MTP Manual de usuario

This guide provides basic instructions for an experienced installer to set up and operate the

Extron® MMX 32 VGA MTP mini matrix switcher.

N For full installation and operating details, refer to the MMX 32 VGA MTP Users’s Guide,

available online at www.extron.com.

Installation

Step 1 — Mounting

Turn off or disconnect all equipment power sources and mount the MMX 32 VGA MTP as

required (rack, furniture, or tabletop mounted).

Step 2 — Connect inputs

Connect up to three video sources (RGBHV, RGBS, RGsB, RsGsBs,

component video, S-video or composite video) to the female 15-HD

connectors, inputs 1-3.

Connect audio sources to the 3.5 mm stereo jacks and wire the audio

connectors as shown at right.

Step 3 — Connect outputs

Attach the applicable output cables (video, audio, and video and audio) as below:

a. Video output 1 — Connect a display device to this female 15-pin HD connector.

b. Audio output 1 — Connect speakers to this 3.5 mm stereo jack.

c. Audio/Video (RGB) output 2 — Connect an MTP U R series or other MTP receiver

to this RJ-45 UTP connector.

Wire the connector as shown at right.

Connect a projector or other RGB video

output device to the receiver, and

connect speakers for summed (L and R)

mono audio output.

d. Audio output 2 — Connect speakers

to this 5-pole, 3.5 mm captive screw

connector for balanced/unbalanced

audio and wire connector for dual mono

output as shown below.

MONO AUDIO

Unbalanced Output Balanced Output

Do not tin the wires!

Mono output 1-

Sleeve(s)

Mono output 1+

Mono output 2+

Mono output 2-

Sleeve(s)

Mono output 1

Mono output 2

NO GROUND.

For unbalanced audio, connect both sleeves to the center (ground)

contact. DO NOT connect the sleeves to the negative (-) contacts.

Setup Guide — MMX 32 VGA MTP

NOTE If you are using Enhanced Skew-Free™ A/V

cable, use the TIA/EIA T568A standard only.

Insert Twisted

Pair Wires

Pins:

12345678

RJ-45 Connector

1 Red+/V. sync+

2 Red–/V. sync–

3 Mono audio+

Green–

6 Mono audio–

7 Blue+/H. sync+

8Blue–/H. sync–

Wire color

White-green

Green

White-orange

White-blue

Orange

White-brown

Brown

Wire color

568 A 568 B

Signal

White-orange

Orange

White-green

White-blue

Green

White-brown

Brown

Green+Blue Blue

L R

INPUT 2

INPUT 1

AUDIO

OUTPUT 1

AUDIO

INPUT 3

AUDIO

REMOTE

AUDIO

MMX 32 VGA MTP

OUTPUT 1

2 1 3

OUTPUT 2

2 1 3

RS-232

+5V

POWER

12V

0.5A MAX

1 2 3

CONTACT

Tx Rx

SYNC - TRI

PRE PEAK - ON

OUTPUT 2

RGB/AUDIO

Sleeve ( )

Ring (R)

Tip (L)

3.5 mm TRS Stereo

Plug Connector

(unbalanced)

Step 4 — Remote connections

a. Contact closure connectors — Connect an Extron

MMX 32 AAP or MMX 32 MAAP contact closure

remote control panel to these two 5-pole captive

screw connectors to provide control for outputs

1 and 2. Connect the 5 V and Gnd (-) 2-pole captive

screw connector on the AAP or MAAP to either of

these connectors.

b. RS-232 connector — Connect an RS-232 control module to this 3-pole captive screw

connector (see image above) to allow remote control using the Extron Simple Instruction

Set™(SIS™) or the Extron Universal Switcher Control Program.

N For full SIS commands and details of the Universal Switcher Control Program, refer to the

MMX 32 VGA MTP Users’s Guide.

Step 5 — Power

Plug the included external 12 VDC power supply into the 2-pole

captive screw connector. Wire the connector as shown at right.

Step 6 — Pre-Peaking and sync selection

Pre-Peaking — To compensate for signal loss over long cable runs, set the DIP

switch position (up = on, down = off) as shown in the table below:

Video Format Cable length Signal quality at max.

distance

Pre-Peak Off Pre-Peak On High Variable

Composite, S-video,

Component

800 ft (245 m) 1000 ft (300 m)

640 x 480 <300 ft (90 m) >350 ft (105 m) 700 ft (215 m) 750 ft (230 m)

800 x 600 <300 ft (90 m) >350 ft (105 m) 550 ft (165 m) 650 ft (200 m)

1024 x 760 <300 ft (90 m) >350 ft (105 m) 500 ft (150 m) 600 ft (185 m)

1280 x 1024 <250 ft (75 m) >300 ft (90 m) 350 ft (105 m) 450 ft (135 m)

1600 x 1200 <250 ft (75 m) >300 ft (90 m) 300 ft (90 m) 450 ft (135 m)

Sync selection — To select either bi-level sync or tri-level sync on output 2, set the sync DIP

switch to the desired setting (up = tri-level sync, down = bi-level sync).

N Set when transmitting tri-level sync component video.

SECTION A–A

A A

Power Supply

Output Cord

Ridges

Smooth

3/16"

(5 mm) Max.

2-Pole Captive

Screw Connector

Tie Wrap

Setup Guide — MMX 32 VGA MTP cont’d

REMOTE

RS-232

+5V

1 2 3

Tx Rx

CONTACT

Output 1 control

Output 2 control

RS-232

connection

SYNC - TRI

PRE PEAK - ON

Front Panel Operation

Outputs 1 and 2 — For each output press the button for the desired input (1, 2 or 3). The

LED for that input lights.

N When power is applied, the LEDs light sequentially from left to right. For ﬁrst time power

up, the unit’s default conﬁguration is input 1 tied to both outputs 1 and 2, the front panel is

not locked, and all states are unmuted. Input 1 LEDs for output 1 and for output 2 are both

lit. If this is not a ﬁrst time power up, then the LEDs for the last valid input selections light.

Front panel security lock out (executive mode)

Locking the front panel protects the switcher from unwanted tampering. While the switcher is

locked, the user can select inputs only through a remote device.

To lock or unlock the front panel, press the following buttons simultaneously and hold them

for at least 3 seconds:

• For output 1 press and hold input 1 button. • For output 2 press and hold input 3 button.

The front panel LEDs ﬂash to indicate that the

front panel is locked.

System reset

To reset the switcher to its factory settings, press and hold output 1’s input 3 button while

powering up the switcher.

Audio switching

When you selecting an input, the audio and video signals from that input are routed together

to the appropriate output.

Audio breakaway is possible through the Extron Simple Instruction Set (SIS) or the Extron

Universal Switcher Control Program. When audio breakaway is active, the front panel input

LED for the audio source ﬂashes, while the LED of the video source lights steadily.

Device Control

Output control

Momentarily short the rear panel Remote contact pin 1, 2, or 3 for the desired output to ground

to switch to that input.

Use the +5 V port when controlling the output with an MMX 32 AAP/MAAP panel.

RS-232 Control

Software control via the RS-232 connection is possible using the Extron Simple Instruction Set

(SIS) or the Extron Windows®-based control program.

The RS-232 connector on the MMX 32 VGA MTP is a 3-pole captive screw connector.

The protocol for this connector is:

• 9600 baud • 8-bit • 1 stop bit • no parity • no ﬂow control

N For RS-232 connect transmit, receive, and ground connectors to the control system or PC.

Software control

Installation — Insert the supplied Extron DVD into DVD drive on a PC that is connected to

the MMX. The installation window opens automatically.

Select the Software tab, scroll to the Universal Switcher control program, and click on Install.

Follow the on-screen instructions to complete installation.

Startup and use — To start up the installed software, click on the desktop icon.

To use the software, refer to the MMX 32 VGA MTP Users’s Guide, available online at

www.extron.com, for details.

OUTPUT 1

2 1 3

OUTPUT 2

2 1 3

Press and hold Input 1

Button for Output 1.

Press and hold Input 3

Button for Output 2.

Setup Guide — MMX 32 VGA MTP cont’d

Extron USA - West

Headquarters

+800.633.9876

Inside USA / Canada Only

+1.714.491.1500

+1.714.491.1517 FAX

Extron USA - East

+800.633.9876

Inside USA / Canada Only

+1.919.863.1794

+1.919.863.1797 FAX

Extron Europe

+800.3987.6673

Inside Europe Only

+31.33.453.4040

+31.33.453.4050 FAX

Extron Asia

+800.7339.8766

Inside Asia Only

+65.6383.4400

+65.6383.4664 FA X

Extron Japan

+81.3.3511.7655

+81.3.3511.7656 FAX

Extron China

+400.883.1568

Inside China Only

+86.21.3760.1568

+86.21.3760.1566 FAX

Extron Middle East

+971.4.2991800

+971.4.2991880 FAX

68-789-50

Rev. A

03 10

Command ASCII

command

(host to

switcher)

Response

(switcher to

host)

Additional description

Create ties

Tie input X@ to

output X#, A and V

X@*X#! OutX# InX@ All]Tie input X@ audio and video to

output X#.

Tie input X@ RGB to

output X# X@*X#% OutX# InX@ RGB]Tie input X@ RGB to output X#.

Tie input X@ audio

to output X# X@*X#$ OutX# InX@ Aud]Tie input X@ audio to output X#.

RGB mute

RGB mute X#*1B VmtX#*1]Mute RGB output X#.

RGB unmute X#*0B VmtX#*0]Unmute RGB output X#.

Read RGB mute X#BX(]Show RGB mute status X(.

Global (where X# is not included, global RGB mute is activated.)

RGB mute all 1*B Vmt1]Mute all RGB.

RGB unmute all 0*B Vmt0]Unmute all RGB.

Audio mute

Audio mute X#*1Z AmtX#*1]Mute audio output X#.

Audio unmute X#*0Z AmtX#*0]Unmute audio output X#.

Read audio mute X#ZX(] Show audio mute status X(.

Global (where X# is not included, global audio mute is activated.)

Audio mute all 1*Z Amt1]Mute all audio.

Audio unmute all 0*Z Amt0]Unmute all audio.

View ties and output mute

View RGB output

tie

X#%X@]Output X# is tied to input X@

video.

View audio output

tie

X#$X@]Output X# is tied to input X@

audio.

Output mute X#VM X2)]Output X# mute status is X2)

X@ = Input number (for tie) 0 – 3, 0 = disconnected

X# = Output number 1 or 2

X( = 0 or 1 0 = off, 1 = on

X2) = Mute 0 = no mute, 1 = video mute, 2 = audio mute,

3 = video and audio mute

Control by SIS commands

The switcher can be controlled through the use of Extron SIS commands via the RS-232

connector. For full details on SIS commands refer to the MMX 32 VGA MTP Users’s Guide.

Tabla de contenidos

Otros manuales de Conmutador de matriz de Extron electronics

Extron electronics

Extron electronics XTP CrossPoint1600 Manual de usuario

Extron electronics

Extron electronics MMX 42 Series Manual de usuario

Extron electronics

Extron electronics DXP DVI Manual de usuario

Extron electronics

Extron electronics MVX Series Manual de usuario

Extron electronics

Extron electronics SMX System Manual de usuario

Extron electronics

Extron electronics MPX 423 A Manual de usuario

Extron electronics

Extron electronics CrossPoint 300 Series Manual de usuario

Extron electronics

Extron electronics MAV Plus Manual de usuario

Extron electronics

Extron electronics FOX 4G Matrix 14400 Manual de usuario

Extron electronics

Extron electronics CrossPoint 450 Plus 64 Series Manual de usuario

Extron electronics

Extron electronics CrossPoint 450 Plus 64 Series Manual de usuario

Extron electronics

Extron electronics MPX 423 A Manual de usuario

Extron electronics

Extron electronics MPX 423 A Manual de usuario

Extron electronics

Extron electronics DMP 64 Manual de usuario

Extron electronics

Extron electronics CrossPoint 450 Plus 64 Series Manual de usuario

Extron electronics

Extron electronics DMS 1600 Manual de usuario

Extron electronics

Extron electronics XTP II CrossPoint 1600 Manual de usuario

Extron electronics

Extron electronics CrossPoint 84 Manual de usuario

Extron electronics

Extron electronics TPX 88 Series Manual de usuario

Extron electronics

Extron electronics MPX 866 A Manual de usuario

Extron electronics

Extron electronics Matrix 3200 Series Manual de usuario

Extron electronics

Extron electronics MVX 128 Manual de usuario

Extron electronics

Extron electronics MPX Plus 866 A Manual de usuario

Extron electronics

Extron electronics Matrix 12800 wideband Manual de usuario

Manuales populares de Conmutador de matriz de otras marcas

Broadcast Tools

Broadcast Tools SS 8.2 Manual de usuario

Altimium

Altimium MATF32 Manual de usuario

ALFAtron

ALFAtron ALF-MUK44N Manual de usuario

Monoprice

Monoprice Blackbird 15377 Manual de usuario

Kramer

Kramer XL 3216VS Manual de usuario

PTN

PTN FMX12 Manual de usuario

CYP

CYP nT15GX01 Manual de usuario

Kramer

Kramer VP-2x2 Manual de usuario

Kramer

Kramer Sierra Video 6432V5xl Manual de usuario

TESmart

TESmart HMA0402A40 Manual de usuario

Octava

Octava HD4XSTPMX Manual de usuario

Intelix

Intelix FLX-88 Instrucciones de funcionamiento

Kramer

Kramer LASSEN XL 3232S Manual de usuario

Roland

Roland XS-1HD Manual de usuario

Kramer

Kramer VS-66HDCPxl Manual de usuario

Atlona

Atlona AT-HDMI-22M Manual de usuario

Link

Link HD8X8 Manual de usuario

AMX

AMX AVS-OP-2020-117 Instrucciones y recetas