Extron electronics DVI DA2 Manual de usuario

IMPORTANT:

Go to www.extron.com for the

complete user guide, installation

instructions, and specifications.

DVI DA2 and DVI DA4 • Setup Guide

These instructions provide a quick setup guide for the Extron DVI DA2 and DVI DA4. Installation

and service must be performed by authorized personnel only. To install, cable, and power on

the DVI DA2 and DVIDA4, do the following.

Step 1 — Mounting

Install the DVI DA2 or DVI DA4 on a desk, or mount it under a desk or in a rack.

Step 2 — DVI Input/Output Cable Connections

Connect these cables, but do not power on the equipment yet:

• Connect a DVI cable from the Input connector to the video source device.

• Connect a DVI cable from the Local Monitor connector to the desired local output device.

• Connect DVI cables from the output connectors to the desired display devices.

12V

0.4A MAX

POWER

DVI-D INPUT DVI-D OUTPUT

LOCAL MONITOR

1 2

DVI DA2

Ext

ron

I DA2

I Distribution

plier

Local Monitor

Flat Panel

Display

Step 3 — Power Cable Connections

Connect the 12 VDC power supply to the power receptacle of the unit.

DC Power

Input

POWER

12V

0.4A MA

Power Supply

Output Cord

SECTION A–

RidgesSmooth

DC Power Cord

Captive Screw Connector

Ground

+12 VDC input

External Power Supply

(12 VDC, 0.5 A max.)

Ground all

Devices

DVI DA2 and DVI DA4 • Setup Guide (Continued)

All trademarks mentioned are the property of their respective owners.

For information on safety guidelines, regulatory compliances, EMI/EMF compatibility,

accessibility, and related topics, see the Extron Safety and Regulatory Compliance Guide on

the Extron website.

68-1376-50 Rev. D

10 18

ATTENTION:

•If not provided with a power supply, this product is intended to be supplied by a UL Listed

power source marked “Class 2” or “LPS” and rated output 12VDC, 1.5 A minimum. Always

use a power supply provided by or specified by Extron. Use of an unauthorized power

supply voids all regulatory compliance certification and may cause damage to the supply

and the end product.

•Si le produit n’est pas fourni avec une source d’alimentation, il doit être alimenté par une

source d’alimentation certifiée UL de classe 2 ou LPS, avec une tension nominale 12 Vcc,

1,5 A minimum. Utilisez toujours une source d’alimentation fournie ou recommandée par

Extron. L’utilisation d’une source d’alimentation non autorisée annule toute certification de

conformité réglementaire, et peut endommager la source d’alimentation et l’unité.

•Unless otherwise stated, the AC/DC adapters are not suitable for use in air handling

spaces or in wall cavities. The power supply is to be located within the same vicinity as the

Extron AV processing equipment in an ordinary location, Pollution Degree 2, secured to the

equipment rack within the dedicated closet, podium, or desk.

•Sauf mention contraire, les adaptateurs CA/CC ne conviennent pas à une utilisation dans les

espaces d’aération ou dans les cavités murales. La source d’alimentation doit être placée

à proximité de l’équipement Extron dans un emplacement ordinaire soumis à un degré de

pollution de catégorie II, solidement xé au rack d’équipement d’une baie technique, d’un

pupitre, ou d’un bureau.

•The installation must always be in accordance with the applicable provisions of National

Electrical Code ANSI/NFPA 70, article 725 and the Canadian Electrical Code part 1, section

16. The power supply shall not be permanently xed to building structure or similar structure.

•Cette installation doit toujours être conforme aux dispositions applicables du Code américain

de l’électricité (National Electrical Code) ANSI/NFPA 70, article 725, et du Code canadien de

l’électricité, partie 1, section 16. La source d’alimentation ne devra pas être xée de façon

permanente à la structure de bâtiment ou à d’autres structures similaires.

NOTES: The length of the exposed wires in the stripping process is critical. The ideal length is

3/16inches (5 mm). If the exposed section is longer, the exposed wires may touch, causing

a short circuit between them. If it is shorter, the wires can be easily pulled out even if tightly

fastened by the captive screws.

Do not tin the wires. Tinned wire does not hold its shape and can become loose over time.

Step 4 — Applying Power

NOTE: Output 1 is used as DDC reference and Hotplug Detect and a local monitor must be

connected to it before the source device is powered on. Since Output 1 is used for reference,

all displays connected to the other outputs must be capable of handling resolutions greater

than or equal to that of Output 1.

•Power on the local monitor. •Power on the source input device.

•Power on the display devices.

Otros manuales para DVI DA2

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Amplificador de Extron electronics

Extron electronics

Extron electronics APP Manual de usuario

Extron electronics

Extron electronics NetPA U 2002 SB Manual de usuario

Extron electronics

Extron electronics IN3212 Manual de usuario

Extron electronics

Extron electronics XPA 2001-70V Manual de usuario

Extron electronics

Extron electronics XPA 1002 Manual de usuario

Extron electronics

Extron electronics SW2 VGA DA2 A Manual de usuario

Extron electronics

Extron electronics P/2 DA 2 WM/EC Manual de usuario

Extron electronics

Extron electronics ASA 204 Manual de usuario

Extron electronics

Extron electronics HDXP 1616 Manual de usuario

Extron electronics

Extron electronics Extron P/2 DA2xi Manual de usuario

Extron electronics

Extron electronics XPA U 1004 SB Manual de usuario

Extron electronics

Extron electronics VersaTools MDA 2V EQ Manual de usuario

Extron electronics

Extron electronics MPA 181T Manual de usuario

Extron electronics

Extron electronics Two Output 13W3 Sun and SGI Distribution Amplifier 13W3... Manual de usuario

Extron electronics

Extron electronics ADA 2/GLI 350 HV Manual de usuario

Extron electronics

Extron electronics NetPA 502 AT Manual de usuario

Extron electronics

Extron electronics DVI DA Plus Series Manual de usuario

Extron electronics

Extron electronics Fiber Optics Fox 4G DA8 Manual de usuario

Extron electronics

Extron electronics P/2 DA2 Plus Manual de usuario

Extron electronics

Extron electronics Video and Audio Line Drivers with Gain and EquaLization CVEQ 100... Manual de usuario

Extron electronics

Extron electronics XPA U 3502 Manual de usuario

Extron electronics

Extron electronics VersaTools MDA 3V Dual Manual de usuario

Extron electronics

Extron electronics VGA Distribution Amplifiers P/2 DA4xi s Manual de usuario

Extron electronics

Extron electronics VGA Distribution Amplifiers P/2 DA4xi s Manual de usuario

Manuales populares de Amplificador de otras marcas

ASTRO

ASTRO HVO V40 P Manual de usuario

Marantz

Marantz SUPERSCOPE BLA-545 Instrucciones de montaje

NAD

NAD CI980 Manual de usuario

Technics

Technics SE-CH770 Manual de usuario

Harman Kardon

Harman Kardon HK6300 Manual de usuario

NAD

NAD T975 Manual de usuario

McIntosh

McIntosh MA6850 Manual de usuario

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N Manual de usuario

Viatron

Viatron Autrix Manual de usuario

GME

GME GA9800 Manual de usuario

Atlas

Atlas CP700 Manual de usuario

Roland

Roland KC-1000 Manual de usuario

Pyle

Pyle PFMRA350BW Manual de usuario

Advantage

Advantage S-250 Manual de usuario

IRT Electronics

IRT Electronics DVA-3007 Manual de usuario

Dimavery

Dimavery BA-100 Series Manual de usuario

Sony

Sony XM-S400D Manual de usuario

Schertler

Schertler ROY X Manual de usuario