Extech Instruments 407119 Manual de usuario

User's Guide

Heavy Duty Hot Wire CFM Thermo-Anemometer

Model 407119

Model 407119Version 1.5 Oct 28, 2004

Warranty

EXTECH INSTRUMENTS CORPORATION warrants this instrument to be free of defects in parts and

workmanship for three years from date of shipment (a six month limited warranty applies on sensors and

cables). If it should become necessary to return the instrument for service during or beyond the warranty

period, contact the Customer Service Department at (781) 890-7440 ext. 210 for authorization or visit our

website at www.extech.com (click on ‘Contact Extech’ and go to ‘Service Department’ to request an RA

number). A Return Authorization (RA) number must be issued before any product is returned to Extech. The

sender is responsible for shipping charges, freight, insurance and proper packaging to prevent damage in

transit. This warranty does not apply to defects resulting from action of the user such as misuse, improper

wiring, operation outside of specification, improper maintenance or repair, or unauthorized modification.

Extech specifically disclaims any implied warranties or merchantability or fitness for a specific purpose and

will not be liable for any direct, indirect, incidental or consequential damages. Extech's total liability is limited

to repair or replacement of the product. The warranty set forth above is inclusive and no other warranty,

whether written or oral, is expressed or implied.

Introduction

Congratulations on your purchase of the Extech 407119 Thermo-Anemometer. The

407119 utilizes a telescoping antenna with built-in air velocity and temperature

measurement transducers. CFM (cubic feet per minute) measurements are displayed

after manually entering the area of the duct and then taking an air velocity measurement.

The 407119 includes a MIN/MAX display and a 20-point averaging feature. Careful use

of this meter will provide years of reliable service.

Specifications

General Specifications

Display Dual function 4-digit LCD

Measurement units Air Velocity: m/s, km/h, ft/min, knots, mph;

Air Flow: CMM (m3/min) and CFM (ft3/min);Temp: °C and °F

Data hold Freezes displayed reading

Sampling rate 1 second approx.

Sensors Air velocity sensor: Glass bead thermistor

Temperature sensor: Thermistor

MAX/MIN Memory Record and view Maximum and Minimum readings

Automatic Power off Auto shut off after 15 minutes

Data Output RS-232 PC serial interface with 16-bit data stream output

Operating

Temperature

Meter: 32 to 122°F (0 to 50°C)

Operating Humidity Max. 80% Relative Humidity

Power Supply Six (6) ‘AAA’ 1.5V batteries

Power Current Approx. DC 30mA

Weight (meter only) 0.78 lbs. (355g)

Dimensions Main instrument: 7.1 x 2.8 x1.3" (180 x 72 x 33mm)

Telescoping Sensor: 0.5" (12.7mm) diameter head;

37" (.94m) maximum antenna length with 78" (2m) cable

Model 407119Version 1.5 Oct 28, 2004

Range Specifications

Air Velocity Range Resolution Accuracy

0.20 – 9.99 m/s 0.01m/s (meters per second)

10.0 to 20.0 m/s 0.1

km/h (kilometers per

hour)

0.7 – 72.0 km/h 0.1

ft/min (feet per minute) 40 – 3940 ft/min 1

mph (miles per hour) 0.5 – 44.7 mph 0.1

knots (nautical miles per

hour)

0.4 to 38.8 knots 0.1

±5% full scale

Air Flow Measurements Range Resolution Area

CMM (cubic meters per

minute)

0 - 999,900 m3/min 0.001 to 100 0 to 9,999m2

CFM (cubic feet per

minute)

0 - 999,900 ft3/min 0.001 to 100 0 to 9,999ft2

Air Temperature Range Resolution Accuracy

32 to 122oF

(0 to 50oC) 0.1oF/C ±1.5oF (0.8oC)

Meter Description

1. Sensor input

2. RS-232 PC interface jack

3. LCD Display

4. Keypad

5. Rubber protective holster

6. Battery compartment (rear)

7. Air Velocity Sensor

8. Sliding sensor cover

9. Telescoping antenna

Note: To access the rear battery compartment

first remove the meter's rubber protective holster.

Model 407119Version 1.5 Oct 28, 2004

Operation

Initialization and Zero

The meter should always be zeroed at temperature before use. Do not rely on a zero display.

The meter does not display negative numbers.

1. Connect the sensor to the input jack on top of the meter.

2. Turn on the meter using the Power button. The meter will perform a self-test during

which the display will count down from 9999 to 0000.

3. Select the VELOCITY function using the FLOW/VELOCITY button. The LCD will

display VEL when the velocity mode is selected.

4. Select the desired temperature units using the C/F select button. The LCD will reflect

the selection.

5. Select the desired air velocity units using the UNIT button. The LCD will reflect the

selection.

6. Place the sensor cover in the UP (ZERO) position.

7. Place the sensor in the area to be measured and allow a short time for it to reach

temperature.

8. Press the ENTER/RESET button to zero the meter.

Air Velocity Measurements

1. Open the antenna to the desired length.

2. Slide the air velocity sensor cover down.

3. Place the sensor in the air current to be measured. Have the air flow meet the sensor

head in the direction of the white dot on the sensor head.

4. View the air velocity and temperature readings on the LCD Display. The large main

LCD display shows the Air Velocity reading. The lower LCD sub-display shows the

temperature reading.

Model 407119Version 1.5 Oct 28, 2004

Air Flow Measurements (CMM / CFM)

NOTE: Temperature is not displayed in the FLOW mode.

1. Perform the Initialization and Zero described earlier.

2. Select the FLOW mode using the FLOW/VELOCITY button. The LCD will display

FLOW when the flow function has been selected.

3. Select the desired air flow units: CMM (cubic meters per minute) or CFM (cubic feet

per minute) using the UNIT button. The LCD will reflect the selection.

4. Calculate the area of the duct or vent in square feet (not inches) or meters.

5. Press the AREA button to begin entering the area in m2or ft2. The left digit will begin

flashing.

Use the ►button to select the digit to set.

Use the ▲button increase the value of the flashing digit

Use the ▼button to decrease the value of the flashing digit

Use the ●RECORD/RECALL button to set the decimal point.

Press the ENTER/RESET button to save the area.

When the area has been entered, the bottom display will indicate the area entered in ft2

or m2.

6. Insert the probe into the area to be measured and the display will display the airflow.

The main LCD displays the air flow in CFM or CMM.

Flow Modes

For air flow measurements, three modes apply: Press the FLOW MODE button to select

one of the modes

NORMAL MODE, default mode, where the actual flow is indicated.

2/3V MAX MODE: LCD displays 2/3 the measured value.

AVG MODE: Up to 20 readings can be taken separately and averaged. Select the AVG

mode via the FLOW MODE button and then press the AVG START button to take a

reading. Up to 20 readings can be taken and averaged. The lower LCD display

provides a 1 to 20 counter that increments each time a reading is taken. The main LCD

displays the averaged air flow.

Data Hold Feature

1. While taking measurements, press the HOLD button to freeze a reading.

2. The HOLD indicator will appear on the LCD when the display is in Data Hold mode.

3. Press HOLD again to return to normal operation.

Maximum and Minimum Recording

The RECORD/RECALL feature allows the user to record and view the highest (MAX) and

lowest (MIN) readings.

1. Press the RECORD/RECALL button once. The REC indicator will appear on the

display and the meter will begin keeping track of the MAX and MIN values.

2. To view the MAX reading, press RECORD/RECALL again. The MAX indicator along

with the maximum reading will appear on the LCD display.

3. Press RECORD/RECALL again to view the minimum value, the MIN indicator along

with the minimum reading will appear on the LCD display.

4. To return to normal operation, press and hold the RECORD/RECALL button for

approx. 3 seconds. The display indicators REC, MAX, and MIN will disappear.

Note: Auto Power Off is disabled in the RECORD mode.

Model 407119Version 1.5 Oct 28, 2004



Support Hotline (781) 890-7440

Tech support: Ext. 200; Email: support@extech.com

Repair/Returns: Ext. 210; Email: [email protected]

Website: www.extech.com

Auto Power Off

To save battery life, the meter will automatically shut off after approximately 15 minutes of

operation. To disable this feature, press the RECORD/RECALL button and enter the

RECORD mode.

PC Interface

The 407119 is equipped with a 3.5mm jack (meter top) for connection to a PC for data

acquisition purposes. To obtain PC interface cabling and WindowsTM data acquisition

software, contact Extech Instruments. Instructions for use are provided with the optional

data acquisition kits.

Battery Replacement

When the LBT icon appears on the LCD, the 9V battery must be replaced.

1. Remove the rubber holster that surrounds the entire meter

2. Slide off the rear battery compartment

3. Replace the 9V battery

4. Affix the battery compartment cover and the meter holster

Calibration and Repair Services

Extech offers repair and calibration services for the products we sell. Extech also provides

NIST certification for most products. Call the Customer Service Department for information

on calibration services available for this product. Extech recommends that annual

calibrations be performed to verify meter performance and accuracy.

Model 407119Version 1.5 Oct 28, 2004

Useful Equations and Conversions

Area equation for rectangular or square ducts

Area equation for circular ducts

Cubic equations

NOTE: Measurements made in inches

must be converted to feet or meters before using the above formulae.

Unit of Measure Conversion Table

m/s ft/min knots km/h MPH

1 m/s 1196.87 1.944 3.6 2.24

1 ft/min 0.00508 10.00987 0.01829 0.01138

1 knot 0.5144 101.27 11.8519 1.1523

1 km/h 0.2778 54.69 0.54 10.6222

1 MPH 0.4464 87.89 0.8679 1.6071 1

Width (W)

Height (H)

Area (A) = Width (W) x Height (H)

CFM (ft3/min) = Air Velocity (ft/min) x Area (ft2)

CMM (m3/min) = Air Velocity (m/sec) x Area (m2) x 60

Radius Area (A) = 6x r2

Where 6 = 3.14 and r2= radius x

radius

Otros manuales para 407119

Tabla de contenidos

Otros manuales de Instrumento de medición de Extech Instruments

Extech Instruments

Extech Instruments 451112 Manual de usuario

Extech Instruments

Extech Instruments MO257 Manual de usuario

Extech Instruments

Extech Instruments 45160 Manual de usuario

Extech Instruments

Extech Instruments 407113 Manual de usuario

Extech Instruments

Extech Instruments ExStik EC500 Manual de usuario

Extech Instruments

Extech Instruments SL510 Manual de usuario

Extech Instruments

Extech Instruments HD750-NIST Manual de usuario

Extech Instruments

Extech Instruments ExStik EC510 Manual de usuario

Extech Instruments

Extech Instruments 433201A Manual de usuario

Extech Instruments

Extech Instruments SDL550 Manual de usuario

Extech Instruments

Extech Instruments EC210 Manual de usuario

Extech Instruments

Extech Instruments CO240 Manual de usuario

Extech Instruments

Extech Instruments HD750 Manual de usuario

Extech Instruments

Extech Instruments RH300 Manual de usuario

Extech Instruments

Extech Instruments CO100 Manual de usuario

Extech Instruments

Extech Instruments 461995 Manual de usuario

Extech Instruments

Extech Instruments RH390 Manual de usuario

Extech Instruments

Extech Instruments 45320 Manual de usuario

Extech Instruments

Extech Instruments HD750 Manual de usuario

Extech Instruments

Extech Instruments MO220 Manual de usuario

Extech Instruments

Extech Instruments MG310 Manual de usuario

Extech Instruments

Extech Instruments 380580 Manual de usuario

Extech Instruments

Extech Instruments SDL600 Manual de usuario

Extech Instruments

Extech Instruments 380973 Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario