EverFocus EZN Series Manual de usuario

Value IP Series Network Camera

2MP/5MP/8MP, H265, IR & WDR

Quick Installation Guide

EHN Series

EZN Series

This Quick Installation Guide can be applied to the following models:

Lens Type

2MP

5MP

8MP

Motorized

EHN1250

EZN1250

EHN2550

EZN2550

EHN2850 / EHN2850-15

EZN2850 / EZN2850-15

Fixed

EZN1240

EZN2540

EZN2840 / EZN2840-15

Release Date: May, 2019

All the images including product pictures or screen shots in this document are for example only.

The images may vary depending on the product and software version. Information contained in

this document is subject to change without notice.

EverFocus Taiwan:

2F., No.12, Ln. 270, Sec. 3, Beishen Rd., Shenkeng Dist., New Taipei City 222, Taiwan

TEL: +886 2 2662 2338 FAX: +886 2 2662 3632 www.everfocus.com.tw

1. Physical Description

EHN Series

EZN Series

SD Card Slot on

EHN 2MP/5MP Series

No.

Item Name

Descriptions

Light Sensor

Detects lights.

2IR LEDs

IR LEDs for infrared illumination in night vision

applications.

Lens

Camera lens.

Micro SD Card Slot

(for 8MP models) Insert a micro SD card.

Micro SD Card Slot

(for 2MP/5MP models)

Insert a micro SD card.

6 Micro SD Card Slot Insert a micro SD card.

7Sunshield Protect the camera from the direct fun rays.

8 Rotate Screw

Loosen the Rotate Screws (on both side) to adjust

the rotating angle.

9 Tilt Screw Loosen the Tilt Screw to adjust the tilting angle.

Pan Screw

Loosen the Pan Screw to adjust the angle.

Dimensions

EHN Series

117.3mm / 4.62"

Ø 147mm / 5.79"

EZN Series

Ø 83.58mm / 3.29"

82.18mm / 3.24"

241.18mm / 9.5"

Packing List

Please check that there is no missing items in the package before installing.

EHN Series

EZN Series

1. Camera x 1

2. MAC Address Sticker x 2

3. Cable Gland Kit x 1

4. Screw x 4

5. Screw Anchor x 4

6. Desiccant Bag x 1

7. Torx Wrench x 1

8. Mounting Sticker x 1

9. Quick Installation Guide x 1

10. Software CD x 1

1. Camera x 1

2. MAC Address Sticker x2

3. Cable Gland Kit x 1

4. Screw x 3

5. Screw Anchor x 3

6. Hexagon Wrench x 1

7. Quick Installation Guide x 1

8. Software CD x 1

Note:

1. Equipment configurations and supplied accessories vary by country. Please

consult your local EverFocus office or agents for more information. Please

also keep the shipping carton for possible future use.

2. Contact the shipper if any items appear to have been damaged in the

shipping process.

Optional Accessory

You can go to the product page on EverFocus’ website to check the related

optional accessories. www.everfocus.com.tw

2. Cables

The cables provide connections for network, BNC video output, power, audio

input / output and alarm input / output. A Reset Button Cable is also provided.

Please be noted that microphones / speakers with a (built-in) amplifier and

external power supply are required.

Note: To activate Audio function, the Audio function must be enabled. Please

refer to 5.5.2 Video Streaming in the User’s Manual.

EHN Series

Alarm Input / Output

LAN / PoE Cable

Video Output (BNC)

12VDC Power Input

Reset Button

Audio Output

Audio Input

Ground

EZN Series

Alarm Input / Output

LAN / PoE Cable

Video Output (BNC)

12VDC Power Input

Reset Button

Audio Output (White)

Audio Input (Red)

Ground

Alarm IO PIN Assignment

Alarm In

GND

COM

Alarm Out

Reset Button

The Reset Button can be used to restore the camera to factory default. When

the camera is powered up, press the Reset Button about 8 seconds to reboot the

camera.

3. Installation

3.1 EHN Series

1. Stick the supplied Mounting Sticker on the surface to mark the 4 screw

positions. Drill the 4 screw-depth holes on the surface and then push the

supplied 4 Screw Anchors into the screw holes. Optionally drill the bottom 2

Cable Holes if you want to run the cables through the surface.

+ +

Screw Position x 4

Optionally drill the 2 Cable Holes if

you want to run the cables through

the surface.

2. Remove the camera cover by unscrewing the 3 cover screws using the

supplied Torx Wrench (Left Image). Screw the camera base to the surface

using the supplied 4 Screws (Right Image).

3. Optionally insert a micro SD card into the card slot (please refer to 1. Physical

Description).

4. Adjust the pan / tilt / rotate angles of the camera.

5. Connect the camera to power. You can either connect the camera to a 12VDC

power source or to a PoE switch using the PoE cable.

6. Connect the camera to the network using the supplied Cable Gland Kit.

a. Insert a RJ-45 network cable (without the RJ-45 connector on the one end)

through the supplied Waterproof Ring, Cable Gland, Stopper and Screw

Cap accordingly.

Waterproof Ring Cable Gland Stopper Screw Cap

b. Connect the RJ-45 cable to the LAN/PoE Cable of the camera.

RJ-45 Cable

LAN/PoE Cable

c. Tightly screw the Cable Gland and Screw Cap to the Rugged RJ-45

Connector Cable.

Screw Cap

Cable Gland

d. Crimp the RJ-45 connector onto the RJ-45 network cable. Note that the

wires should be placed into the RJ-45 connector based on the following

order (from left to right).

Orange with white stripe

Orange

Green with white stripe

Blue

Blue with white stripe

Green

Brown with white stripe

Brown

7. Before screwing back the camera cover, remove the 3 old desiccant bags from

the inside of Camera Cover and replace them with the supplied Desiccant Bag.

Screw the camera cover back to the camera.

Stick the supplied desiccant bag

Remove the 3 desiccant bags

Note: Please screw back the

Camera Cover immediately

in case of reducing the

absorption capacity of the

desiccant bag inside the

camera body.

8. Now you can access the camera live view. See 4. Accessing the Camera.

3.2 EZN Series

1. Optionally insert a micro SD card into the card slot on the rear panel of the

camera. To do this, unscrew the 2 screw, remove the SD card slot cover and

then insert the micro SD card.

2. Drill three holes on the surface according to the screw positions on the

Camera Base. Push the supplied 3 Screw Anchors into the holes. Drill another

hole in the middle within the 3 screw holes if you wish to run the wires into

the surface. Screw the camera to surface using the supplied 3 Screws.

Screw Anchor

Screw

Surface

3. Adjust the pan/tilt/rotate angles of the camera by loosen the Pan/Tilt/Rotate

screws using the supplied Hexagon Wrench.

Tilt Screw

Pan Screw

Rotate Screws (both sides)

4. Connect the camera to power. You can either connect the camera to a 12VDC

power source or to a PoE switch using the PoE cable.

5. Connect the camera to the network using the supplied Cable Gland Kit. Please

refer to Step 6 in 3.1 EHN Series.

6. Now you can access the camera live view. See 4. Accessing the Camera.

4. Accessing the Camera

You can look up the IP address of the IP camera using the IP Utility (IPU)

program, which is included in the software CD.

The default network is DHCP. However, if there is no dynamic IP address

assigned to the device, its IP will switch to 192.168.0.10. By default, the ID is

admin and there is no password. Please input a password for the first-time login.

5. Important Note for Motorized Lens Models

For motorized lens models, if you find the live image out of

focus, please try the instructions below:

1. Go to the Live page and open the Lens Control panel

(see image on the right).

2. Click the Restore button for the lens to restore to the

default position, and then click the Auto Focus button.

3. If the image is still out of focus, adjust the focus by

clicking the Focus “+” or “-“ buttons.

* Motorized Lens Models: EHN1250/2550/2850/ 2850-15;

EZN1250/2550/2850/2850-15

Version: E1

Otros manuales para EZN Series

Este manual sirve para los siguientes modelos

Otros manuales de Cámara de seguridad de EverFocus

EverFocus

EverFocus ECD230/N3W Manual de usuario

EverFocus

EverFocus POLESTAR EHN7221 Manual de usuario

EverFocus

EverFocus EXZ330e Manual de usuario

EverFocus

EverFocus EI220 Manual de usuario

EverFocus

EverFocus EZN2550-SG Manual de usuario

EverFocus

EverFocus EPTZ9200 Series Manual de usuario

EverFocus

EverFocus EZ730 Manual de usuario

EverFocus

EverFocus EZ430 Manual técnico

EverFocus

EverFocus ECMD100i Manual técnico

EverFocus

EverFocus EM-500NHP1 Manual de usuario

EverFocus

EverFocus EQ200E Manual técnico

EverFocus

EverFocus EM700 Manual del propietario

EverFocus

EverFocus EZ180 Manual de usuario

EverFocus

EverFocus EPTZ3150 Manual de usuario

EverFocus

EverFocus M122-EJ230-002 Manual de usuario

EverFocus

EverFocus EHN3160 Plus Manual de usuario

EverFocus

EverFocus ED100 Series Manual de usuario

EverFocus

EverFocus EHH5101 Manual de usuario

EverFocus

EverFocus M099-VDE101-002 Manual de usuario

EverFocus

EverFocus EHD935 eZ.HD Series Manual de usuario

EverFocus

EverFocus EMN2560 Manual de usuario

EverFocus

EverFocus EHD300/N-2 Manual de usuario

EverFocus

EverFocus EQ700 Manual de usuario

EverFocus

EverFocus ED200 Series Manual de usuario

Manuales populares de Cámara de seguridad de otras marcas

Okina USA

Okina USA SIR36-870VF650LP Manual de usuario

Divio

Divio NDR155PA Manual de usuario

Canon

Canon VB-C500D Manual de usuario

Easy Access

Easy Access EasyGuard Manual de usuario

Vivotek

Vivotek FD9389-EHV-v2 Manual de usuario

TUYA

TUYA COSMO W2 Manual de usuario

Eusso

Eusso UNC7500-IR Guía de configuración

urmet domus

urmet domus 1096/204 Manual de usuario

VC VC20 series Manual de usuario

Axis

Axis Q1614 Manual de usuario

ieGeek

ieGeek DD201 Manual de usuario

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manual de usuario

Vicon

Vicon V662-D-1 Instrucciones de funcionamiento

Grundig

Grundig GCH-K0274P Manual de usuario

Lorex

Lorex VANTAGE LBC7032 Manual de usuario

4xem

4xem WPT Manual de usuario

Samsung

Samsung SCV-3082 Manual de usuario

Vitek

Vitek VTC-C544 Manual de usuario