EverFocus EHD150 Manual de usuario
1
1/
/3
3”
”
B
B/
/W
W
R
Ru
ug
gg
ge
ed
d
D
Do
om
me
e
C
Ca
am
me
er
ra
a
User’s Manual
and
Operation Instructions
E
HD
1
50
Notice
This manual is presented to the users of EHD150 by EverFocus Electronics
Corp. With years of engineering researches, EverFocus has spared no effort
to provide the high quality products to the worldwide users. For the policy
of continual product improvement, EverFocus reserves the right to make
changes to the product specifications and documentation without notice.
All the components of the products, including accessories, components, and
outlook, are based on the agreements of each deals to satisfy all kinds of
users. Meanwhile, please be advised that every step of operation must
follow the instruction of this manual to keep EHD150 working under the best
condition. Please notice that EverFocus will not be charged any claims or
renewing cases resulted from inappropriate operation.
Table of Contents
Safety Warning …………………………………………
1
Introduction
……………………………………………..2
Specification…………………………………………….3
Installation Instructions
………………………….….…4
Dip Switch Functions
…………………………….….…8
1. Do not install the camera near electric or magnetic fields.
Installed the camera away from TV, radio transmitter, magnet,
electric motor, transformer, audio speakers because the
magnetic fields generate from above devices will distort the
video image.
2. Do not install the camera in the high temperature environment.
Installed the camera away from stoves, or other heat
generating devices as the high temperature could cause
deformation, discoloration or other damages of the camera.
Install the camera at where the temperature range will stay
between -46℃to 50℃(-50℉to 122℉).
3.Never face the camera toward the sun.
Never aim the camera at the sun or other extremely bright objects
whether it is in use or not.
4. Cleaning
Do not touch the surface of CCD sensor by hand directly. Use
a soft cloth to remove the dirt from the camera body. Use lens
tissue or a cotton tipped applicator and ethanol to clean the
CCD sensor and the camera lens. When the camera is not in
use, put the cover cap on the lens mount.
5. Heater
Heater elements could be very hot!! Heaters are located inside
the camera housing and will active automatically while the
environment temperature is below 10℃. Do not touch the
heater element while it’s active.
Safety Warning
1
The most technically advanced EHD150 is the newest vandal-resistant B/W
Rugged Dome Camera from EverFocus Electronics. The B/W Rugged Dome
Camera can withstand a blow from a 10-pound sledgehammer and has a
built-in heater that allows for operation in low temperatures. It is perfect for all
high-profile crime-prone applications such as building entrances, retail stores,
and shopping malls. The extremely EHD150 is unquestionably one of the
world's toughest cameras and is your best choice for vandal resistance.
Main Features :
??Designed with advanced digital signal processing circuitry for high image
quality.
??The high sensitivity of 0.06 lux/F=1.6 is achieved by high –resolution
1/3” interline transfer CCD.
??DC12V or AC24V switches automatically power supply; Line Lock for
AC24V.
??S/N Ratio reaches 48 dB or more.
??Both board lens and vari-focal lens (3.5~8mm or 9~22mm) are available.
??Compact size: 130mm x 130 mm x 98.9mm
??Polycarbonate base withstand the impact of a 10 pounds sledgehammer,
smoke color or clear as option.
??Unique security screw locked
??Operating temperature –46 ~ +50 deg Celsius.
??Heater triggered when temperature less than 10 deg Celsius.
Introduc
tion
2
Specification
Pickup device: 1/3” interline transfer CCD
Picture element: NTSC :768(H) × 494(V)
PAL: 752(H)×582(V)
Horizontal resolution: 560 TV lines
Sensitivity: 0.06 lux /F=1.6
S/N ratio: >48dB(AGC off)
Weatherproof ratings: IP66
Electronic shutter: 1/60(1/50)~1/100,000(Board lens only)
IRIS Control: Auto (vari-focal lens only)
Auto gain control: on/off switch
Back light comp: on/off switch
Line Lock: on/off switch for 24VAC
Gamma correction: 0.45
Video output: 1.0Vp-p,75ohm
Power source: 12VDC+/-10%, 24VAC+/-10%
Power Consumption: 5W Max.
(15W when heater active; thermostatically controlled)
Sync.mode: Internal Sync. /Line lock (Only AC24V)
Dimension: 130mm x 130mm x 98.9mm
Lens: Board lens f=3.6,F=2.0
Vari-focal F=3.5~8mm, F=1.6
Heater auto activated temperature: 10℃, Heater optional
Operating temperature: -46℃to +50℃
Weight: 1.7kg
3
1. Loosen the 4 fix screws on the housing cover by using the attached wrench
(Figure 1). Carefully uncap the housing cover as the direction shown below
(Figure 2), please pay attention not to damage the lens. To remove the
housing cover, push the hinges to the bottom of the bracket, the hinges can
be easily removed from the bracket.
2. Remove the camera.
To remove the camera, first unplug the wire connection on the back of the
camera. Then loosen the 2 locking screws on the camera base, push the
camera base to the right (toward heater direction, as shown in Figure 3),
remove the camera from the mounting base. Reinstall the camera and the
cable while the base mounting is completed.
Installation Instructions
Locking Screws
Board Lens
Vari-FocalLens
Heater
4
Figure 1 Figure 2
Figure 3
3. Mounting the base.
Attach the base to the wall or ceiling, fix the base by the 4 setscrews
attached in the accessory pack. The dome is weighted 1.7kg, please make
sure if the mounting is strengthened enough to support it, if not,
please reinforce the mounting according to the environment.
Note: The diameter of the screw hole isψ4.7mm.
Caution: To prevent moisture leaking into the housing, apply an
appropriate gasket or sealant around the conduit connection.
Conduit plug setscrew
Side conduit entry
Back conduit entry
Mounting Setscrew
Mounting Setscrew
Mounting Setscrew
Mounting Setscrew
The camera comes with a conduit plug
pre-installed in the PF 1/2 conduit entry
on the side. The screw can be removed
and installed in the back conduit entry.
Loosen the conduit plug setscrew (as
shown in Figure 5) before removing the
conduit plug.
Side conduit entry (PF1/2)
Conduit plug
Back conduit entry (PF1/2)
5
Figure 4
Figure 5
4. Wire Connection
Connect the power supply cable (AC24V/DC12V), video output and alarm
output to the proper connectors shown as Figure 6.
The V. Phase adjustment screw is located on the termination board.
The vertical phase may require adjustment to synchronize the vertical
phase of the camera with other camera in the system when it is to be used
in the line-lock sync mode. Make the adjustment when the vertical phase
of the camera does not match with other cameras.
Termination Board
Video
Alarm COM
Micro Switch for Alarm trigger
GND
Alarm NO
Alarm NC
Power In
DC12V (+)or AC24V
V. Phase Adjustment VR
6
Figure 6
Power In
DC12V (-) or AC24V
5. View Angel Adjustment
The camera can be rotated 360°horizontally, and the vertical view angle
is 140°(as shown in Figure 7).Adjust the proper camera view angel as
needed. If a vari-focal lens is used, you may adjust the focus and zoom
of the lens to bring the object in focus. Be sure to loosen the locking
screws on the lens before you do the adjustments.
.
140°
360°
7
Figure 7
Lens fixing Screws
Otros manuales para EHD150
1
Tabla de contenidos
Otros manuales de Cámara de seguridad de EverFocus
EverFocus
EverFocus EHH5200 Manual de usuario
EverFocus
EverFocus M153-HDN552-001 Manual de usuario
EverFocus
EverFocus EZ350 Manual de usuario
EverFocus
EverFocus EBH5201 Manual técnico
EverFocus
EverFocus EZ760 Manual del propietario
EverFocus
EverFocus EQH5102 Manual de usuario
EverFocus
EverFocus WDII EQ600 Manual de usuario
EverFocus
EverFocus EZ-VF325NH Manual de usuario
EverFocus
EverFocus SG Series Manual de usuario
EverFocus
EverFocus EPN4230d Manual de usuario
EverFocus
EverFocus EZ-PLATECAM2-002 Manual de usuario
EverFocus
EverFocus EXZ330e Manual de usuario
EverFocus
EverFocus EQ900 eZ.HD Series Manual de usuario
EverFocus
EverFocus EBA2580 eZ.HD Series Manual de usuario
EverFocus
EverFocus EZ350 Manual de usuario
EverFocus
EverFocus Integrated Camera EI220 Manual de usuario
EverFocus
EverFocus EQ120 Manual de usuario
EverFocus
EverFocus ED350 Manual de usuario
EverFocus
EverFocus EHD360 Manual de usuario
EverFocus
EverFocus EMD990F Manual de usuario
